Mercedes-Benz: engine M272, M273. Service manual — part 5
AR05.20-P-6010-01VB
Inspect basic position of camshaft
Shown without pulse wheels on the
camshaft adjusters
1
Crank the engine at the crankshaft in
Turn the direction of engine rotation
(arrow) to 40° crank angle after ignition
TDC.
The 40° marking (1) on the belt
pulley must be aligned with the
positioning edge (2) on the timing case
cover.
The markings (3) on the camshaft
adjusters face upward, and the
markings (4) align with the contact
surfaces on the cylinder head covers.
P05.20-2164-06
Страница 1 из 1
© Daimler AG, 07.04.13, G/07/14, ar05.20-p-6010-01vb, Inspect basic position of camshaft
ENGINE 272, 273 Grundstellung der Nockenwellen bei ausgebauten vorderen Deckeln am Zylinderkopf bei 40° Kurbelwinkel nach OT'
AR05.20-P-7201-05VA
Lock the gear backlash compensation
The tooth flanks (1, 2) are held against each other by spring pressure and should not be
skewed, otherwise the camshaft adjuster will be irreparably damaged
1
Insert the drift (3, diameter 3mm) into the bore (4) of the cover plate and lock the tooth
flanks (1, 2) with each other.
Push the drift (3) through to the end of tooth flank (2).
To allow the drift (3) to be inserted more easily, align the tooth flanks with each other
(in the direction of the arrows).
Shown on camshaft adjuster, engine 273.965
P05.20-2160-03
Shown on camshaft adjuster, engine 272.968
P05.20-2322-01
Страница 1 из 1
© Daimler AG, 07.04.13, G/07/14, ar05.20-p-7201-05va, Lock the gear backlash compensation
ENGINE 272, 273
AR05.20-P-7201-06VA
Loosen/tighten the center valves
Camshaft, camshaft adjustment
Number
Designation
Engine
Engine
272
273
BA05.20-P-1009-02A
Center valve for pulse wheel/
Nm
145
145
camshaft adjuster to camshaft
Counterhold camshafts at the rear with a Torx screwdriver bit using a suitable tool to
unfasten and fasten the center valves. Before installing, the center valves must be lubricated
with oil on the contact surfaces with the pulse wheels.
Center valves of right cylinder head
1
Loosen the center valves in the direction of the arrow.
2
Tighten the center valves against the direction of the arrow.
P05.20-2161-01
Center valves of left cylinder head
3
Loosen the center valves in the direction of the arrow.
4
Tighten the center valves against the direction of the arrow.
P05.20-2162-01
Страница 1 из 1
© Daimler AG, 07.04.13, G/07/14, ar05.20-p-7201-06va, Loosen/tighten the center valves
ENGINE 272, 273
AR05.20-P-6010-01VB
Inspect basic position of camshaft
Shown without pulse wheels on the
camshaft adjusters
1
Crank the engine at the crankshaft in
Turn the direction of engine rotation
(arrow) to 40° crank angle after ignition
TDC.
The 40° marking (1) on the belt
pulley must be aligned with the
positioning edge (2) on the timing case
cover.
The markings (3) on the camshaft
adjusters face upward, and the
markings (4) align with the contact
surfaces on the cylinder head covers.
P05.20-2164-06
Страница 1 из 1
© Daimler AG, 07.04.13, G/07/14, ar05.20-p-6010-01vb, Inspect basic position of camshaft
ENGINE 272, 273 Grundstellung der Nockenwellen bei ausgebauten vorderen Deckeln am Zylinderkopf bei 40° Kurbelwinkel nach OT'
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст