Mercedes-Benz ML320. Service manual — part 284
CHANGE REAR DOME LAMP - AR82.20-P-0113-01GH
1. Put dome lamp on workbench.
2. Remove all stiffening ribs (1) on edge.
Only for vehicles with lamella roof, code 417a.
3.1 Measure 13 mm (a) from the front edge and mark.
Only for vehicles with lamella roof, code 417a.
4.1 Cut dome lamp at the mark.
5 Deburr all cutting edges.
Fig. 173: Identifying Rear Dome Lamp Stiffening Ribs On Edge
REMOVE/INSTALL REAR DOME LAMP - AR82.20-P-0113GH
MODEL 163.113 /128 /136 /154 /157 /172 /174 /175
3
Release socket (3) for
bulb (2) by pressing in
The bulb socket is
clipped to the overhead
control panel.
4
Pull dome lamp switch
(4) off of reflector
housing (6)
5
Unscrew screws (5) from
reflector housing (6) on
left and right on overhead
control panel (1)
6
Pry reflector housing (6)
out of overhead control
panel (1)
Avoid damaging
reflector housing
7
Reinstall in opposite
order
2001 Mercedes-Benz ML320
1998-2005 ACCESSORIES & BODY, CAB Electrical System - Body - 163 Chassis
me
Shown on model 163 without Parktronic system (PTS), code 220a
Fig. 174: Identifying Rear Dome Lamp Components
Remove/Install
1
Prize off glass
cover (1) of the
rear interior lamp
(E15/3) and fold up
until it reaches the
limit stop
2.1
Disconnect
connector from
Parktronic system
warning display
Only with Parktronic system (PTS), code
220a.
3
Remove rear
interior lamp
(E15/3) from
inside roof lining
For removal pull dome lamp on rear
housing edge downward and simultaneously
forward.
4
Remove connector
(2) from rear
interior lamp
(E15/3)
5
Install in the
reverse order
Installation: If dome lamp is replaced in
models 163.113 /128 /136 /154 /172 /174 /175
2001 Mercedes-Benz ML320
1998-2005 ACCESSORIES & BODY, CAB Electrical System - Body - 163 Chassis
me
REMOVE/INSTALL FRONT OVERHEAD CONTROL PANEL - AR82.20-P-1100GH
MODEL 163.113 /128 /136 /154 /157 /172 /174 /175
Fig. 175: Identifying Front Overhead Control Panel Components
without Parktronic system (PTS), code 220a
up to vehicle identification number
A346574: ?
Changing dome lamp in the rear
AR82.20-P-0113-
01GH
Changing dome
lamp in the rear
BT82.20-P-0001-
03GH
Remove/install
1
Remove garage door
opener flap (1) from
overhead control panel (2)
2
Unclip cover (3) on the
sliding/tilting roof switch
(S13/2)
4 clips.
3
Unclip glass covers (4)
from interior lights
4
Unscrew screws (5)
2001 Mercedes-Benz ML320
1998-2005 ACCESSORIES & BODY, CAB Electrical System - Body - 163 Chassis
me
Fig. 176: Identifying Hooked Extraction Tool (140 589 02 33 00)
REMOVING AND INSTALLING WIPER ARM - AR82.30-P-6100GH
MODEL 163.113 /128 /136 /154 /157 /172 /174 /175
below garage door opener
flap (1) and glass covers
(4)
5
Unclip clips (black) (7)
next to the light switches
Installation:
Counterhold mounting
plate with puller hooks
inside of headliner.
Hooked extraction
tool
Fig. 168
6
Press both retaining clips
(6) to rear and
simultaneously press
overhead control panel (2)
to front
Position narrow
plastic wedge or
screwdriver in front of
retaining lugs.
7
Remove overhead control
panel (2) downward
8
Remove sliding/tilting
roof switch (S13/2)
AR77.20-P-0001GH
9.1
Remove trip computer
control module (TRIP)
(N41)
With code 245, trip
computer, only.
AR54.50-P-0001GH
10
Detach interior/roof
connector (X18/2) from
overhead control panel (2)
11
Remove overhead control
panel (2)
12
Install in the reverse order
2001 Mercedes-Benz ML320
1998-2005 ACCESSORIES & BODY, CAB Electrical System - Body - 163 Chassis
me
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст