Opel Insignia (2019 year). Instruction — part 11
166
Climate control
Air distribution w x y
Press:
w
: to windscreen and front door
windows
x
: to head area and rear seats via
adjustable air vents
y
: to front and rear foot well and
windscreen
Combinations are possible.
Air conditioning A/C
Press A/C to switch on cooling.
Activation is indicated by the LED in
the button. Cooling is only functional
when the engine is running and
climate control fan is switched on.
Press A/C again to switch off cooling.
The air conditioning system cools and
dehumidifies (dries) as soon as the
outside temperature is slightly above
the freezing point. Therefore
condensation may form and drip from
under the vehicle.
If no cooling or drying is required,
switch off the cooling system for fuel
saving reasons.
Activated cooling may inhibit
Autostops. Stop-start system 3 182.
Demisting and defrosting the
windows á
● Press á: fan automatically
switches to higher speed, the air
distribution is directed towards
the windscreen.
● Set temperature controller
TEMP to warmest level.
● Switch on air conditioning A/C if
required.
● Switch on heated rear window b.
● Switch on heated
windscreen , if available.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Climate control
167
● Open side air vents as required
and direct them towards the door
windows.
● For maximum demisting and
defrosting set fan speed to
highest level.
Note
If á is pressed while the engine is
running, an Autostop will be inhibited
until á is pressed again.
If á is pressed while the engine is in
an Autostop, the engine will restart
automatically.
Stop-start system 3 182.
Air recirculation system n
Press n to activate air recirculation
mode, LED is indicated.
Select air recirculation to assist in
cooling the interior or in blocking
outside odours or exhaust.
Press n again to deactivate air
recirculation mode.
On version without heated
windscreen, press 5 to deactivate
air recirculation. External air mode is
activated.
9 Warning
The exchange of fresh air is
reduced in air recirculation mode.
In operation without cooling the air
humidity increases, so the
windows may mist up from inside.
The quality of the passenger
compartment air deteriorates,
which may cause the vehicle
occupants to feel drowsy.
In warm and very humid ambient air
conditions, the windscreen may mist
up from outside when cold air is
directed towards it. If windscreen
mists up from outside, activate
windscreen wiper and deactivate w.
External air mode 5
Press 5 to activate external air
mode, LED is indicated.
Press n to activate air recirculation
mode. External air mode is
deactivated.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
168
Climate control
Maximum cooling
Briefly open the windows so that hot
air can disperse quickly.
● Switch on air conditioning A/C.
● Press n for air recirculation
system on.
● Press x for air distribution.
● Set temperature control TEMP to
coldest level.
● Set fan speed E to highest level.
● Open all vents.
Version with heated
windscreen ,
If the vehicle is equipped with heated
windscreen, button 5 is replaced by
button ,.
Heated rear window and exterior
mirrors b
Heated windscreen ,
43.
Heated seats q
Electronic climate control
system
The dual zone climate control allows
different temperatures for driver side
and front passenger side.
In automatic mode, temperature, fan
speed and air distribution are
regulated automatically.
Illustration shows functions which
may not be available for your
particular vehicle.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Climate control
169
Controls for:
● Control dial for temperature on
driver side
● Control dial for temperature on
passenger side
● CLIMATE enters the Climate
setting menu in the Info-Display
● Fan speed increase ( and
decrease )
● Climate control ON/OFF or â
● Automatic mode AUTO
● Instruction air recirculation n
● Demisting and defrosting à
● Heated rear window and exterior
mirrors b
● Heated windscreen ,
● Heated seats q
● Ventilated seats r
Activated functions are indicated by
the LED in the respective control.
The electronic climate control system
is only fully operational when the
engine is running.
Climate setting menu CLIMATE
Settings for
● Air distribution w, x, y
● Fan speed E
● Temperature for driver and
passenger side 23°/25°
● Dual zone temperature
synchronisation SYNC
● Air conditioning ON/OFF
can be triggered instructionly in the
Climate setting menu. Press
CLIMATE to enter the menu and
follow the touch buttons.
Climate setting menu can also be
displayed by touching button g in the
Info-Display 3 119.
Changes of settings via the controls
are indicated as pop up in the
Info-Display.
Automatic mode AUTO
Basic settings for automatic control
with maximum comfort:
● Press AUTO, the air distribution
and fan speed are regulated
automatically.
