Opel Astra Saloon (2017 year). Instruction — part 7
102
Instruments and controls
Using the arrow buttons:
To start, press left arrow button to
select menu item Start and press OK
button to start/stop. To reset, press
left arrow button to select menu item
Reset and press OK button.
Using the left adjuster wheel on the
steering wheel:
To start, select menu item Start and
press to start/stop. To reset, select
menu item Reset and press to confirm
command.
Interruption of power supply
If the power supply has been
interrupted or if the battery voltage
has dropped too low, the values
stored in the trip computer will be lost.
Trip computer in Graphic-
Info-Display or Colour-Info-
Display
The trip computers provide
information on driving data, which is
continually recorded and evaluated
electronically. The trip computer main
page provides information on range,
average consumption and
instantaneous consumption.
To display other trip computer data,
press the BC button on the
Infotainment system and select the
trip computer menu in the display.
The information of the two trip
computers can be reset separately,
making it possible to display different
trip distances.
Graphic-Info-Display,
Colour-Info-Display 3 94.
Range
Range is calculated from current fuel
tank content and instantaneous
consumption. The display shows
average values.
After refuelling, the range is updated
automatically after a brief delay.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Instruments and controls
103
If the fuel in the tank allows less than
50 km of travel, the warning Range
appears on the display.
If the fuel in the tank allows less than
30 km of travel, the warning Refuel!
appears on the display.
Acknowledge the menu item 3 94.
Instantaneous consumption
Display of the instantaneous
consumption.
Display changes depending on
speed:
Display in l/h
: below 13 km/h
Display in
l/100 km
: above 13 km/h
Distance travelled
Display of distance travelled. The
measurement can be reset at any
time.
Average speed
Display of average speed. The
measurement can be reset at any
time.
Stoppages in the journey with the
ignition off are not included in the
calculations.
Effective consumption
Display of the amount of fuel
consumed. The measurement can be
reset at any time.
Average consumption
Display of average consumption. The
measurement can be reset at any
time.
Resetting trip computer
information
Select BC 1 or BC 2 from the trip
computer menu.
Select the desired trip computer
information and reset by pressing the
left adjuster wheel on the steering
wheel or the OK button on the
Infotainment system.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
104
Instruments and controls
To reset all information of a trip
computer, select menu item All
values. After resetting, "- - -" is
displayed for the trip computer
information selected. The
recalculated values are displayed
after a brief delay.
Stop watch
Select menu item Timer from the
Board Computer menu. The Timer
menu is displayed.
To start, select menu item Start. To
reset, select menu item Reset.
The desired stop watch display can
be selected from the Options menu:
Driving Time excl. Stops: The time the
vehicle is in motion is recorded.
Stationary time is not included.
Driving Time incl. Stops: The time the
vehicle is in motion is recorded. The
time the vehicle is stationary with the
key in the ignition switch is included.
Travel Time: Measurement of the
time from instruction activation via Start
to instruction deactivation via Reset.
Interruption of power supply
If the power supply has been
interrupted or if the battery voltage
has dropped too low, the values
stored in the trip computer will be lost.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Lighting
105
Lighting
Exterior lighting . . . . . . .. 105
Light switch . . . . . . . .. 105
Automatic light control . . . . 106
High beam . . . . . . . ... 106
Headlight flash . . . . . . . 106
Headlight range adjustment . 106
Headlights when driving
abroad . . . . . . . . . 107
Daytime running lights . . . . 107
Hazard warning flashers . . .. 107
Turn and lane-change signals . 108
Front fog lights . . . . . . . 108
Rear fog lights . . . . . . . 109
Parking lights . . . . . . ... 109
Reversing lights . . . . . ... 109
Misted light covers . . . . ... 109
Interior lighting . . . . . . ... 110
Instrument panel illumination
control . . . . . . . . . . 110
Interior lights . . . . . . . 110
Load compartment lighting . .. 111
Reading lights . . . . . . .. 111
Sunvisor lights . . . . . . . 112
Lighting features . . . . . . 112
Entry lighting . . . . . . . 112
Exit lighting . . . . . . . .. 112
Battery discharge protection . 113
Exterior lighting
Light switch
Turn light switch:
AUTO : automatic light control:
Headlights are switched on
and off automatically
depending on external
lighting conditions.
7
: off (or deactivation of
automatic light control).
8
: sidelights
9
: headlights
Control indicator C 3 90.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
106
Lighting
Tail lights
Tail lights illuminate together with low
beam/high beam and sidelights.
Automatic light control
When the automatic light control
function is switched on and the
engine is running, low beam switches
on automatically depending on
outside light conditions.
For reasons of safety, the light switch
should always remain in the AUTO
position.
To ensure automatic light control
functions properly, do not cover the
light sensor on top of the instrument
panel.
Driving abroad 3 107.
Wiper activated lighting
With light switch in the AUTO
position, when the windscreen wiper
is operated for 8 cycles or more the
exterior lights illuminate
automatically.
High beam
To switch from low to high beam,
push lever.
To switch to low beam, pull lever back
again.
Control indicator C 3 90.
Headlight flash
To activate the headlight flash, pull
lever.
Headlight range adjustment
Instruction headlight range
adjustment ?
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Lighting
107
With low beam switched on, adapt
headlight range to suit vehicle load.
Correct adjustment of the headlight
range reduces dazzle for other road
users.
Vehicles without automatic level
control system
Turn thumb wheel ? to required
position:
0 : front seats occupied
1 : all seats occupied
2 : all seats occupied and load
compartment laden
3 : driver's seat occupied and load
compartment laden
Vehicles with automatic level control
system
Turn thumb wheel to required
position:
0 : front seats occupied
1 : all seats occupied
1 : all seats occupied and load
compartment laden
2 : driver's seat occupied and load
compartment laden
Automatic level control 3 147.
Automatic headlight range
adjustment
On vehicles with Xenon headlights,
the headlight range is adjusted
automatically based on vehicle load.
If control indicator q illuminates in the
instrument cluster while driving, a
fault has occurred. Have the cause of
the fault remedied immediately by a
workshop.
Control indicator q for Automatic
headlight levelling system 3 90.
Headlights when driving
abroad
The asymmetrical headlight beam
extends visibility at the edge of the
road on the passenger side.
However, when driving in countries
where traffic drives on the opposite
side of the road, have the headlights
adjusted to prevent dazzling of
oncoming traffic. Seek the assistance
of a workshop.
Daytime running lights
Daytime running lights increase
visibility of the vehicle during daylight.
They are switched on automatically
when ignition is on.
Automatic light control 3 106.
Hazard warning flashers
Operated by pressing ¨.
In the event of an accident with airbag
deployment the hazard warning
flashers are activated automatically.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
108
Lighting
Turn and lane-change
signals
lever up
: right turn signal
lever down : left turn signal
If the lever is moved past the
resistance point, the turn signal is
switched on constantly.
When the steering wheel is turned
back, the turn signal is automatically
deactivated. This will not happen
when making a minor steering
manoeuvre such as lane changing.
For three flashes, e.g. when changing
lanes, press the lever until resistance
is felt and then release. Move the
lever to the resistance point and hold
for longer indication.
The volume of the turn signal audible
warning is dependent upon vehicle
speed.
Switch the turn signal off instructionly by
moving the lever to its original
position.
Control indicators O 3 83.
Front fog lights
Operated by pressing >. Control
indicator > 3 90 illuminates in the
instrument cluster when the front fog
lights are switched on.
The front fog lights can only be
switched on when both the ignition
and low beam/high beam or sidelights
are on.
Light switch in position AUTO:
switching on front fog lights will switch
on low beam and sidelights
automatically.
Follow the regulations of the country
in which you are driving when using
front fog lights.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Lighting
109
Rear fog lights
Operated by pressing ø.
Control indicator ø 3 91 illuminates
in the instrument cluster when the
rear fog light is switched on.
The rear fog light can only be
switched on when the ignition is on
and the light switch is in position 9,
or the front fog lights are on and the
light switch is in position 8.
Light switch in position AUTO:
switching on rear fog light will switch
on low beam and sidelights
automatically.
The vehicle rear fog light is
deactivated when towing.
Parking lights
When the vehicle is parked, the
parking lights on one side can be
activated:
1. Set light switch to 7 or AUTO.
2. Switch off ignition.
3. Move turn signal lever all the way
up (right parking lights) or down
(left parking lights).
Confirmed by a signal tone and the
corresponding turn signal control
indicator.
To deactivate, switch on the ignition
or move the turn signal lever in the
opposite direction.
Reversing lights
The reversing lights come on when
the ignition is on and reverse gear is
selected.
Centre high-mounted brake light
Illuminates when the brakes are
applied, acting as a third stop light, to
supplement the brake lights.
Misted light covers
The inside of the light housing may
mist up briefly in poor, wet and cold
weather conditions, in heavy rain or
after washing. The mist disappears
quickly by itself; to help switch on the
headlights.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
110
Lighting
Interior lighting
Instrument panel
illumination control
Brightness of the following lights can
be adjusted when the exterior lights
are on:
● Instrument panel illumination
● Info-Display
● Illuminated switches and
operation elements.
Turn thumb wheel k to the right or left
until the desired brightness is
obtained.
If driver's door is opened or q is
pressed on the remote control,
instrument panel illuminates
automatically for 30 seconds until
ignition switch is turned to position
ACC.
Display mode 3 94.
Interior lights
During entry and exit of the vehicle,
the front and rear courtesy lights
automatically switch on and then off
after a delay.
Note
In the event of an accident with
airbag deployment the courtesy
lights are turned on automatically.
Front courtesy light
Front and rear reading lights and the
load compartment lights function as
courtesy lights and illuminate when
the doors or the tailgate are opened.
If the doors or tailgate remain open,
the lights stay illuminated for
10 minutes. Once all doors and the
tailgate are closed, the courtesy lights
dim gradually after 10 seconds.
By pressing d in the roof console,
both the front and rear reading lights
illuminate. Press again to turn off.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Lighting
111
Courtesy lights can be turned off
immediately by pressing K.
Ignition switch illumination
Illuminates when you open a door.
Switch off immediately by pressing
K
in the roof console.
Glovebox illumination
Illuminates when the glovebox is
opened.
Load compartment lighting
Illuminates when a door or the tailgate
is opened.
Reading lights
Front reading lights
Operated by pressing L and M.
Avoid using front reading lights while
driving in the dark, as they can reduce
driver visibility.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
112
Lighting
Rear reading lights
Left and right rear reading lights are
individually operable. Press to
activate and deactivate.
Sunvisor lights
Illuminates when the vanity mirror
cover is opened 3 33.
Lighting features
Entry lighting
Welcome lighting
Depending upon outside light
conditions, when unlocking the
vehicle with the remote control the
hazard warning lights flash twice and
the exterior and interior lights
illuminate for 20 seconds. This
function facilitates locating the vehicle
when it is dark.
Exit lighting
The low beam and reversing lights
illuminate for 30 seconds after the
driver exits the vehicle and closes the
door.
Switching on
1. Switch off ignition.
2. Remove ignition key.
3. Open driver's door.
4. Pull turn signal lever.
5. Close driver's door.
If the driver's door is not closed the
lights switch off after two minutes.
Exit lighting can be deactivated by
inserting the key in the ignition switch
or by pulling the turn signal lever
again while the driver's door is open.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Lighting
113
Battery discharge protection
To prevent the battery from becoming
discharged, the exterior lights turn off
automatically 10 minutes after the
ignition is switched off.
Battery discharge protection will not
work if the lights are turned on
10 minutes after the ignition has been
switched off; the key cannot be
removed from the ignition switch until
the battery is recharged.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
114
Climate control
Climate control
Climate control systems . . . . 114
Heating and ventilation system 114
Air conditioning system . . ... 115
Electronic climate control
system . . . . . . . . . 116
Air vents . . . . . . . . . . 119
Adjustable air vents . . . . . 119
Fixed air vents . . . . . . . 120
Maintenance . . . . . . . .. 120
Air intake . . . . . . . . . 120
Pollen filter . . . . . . . ... 120
Air conditioning regular
operation . . . . . . . . 121
Service . . . . . . . . . 121
Climate control systems
Heating and ventilation
system
Controls for:
● Temperature
● Air distribution
● Fan speed
● Demisting and defrosting
Heated rear window Ü 3 32.
Heated seats ß 3 40.
Temperature
red : warm
blue : cold
Heating will not be fully effective until
the engine has reached normal
operating temperature.
Air distribution
M
: to head area via adjustable air
vents
L
: to head area via adjustable air
vents and to foot wells
K
: to foot wells and to windscreen
J
: to windscreen, front door
windows and foot wells
l
: to windscreen, front door
windows and head area via
adjustable air vents
All combinations are possible.
Fan speed
Adjust the air flow by switching the fan
to the desired speed.
x
: off
1 : minimum speed
4 : maximum speed
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Climate control
115
Demisting and defrosting
● Set the air distribution switch to
l or J
● Set temperature control to
warmest level
● Set fan to highest level
● Close centre air vents
● Open side air vents and direct
them towards the door windows
Heated rear window Ü 3 32.
Air conditioning system
In addition to the heating and
ventilation system, the air
conditioning system has controls for:
n
: cooling
4
: air recirculation
Ü
: demisting and defrosting
Heated seats ß 3 40.
Cooling n
Press n to switch on cooling.
Activation is indicated by illumination
of the LED in the button. Cooling is
only functional when the engine is
running and climate control fan is
switched on.
Press n again to switch off cooling.
The air conditioning system cools and
dehumidifies (dries) as soon as the
outside temperature is slightly above
freezing point. Therefore
condensation may form and drip from
under the vehicle.
If no cooling or drying is required,
switch the cooling system off to save
fuel.
Activated cooling may inhibit
autostops. Stop-start system 3 126.
Air recirculation system 4
Press 4 to activate air recirculation
mode. Activation is indicated by
illumination of the LED in the button.
Press 4 again to deactivate
recirculation mode.
9 Warning
The exchange of fresh air is
reduced in air recirculation mode.
In operation without cooling the air
humidity increases, so the
windows may mist up from inside.
The quality of the passenger
compartment air deteriorates,
which may cause the vehicle
occupants to feel drowsy.
In warm and very humid ambient air
conditions, the windscreen might mist
up from outside, when cold air is
-------------------------------------------------------------------------------------------------------------------------------------------------------------
116
Climate control
directed towards it. If windscreen
mists up from outside, activate
windscreen wiper and deactivate l.
Maximum cooling
Briefly open the windows and sunroof
so that hot air can disperse quickly.
● Press n to activate air
conditioning.
● Press 4 to activate air
recirculation.
● Set air distribution switch to M.
● Set temperature control to
coldest level.
● Set fan to highest level.
● Open all vents.
Demisting and defrosting
● Set the air distribution switch to
l or J.
● Set temperature control to
warmest level.
● Set fan to highest level.
● Close centre air vents.
● Open side air vents and direct
them towards the door windows.
● Switch on heated rear window Ü
Air conditioning n and air
recirculation 4 are switched on
automatically to improve defrosting
efficiency when position l or J is
selected.
Activated demisting and defrosting
may inhibit autostops. Stop-start
system 3 126.
Electronic climate control
system
The dual zone climate control allows
different climatisation temperatures
for driver and front passenger side.
In automatic mode, temperature, fan
speed and air distribution are
regulated automatically.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Climate control
117
Controls for:
● Temperature on driver side
● Air distribution
● Fan speed
● Temperature on front passenger
side
AUTO : Automatic mode
t
: Automatic air recirculation
V
: Demisting and defrosting
Cooling A/C, Air recirculation 4
Note
Do not cover the interior
temperature sensor (located beside
the fan switch) or the sunlight sensor
(located in front of the windscreen
defroster vents) as this could cause
the system to malfunction.
Heated rear window RÜ 3 32,
Heated seats ß 3 40.
Automatic mode AUTO
Basic setting for maximum comfort:
● Press AUTO; cooling A/C is
switched on and the air
distribution and fan speed are
regulated automatically.
● Open all air vents.
● Set the preselected
temperatures for driver's side
and front passenger's side using
the left and right rotary knobs.
Note
All air vents are actuated
automatically in Automatic mode.
The air vents should therefore
always be open.
Temperature preselection
Recommended comfort setting is
22 °C. Intermediate settings are
possible.
Press SYNC to automatically adjust
front passenger's side temperature to
match current driver's side
temperature. Activation is indicated
by illumination of the LED in the
button.
If temperature settings are different
between driver's side and front
passenger's side, LED in SYNC
button extinguishes.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст