Isuzu Trooper (1998-2002 year). Service manual — part 1048
SEATS
8G–5
11. Remove the seat back assembly.
D
Remove the clips (2) from the seat heater harness
(1), and separate the seat heater connector (3)
(models with the seat heater).
750RW029
D
Remove the seat back assembly fixing nut on the
opposite side of the reclining device.
750RS007
12. Remove the guide holder.
D
Pull the guide holder out by holding the bottom end
of it from the seat back assembly.
13. Remove the trim cover.
D
Remove the trim cover hog rings from the back side
of the seat back.
D
With close attention paid to the hog rings and the
wire which connect the trim cover and the pad and
frame assembly, remove the trim cover while
turning it up.
14. Remove the pad and frame assembly.
15. Remove the seat heater assembly.
16. Remove the seat adjuster.
D
Disconnect the release wire(4) and remove the
fixing bolts.
750RW006
D
Remove the seat belt buckle assembly.
17. Remove the height adjuster.
18. Remove the spacer (W/O height adjuster).
19. Remove the seat cushion assembly.
20. Remove the trim cover.
D
Remove the trim cover hog rings from the back side
of the seat cushion assembly.
D
With close attention paid to the hog rings and the
wire which connect the trim cover and the pad and
frame assembly, remove the trim cover while
turning it up.
21. Remove the frame assembly.
22. Remove the pad assembly.
23. Remove the seat heater assembly.
Reassembly
To reassembly, follow the disassembly steps in the
reverse order, noting the following point.
1. Tighten the armrest assembly fixing bolts to the
specified torque.
Torque: 18 N·m (1.8 kg·m/13 lb ft)
2. Tighten the reclining device fixing bolts to the
specified torque.
Torque: 47 N·m (4.8kg·m/35 lb ft)
8G–6
SEATS
Disassembled View (SWB)
750RX018
Legend
(1) Head Rest
(2) Seat Back Assembly
(3) Back Board Assembly
(4) Pad & Frame Assembly
(5) Trim Cover
(6) Guide Holder
(7) Reclining Device
(8) Slide Cover
(9) Reclining Knob
(10) Frame Assembly
(11) Pad Assembly
(12) Trim Cover
(13) Walk–in Cover
(14) Walk–in Assembly
(15) Seat Adjuster/Seat Adjuster (W/Pretensioner)
(16) Release Wire
(17) Seat Belt Buckle Assembly
(18) Spacer
(19) Seat Cushion Assembly
(20) Hinge Cover
Disassembly
1. Remove the head rest.
2. Remove the reclining knob.
3. Remove the side cover.
4. Remove the hinge cover.
5. Remove the back board assembly.
D
Pull out the back board while prying the clip of the
back board free from the seat back assembly.
SEATS
8G–7
6. Remove the reclining device.
D
Turn up the seat back trim cover in order to remove
the reclining device fixing bolts.
750RS006
D
Remove the push nut (2) and disconnect walk-in
cable (3) from reclining device (1).
750RW034
7. Remove the seat back assembly.
D
Remove the seat back assembly fixing nut on the
opposite side of the reclining device.
750RS007
8. Remove the guide holder.
D
Pull the guide holder out by holding the bottom end
of it from the seat back assembly.
9. Remove the trim cover.
D
Remove the trim cover hog rings from the back side
of the seat back.
D
With close attention paid to the hog rings and the
wire which connect the trim cover and the pad and
frame assembly, remove the trim cover while
turning it up.
10. Remove the pad and frame assembly.
11. Remove the walk-in cover.
12. Remove the seat adjuster.
D
Disconnect the release wire (4) and remove the
fixing bolts.
750RW006
D
Remove the seat belt buckle assembly.
8G–8
SEATS
13. Remove the walk-in assembly (passenger side).
14. Remove the spacer (driver side).
15. Remove the seat cushion assembly.
16. Remove the trim cover.
D
Remove the trim cover hog rings from the back side
of the seat cushion assembly.
D
With close attention paid to the hog rings and the
wire which connect the trim cover and the pad and
frame assembly, remove the trim cover while
turning it up.
17. Remove the frame assembly.
18. Remove the pad assembly.
Reassembly
To reassembly, follow the disassembly steps in the
reverse order, noting the following point.
1. Tighten the armrest assembly fixing bolts to the
specified torque.
Torque: 18 N·m (1.8 kg·m/13 lb ft)
2. Tighten the reclining device fixing bolts to the
specified torque.
Torque: 47 N·m (4.8kg·m/35 lb ft)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст