Isuzu KB P190. Service manual — part 1028
ON-VEHICLE SERVICE (AW30–40LE) 7A3-27
4. Install the spring plate.
a. Insert the detent pin into the base plate detent
groove until it touches the front wall (lever
assembly in N position).
RTW37ASH001001
b. Stack the short spring plate and tighten the
screws to the specified torque.
Screw torque
2 N
⋅m (0.2kgf⋅m/17 lb⋅in)
c. Check that the detent pin moves smoothly in the
detent groove (shift knob temporarily installed).
5. Temporarily install the sleeve.
6. Move the lever to the “P” position.
7. Adjust the clearance (2) between the detent plate
and the pin by moving the select lever knob sleeve
(1).
Detent plate and pin clearance
mm(in)
0.2 - 1.0 (0.01 - 0.04)
255R300002
8. Install the lamp assembly to the lamp socket.
a. Align the recessed portion of the lamp socket with
the protruding portion of the lamp assembly.
b. Insert the lamp assembly into the lamp socket
and rotate it 90 degrees clockwise.
9. Remove the sleeve and move the lever to the “N”
position.
10. Install the upper housing. Make sure that the 4
latched fasteners are securely closed.
11. Attach the harness connectors to the base plate.
12. Install the sleeve (rotate the sleeve clockwise the
same number of turns it was rotated
counterclockwise at disassembly).
13. Install the knob, the knob button, and the knob
spring.
14. Install the 2 screws securing the knob and tighten
them to the specified torque.
Screw torque: 2 N
⋅⋅⋅⋅m (0.2kgf⋅⋅⋅⋅m/17 lb⋅⋅⋅⋅in)
7A3-28 ON-VEHICLE SERVICE (AW30–40LE)
Shift Cable
RTW77ALF001101
Legend
(5) Bracket
(1) Select
lever
(6) Clip
(2) Shift cable retaining pawl
(7) Shift cable
(3) Manual shaft select lever
(8) Select lever base
(4) Adjuster
Remove or Disconnect
1. Block the wheels.
2. Disconnect the negative battery cable.
3. Move the select lever to the “N” position.
4. Remove the rear console and front console.
5. Disconnect the shift cable from the select lever.
6. Press on the shift cable retaining pawl to remove the
cable from the select lever base.
7. Disconnect the shift cable from the transmission
side.
8. Remove the shift cable from the bracket.
9. Pull the shift cable free from the bottom of the
vehicle.
ON-VEHICLE SERVICE (AW30–40LE) 7A3-29
Install or Connect
1. Install the shift cable toward the inside of the cabin
from the bottom of the vehicle.
2. Push the shift cable into the select lever base.
3. Connect the shift cable to the select lever.
4. Fix the shift cable to the bracket.
Install the clip on the marking of shift cable.
5. Check that the select lever is in the “N” position.
6. Check that the transmission is in the “N” position.
249R300002
7. Slide the cover in the direction shown by the arrow
(1).
8. Use an ordinary screwdriver to move the lock piece
from the position indicated by the arrow (2). Continue
to move the lock piece until the adjuster position
begins to change.
P1010012
9. Connect the shift cable to the manual shaft select
lever at the transmission side.
10. Insert the lock piece to the adjuster (cable length
adjustment).
11. Slide the cover on the adjuster and secure lock
piece.
P1010016-2
11. Press the select lever knob button 5 times.
Then check that the select lever moves smoothly to
each of its positions.
13. Check that the shift position indicated by the select
lever and the actual shift position are the same.
14. Install the front console and rear console.
15. Connect the negative battery cable.
16. Remove the wheel blocks.
7A3-30 ON-VEHICLE SERVICE (AW30–40LE)
Torque Specifications
RTW77ALF000501
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст