Mercedes-Benz Sprinter / Dodge Sprinter. Service manual — part 182
PLATE 9277
INSTALLER 9278
WRENCH 9279
WRENCH 9290
INSTALLER 9291
SPREADER ADAPTERS 9317
INSTALLER 9523
VA
REAR AXLE
3 - 21
DIAL INDICATOR 9524
INSTALLER 9548
ARBOR DISC 9571
PINION BLOCK 9572
DUMMY BEARING 9573
3 - 22
REAR AXLE
VA
SHAFT - AXLE SINGLE REAR WHEEL
REMOVAL-SINGLE REAR WHEEL
(1) Remove wheels.
(2) Detach front brake cable.
(3) Pull ABS sensor (18) together with clamp bush-
ing (19) out of bearing cap (Fig. 6).
(4) Remove brake caliper (16) and disk (10) at rear
axle (14). Attach brake caliper with lines connected
in wheel house.
(5) Remove brake shoes (2) of parking brake.
(6) Remove brake control cable lock.
(7) Remove bearing cap bolts (17) and pull axle
shaft out of axle tube (1) (Fig. 6).
(8) Remove seal/gasket.
Fig. 6 AXLE SHAFT
1 - REAR AXLE
11 - BOLT
2 - BRAKE SHOE
12 - WHEEL BOLT
3 - PRESSURE SPRING
13 - BRAKE ADJUSTER
4 - RETURN SPRING
14 - REAR AXLE SHAFT
5 - RETURN SPRING
15 - GASKET
6 - CABLE LOCK
16 - BRAKE CABLE
7 - PARK BRAKE CABLE
17 - BOLT
8 - LOCKING PIN
18 - ABS SENSOR
9 - BOLT
19 - SENSOR BUSHING
10 - BRAKE DISC
VA
REAR AXLE
3 - 23
INSTALLATION - SINGLE REAR WHEEL
(1) Install sealing ring.
(2) Install axle shaft (1) in the axle tube (2) (Fig.
7).
(3) Install new bearing cap (2) bolts (1) and
tighten to 72 N·m (53 ft. lbs.) (Fig. 8).
NOTE: Tighten bolts diagonally across.
(4) Install brake control cable lock.
(5) Install parking brake shoes.
(6) Install brake disk and calipers.
(7) Coat clamping bush with acid-free grease.
Insert ABS sensor with clamping bush fully into the
mounting hole.
(8) Install front brake cable.
(9) Operate brake pedal several times until brake
pads contact brake discs (brake pressure built up).
(10) Install wheels.
BEARING / SEAL - AXLE
REMOVAL
(1) Remove rear axle shaft.
(2) With a punch (2) and hammer straighten bear-
ing (4) nut (1) locking ring (3) (Fig. 9).
(3) Install two wheel mounting bolts into the axle
shaft (1) and clamp in vise. Loosen bearing (4) nut
(2) with Wrench 9279 (3) (Fig. 10).
Fig. 7 AXLE SHAFT AND TUBE
1 - AXLE SHAFT
2 - AXLE TUBE
3 - AXLE BEARINGS
4 - DUST SHIELD
Fig. 8 BEARING CAP BOLTS
1 - BEARING CAP BOLTS
2 - BEARING CAP
3 - AXLE SHAFT FLANGE
Fig. 9 LOCKING RING
1 - BEARING NUT
2 - PUNCH
3 - LOCKING RING
4 - BEARING
Fig. 10 BEARING NUT WRENCH
1 - AXLE SHAFT
2 - BEARING NUT
3 - WRENCH
4 - BEARING
3 - 24
REAR AXLE
VA
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст