Mercedes-Benz ML320. Service manual — part 89
183
Controls in detail
Useful features
Step 5:
왘
When the indicator lamp 6 flashes
rapidly, release both buttons.
Step 6:
왘
Press and hold the just-trained inte-
grated signal transmitter button and
observe the indicator lamp 6.
If the indicator lamp 6 stays on con-
stantly, programming is complete and
your device should activate when the
integrated signal transmitter button is
pressed and released.
Step 7:
왘
To program the remaining two buttons,
repeat the steps above starting with
step 3.
Rolling code programming
To train a garage door opener (or other roll-
ing code devices) with the rolling code fea-
ture, follow these instructions after
completing the “Programming” portion
(steps 1 through 6) of this text. (A second
person may make the following training
procedures quicker and easier.)
Step 8:
왘
Locate “training” button on the garage
door opener motor head unit.
Exact location and color of the button
may vary by garage door opener brand.
Depending on manufacturer, the “train-
ing” button may also be referred to as
“learn”or “smart” button. If there is dif-
ficulty locating the transmitting button,
refer to the garage door opener opera-
tor’s manual.
i
The indicator lamp 6 flashes the first
time the signal transmitter button is
programmed. If this button has already
been programmed, the indicator lamp
will only start flashing after 20 sec-
onds.
i
If the indicator lamp 6 flashes rapidly
for about two seconds and then turns
to a constant light, continue with pro-
gramming steps 8 through 12 as your
garage door opener may be equipped
with the “rolling code” feature.
컄컄
184
Controls in detail
Useful features
Step 9:
왘
Press “training” button on the garage
door opener motor head unit.
The “training light” is activated.
You have 30 seconds to initiate the follow-
ing step.
Step 10:
왘
Firmly press, hold for two seconds and
release the programmed integrated
signal transmitter button (3, 4
or 5).
Step 11:
왘
Press, hold for two seconds and re-
lease same button a second time to
complete the training process.
Some garage door openers (or other rolling
code equipped devices) may require you to
perform this procedure a third time to
complete the training.
Step 12:
왘
Confirm the garage door operation by
pressing the programmed integrated
signal transmitter button (3, 4
or 5).
Step 13:
왘
To program the remaining two buttons,
repeat the steps above starting with
step 3.
Gate operator/Canadian programming
Canadian radio-frequency laws require
transmitter signals to “time-out” (or quit)
after several seconds of transmission
which may not be long enough for the inte-
grated signal transmitter to pick up the sig-
nal during programming. Similar to this
Canadian law, some U.S. gate operators
are designed to “time-out” in the same
manner.
If you live in Canada or if you are having dif-
ficulties programming a gate operator (re-
gardless of where you live) by using the
programming procedures, replace step 4
with the following:
컄컄
185
Controls in detail
Useful features
Step 4:
왘
Continue to press and hold the inte-
grated signal transmitter button (3,
4 or 5) while you press and re-press
(“cycle”) your hand-held remote con-
trol transmitter 1 every two seconds
until the frequency signal has been
learned. Upon successful training, the
indicator lamp 6 will flash slowly and
then rapidly after several seconds.
왘
Proceed with programming step 5 and
step 6 to complete.
Operation of remote control
왘
Switch on ignition.
왘
Select and press the appropriate inte-
grated signal transmitter button (3,
4 or 5 to activate the remote con-
trolled device.
The integrated remote control trans-
mitter continues to send the signal as
long as the button is pressed – up to
20 seconds.
Erasing the remote control memory
왘
Switch on ignition.
왘
Simultaneously hold down the signal
transmitter buttons 3 and 5, for ap-
proximately 20 seconds, or until the in-
dicator lamp 6 flashes rapidly. Do not
hold for longer than 30 seconds.
The codes of all three channels are
erased.
Reprogramming a single integrated
signal transmitter button
To program a device using a signal trans-
mitter button previously trained, follow
these steps:
왘
Press and hold the desired signal trans-
mitter button (3, 4 or 5). Do not re-
lease the button.
왘
The indicator lamp will begin to flash af-
ter 20 seconds. Without releasing the
integrated signal transmitter button,
proceed with programming starting
with step 3.
i
If you sell your vehicle, erase the codes
of all three channels.
186
Controls in detail
Useful features
Trip computer*
The trip computer is located in the
overhead console.
1 RESET
2 MODE
3 Display
Switching on the trip computer
왘
Switch on ignition.
Display 3 shows one of the available
functions.
왘
If a function display does not appear,
press MODE 2.
Selecting functions
왘
Press MODE 2 repeatedly until the
desired display appears.
The functions are displayed in the follow-
ing order:
앫
Date
앫
Compass
앫
Stop watch
앫
Present fuel consumption
앫
Average fuel consumption
앫
Distance remaining
앫
Country
앫
Switching off trip computer
Setting the date
왘
Press MODE 2 repeatedly until the
date appears.
왘
Press RESET 1.
The month shown flashes.
왘
Press MODE 2 to advance to selected
month.
왘
Press RESET 1.
The day shown flashes.
왘
Press MODE 2 to advance to selected
day.
왘
Press RESET 1.
The year shown flashes.
왘
Press MODE 2 to advance to selected
year.
왘
Press RESET 1.
The display stops flashing and the date
is set.
i
With engine not running, the display
switches off automatically 30 seconds
after the last entry.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст