Isuzu Trooper (1998-2002 year). Service manual — part 569
6A – 84 ENGINE MECHANICAL
PISTON AND CONNECTING ROD
5
8
7
3
1
2
6
4
012RW061
Legend
(1)
Cylinder Head Assembly
(2)
Crank Case
(3)
Connecting Rod Bearing Cap
(4)
Connecting Rod
(5)
Piston Ring
(6)
Piston Pin
(7)
Piston Pin Snap Ring
(8)
Piston
ENGINE MECHANICAL 6A – 85
DISASSEMBLY
1. Cylinder Head Assembly
1) Refer to “Cylinder head” in this manual.
2. Crank Case Assembly
1) Refer to “Crank Case” in this manual.
3. Connecting Rod Bearing Cap
4. Piston and Connecting Rod
1) Remove carbon deposits from the upper portion
of the cylinder wall with a scraper before
removing the piston and connecting rod.
5. Piston Ring
Remove the piston rings with a piston ring
expander.
Arrange the removed piston rings in the cylinder
number order.
6. Piston Pin Snap Ring
1) Use a pair of pliers to remove the piston pin
snap rings.
7. Piston Pin
1) Remove piston pin from piston assembly.
NOTE: Keep the parts removed from each cylinder
separate. All parts must be reinstalled in their original
positions.
8. Piston
9. Connecting Rod
INSPECTION AND REPAIR
PISTON AND PISTON RING
Pistons
Carefully clean away all the carbon adhering to the
piston head and the piston ring grooves.
NOTE: Never use a wire brush to clean the pistons.
Damage will result. Visually check each piston for
cracking, scoring, and other signs of excessive wear. If
any of the above conditions are present, the piston
must be replaced.
Piston Diameter
1. Measure the piston outside diameter with
micrometer at the piston grading position.
Piston Grading Position: 69.75 mm (2.7461 in)
from piston head
Piston Outside Diameter
mm(in)
Grade Mark
Outside Diameter
A
95.320 – 95.329 (3.7527 – 3.7531)
B
95.330 – 95.339 (3.7531 – 3.7535)
C
95.340 – 95.349 (3.7535 – 3.7539)
015RW082
015RW077
015LV014
6A – 86 ENGINE MECHANICAL
Legend
(1) Piston Grade
(2) Piston Front Mark
(3) Part Number
The grade for piston outside diameter is stamped
on the piston head.
Measure the cylinder bore diameter at measuring
points.
If the piston clearance does not conform to the
specified value, the pistons most be replaced.
Piston Clearance:
0.092 – 0.110 mm (0.0036 – 0.0043 in)
Cylinder Bore Diameter
mm(in)
Grade Mark
Cylinder Bore Diameter
A
95.421 – 95.430 (3.7567 – 3.7571)
B
95.431 – 95.440 (3.7571 – 3.7575)
C
95.441 – 95.450 (3.7575 – 3.7579)
Legend
Measuring point 1 = 20 mm
2 = 90 mm
3 = 160 mm
Piston rings
Any worn or damaged part discovered during engine
overhaul must be replaced with a new one.
1. Ring end gap measurement
1) Insert the piston ring into the cylinder bore.
2) Push the ring by the piston, at the right angle to
the wall, into the point at which the cylinder bore
diameter is the smallest.
3) Measure the ring end gap.
NOTE: The piston ring is stamped with a discerning
mark on the upper face of piston ring.
1
3
2
015RW080
012RW071
3
2
1
012RW117
012RW051
ENGINE MECHANICAL 6A – 87
Discerning Mark
Piston Ring
Discerning Mark
1st compression ring
1N
2nd compression ring
2N
Ring End Gap
mm(in)
Piston Ring
Standard Gap
Limit
1st
0.25 – 0.40
compression ring
(0.0098 – 0.0157)
2nd
0.20 – 0.35
1.5
compression ring
(0.0079 – 0.0138)
(0.0590)
Oil ring
0.10 – 0.30
(0.0039 – 0.0118)
2. Measure the clearance between the piston ring
groove and the piston ring with a feeler gauge. If the
piston ring groove/piston ring clearance exceeds
the specified limit, the piston and/or piston rings
must be replaced.
mm(in)
Standard
Limit
1st
0.05 – 0.09
Compression
(0.0020 – 0.0035)
ring
2nd
0.05 – 0.09
0.15
(0.0020 – 0.0035)
(0.0059)
Oil ring
0.03 – 0.07
(0.0012 – 0.0028)
Piston pin
Visually inspect the piston pin for cracks, flaws, and
other damage and replace if necessary.
1. Use a micrometer to measure the piston pin outside
diameter in both directions at three different
positions. If the measurement exceeds the
specified limit, the piston pin must be replaced.
Standard: 30.995 – 31.000 mm (1.2212 – 1.2214 in)
Limit: 30.97 mm (1.2202 in)
N
012RW037
015RW076
012RW082
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст