Isuzu KB P190. Service manual — part 2

0A-6 GENERAL INFORMATION

IDENTIFICATION

CHASSIS NUMBER

The chassis number is stamped on the right-hand side of the
chassis side member under the right door.

RTW50ASH000201

VEHICLE IDENTIFICATION PLATE

The vehicle identification plate is attached to the upper face of
the radiator sill in the engine compartment.

BODY AND OPTION IDENTIFICATION

PLATE

The body and option plate shows body style, body serial
number, paint and trim colour combination, paint number,
engine transmissions, axle ratio options and built date. The
built date is defined as 'the date of manufacture' by the
calendar month and year in which the body shell and power
train sub-assemblies are co-joined or moved from the
production line.

GENERAL INFORMATION 0A-7

LIFTING INSTRUCTIONS

If a lifting device other than the original jack is used, it is most important that the device be applied only to the
correct lifting points. (See the illustration.) Raising the vehicle from any other point may result in serious damage.

Lifting Points and Supportable Point-Locations

RTW50AXF000201

0A-8 GENERAL INFORMATION

RUW50ASH000101

LIFTING POINT; FRONT
4

××××2 model

• When using floor jack, lift the center of 1st cross member.

RTW60ASH000101

4

××××4 model

• When using floor jack, lift the center of front axle case.

RTW60ASH000201

SUPPORTABLE POINT; FRONT

• Position the chassis stands at the bottom of the frame side

member, backward of front wheel.

RTW30ASH000101

LIFTING POINT; REAR

• When using floor jack, lift the center of rear axle case.

RTW30ASH000201

SUPPORTABLE POINT; REAR

• Position the chassis stands at the bottom of the frame side

member, forward of the rear wheel.

GENERAL INFORMATION 0A-9

CONVERSION TABLE

TABLE OF CONTENTS

PAGE

Length . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 0A-10

Area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 0A-11

Volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0A-12

Mass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0A-13

Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ... 0A-14

Torque . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 0A-15

Temperature. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0A-16

LENGTH

MILLIMETERS TO INCHES

mm in. mm in. mm in. mm

in.

1 0.0394 26 1.0236 51 2.0079 76

2.9921

2 0.0787 27 1.0630 52 2.0472 77

3.0315

3 0.1181 28 1.1024 53 2.0866 78

3.0709

4 0.1575 29 1.1417 54 2.1260 79

3.1102

5 0.1969 30 1.1811 55 2.1654 80

3.1496

6 0.2362 31 1.2205 56 2.2047 81

3.1890

7 0.2756 32 1.2598 57 2.2441 82

3.2283

8 0.3150 33 1.2992 58 2.2835 83

3.2677

9 0.3543 34 1.3386 59 2.3228 84

3.3071

10 0.3937 35 1.3780 60 2.3622 85

3.3465

11 0.4331 36 1.4173 61 2.4016 86

3.3858

12 0.4724 37 1.4567 62 2.4409 87

3.4252

13 0.5118 38 1.4961 63 2.4803 88

3.4646

14 0.5512 39 1.5354 64 2.5197 89

3.5039

15 0.5906 40 1.5748 65 2.5591 90

3.5433

16 0.6299 41 1.6142 66 2.5984 91

3.5827

17 0.6693 42 1.6535 67 2.6378 92

3.6220

18 0.7087 43 1.6929 68 2.6772 93

3.6614

19 0.7480 44 1.7323 69 2.7165 94

3.7008

20 0.7874 45 1.7717 70 2.7559 95

3.7402

21 0.8268 46 1.8110 71 2.7953 96

3.7795

22 0.8661 47 1.8504 72 2.8346 97

3.8189

23 0.9055 48 1.8898 73 2.8740 98

3.8583

24 0.9449 49 1.9291 74 2.9134 99

3.8976

25 0.9843 50 1.9685 75 2.9528 100

3.9370

101 3.9764 111 4.3701 121 4.7638 131

5.1575

102 4.0157 112 4.4094 122 4.8031 132

5.1968

103 4.0551 113 4.4488 123 4.8425 133

5.2362

104 4.0945 114 4.4882 124 4.8819 134

5.2756

105 4.1339 115 4.5276 125 4.9213 135

5.3150

106 4.1732 116 4.5669 126 4.9606 136

5.3543

107 4.2126 117 4.6063 127 5.0000 137

5.3937

108 4.2520 118 4.6457 128 5.0394 138

5.4331

109 4.2913 119 4.6850 129 5.0787 139

5.4724

INCHES TO MILLIMETERS

in. mm in. mm

1/64

0.3969

33/64

13.0969

1/32

0.7938

17/32

13.4938

3/64

1.1906

35/64

13.8906

1/16

1.5875 9/16

14.2875

5/64

1.9844

37/64

14.6844

3/32

2.3813

19/32

15.0813

7/64

2.7781

39/64

15.4781

1/8

3.1750 5/8

15.8750

9/64

3.5719

41/64

16.2719

5/32

3.9688

21/32

16.6688

11/64

4.3656

43/64

17.0656

3/16

4.7625 11/16

17.4625

13/64

5.1594

45/64

17.8594

7/32

5.5563

23/32

18.2563

15/64

5.9531

47/64

18.6531

1/4

6.3500 3/4

19.0500

17/64

6.7469

49/64

19.4469

9/32

7.1438

25/32

19.8438

19/64

7.5406

51/64

20.2406

5/16

7.9375 13/16

20.6375

21/64

8.3344

53/64

21.0344

11/32

8.7313

27/32

21.4313

23/64

9.1281

55/64

21.8281

3/8

9.5250 7/8

22.2250

25/64

9.9219

57/64

22.6219

13/32

10.3188

29/32

23.0188

27/64

10.7156

59/64

23.4156

7/16

11.1125 15/16

23.8125

29/64

11.5094

61/64

24.2094

15/32

11.9063

31/32

24.6063

31/64

12.3031

63/64

25.0031

1/2

12.7000 1

25.4000