● Open all air vents to allow
optimised air distribution in
automatic mode.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
170
Climate control
● Cooling must be activated in the
climate setting menu for optimal
cooling and demisting. Press
Climate to enter the menu and
follow the touch button to switch
on air conditioning A/C.
● Set the preselected
temperatures separately for
driver and front passenger using
the left and right control dials.
Recommended temperature is
22 °C. Temperature is indicated
briefly in displays beside the
control dials and in the climate
setting menu.
● Air recirculation mode n should
be deactivated. When
deactivated the LED in the button
is not illuminated.
Instruction settings
Climate control system settings can
be changed by activating the
following functions as described
below.
Fan speed ( )
Press upper button ( to increase or
lower button ) to decrease fan speed.
The fan speed is indicated as pop-up
in the Info Display. Fan speed can
also be changed by touch buttons in
the climate setting display. Press
Climate to enter the menu.
Pressing the lower button ) for longer:
fan and cooling are switched off.
To return to automatic mode press
AUTO.
Air distribution w, x, y
Press Climate to enter the menu.
Touch:
w
: to windscreen and front door
windows
x
: to head area and rear seats via
adjustable air vents
y
: to front and rear foot well and
windscreen
To return to automatic air distribution
press AUTO.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Climate control
171
Temperature preselection
Set the preselected temperatures
separately for driver and front
passenger to the desired value using
the left and right control dials. The
knob on the passenger side changes
the temperature for the passenger
side. The knob on the driver's side
changes the temperature for the
driver's side or for both sides
depending on activation of
synchronisation SYNC.
Recommended temperature is 22 °C.
Temperature is indicated in displays
beside the control dials and as pop-
up in the Info-Display.
If the minimum temperature Lo is set,
the climate control system runs at
maximum cooling, if cooling A/C is
switched on.
If the maximum temperature Hi is set,
the climate control system runs at
maximum heating.
Note
If A/C is switched on, reducing the
set cabin temperature can cause the
engine to restart from an Autostop or
inhibit an Autostop.
Dual zone temperature
synchronisation SYNC
Press Climate to enter the menu.
Touch SYNC to link passenger side
temperature setting to the driver side.
When passenger side control dial will
be adjusted, synchronisation is
deactivated.
Air conditioning A/C
Press Climate to enter the menu and
follow the touch button to switch air
conditioning A/C ON or A/C OFF.
Cooling is only functional when the
engine is running and climate control
fan is switched on.
The air conditioning system cools and
dehumidifies (dries) when outside
temperature is above a specific level.
Therefore condensation may form
and drip from under the vehicle.
If no cooling or drying is required,
switch off the cooling system for fuel
saving reasons.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
172
Climate control
Instruction air recirculation n
Press n to activate the air
recirculation mode. The LED in the
button illuminates to indicate
activation.
Press n again to deactivate
recirculation mode.
9 Warning
The exchange of fresh air is
reduced in air recirculation mode.
In operation without cooling the air
humidity increases, so the
windows may mist up from inside.
The quality of the passenger
compartment air deteriorates,
which may cause the vehicle
occupants to feel drowsy.
In warm and very humid ambient air
conditions, the windscreen may mist
up from outside, when cold air is
directed towards it. If windscreen
mists up from outside, activate
windscreen wiper and deactivate w.
Automatic air recirculation
An air humidity sensor switches
automatically to external air if internal
air humidity is too high.
Demisting and defrosting the
windows à
● Press à. The LED in the button
illuminates to indicate activation.
● Temperature and air distribution
are set automatically and the fan
runs at high speed.
● Switch on air conditioning
A/C ON in Climate setting menu
by pressing Climate, if required.
● Switch on heated rear window b.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Climate control
173
● Switch on heated
windscreen , if available.
● To return to previous mode press
à
again, to return to automatic
mode press AUTO.
Note
If à is pressed while the engine is
running, an Autostop will be inhibited
until à is pressed again.
If à is pressed while the engine is in
an Autostop, the engine will restart
automatically.
Stop-start system 3 182.
Deactivation or activation of
Electronic climate control system
ON/OFF
Cooling, fan and automatic mode can
be switched off by pressing ON/OFF.
When the system is deactivated, the
LED in the button ON/OFF is not
illuminated.
Activation by pressing ON/OFF again
or AUTO. The LED in the button
illuminates to indicate activation.
Version with heated
windscreen ,
If the vehicle is equipped with heated
windscreen, button ON/OFF is
replaced by button ,.
Climate control system will then
switched off by button â. Switch on
by pressing (.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
174
Climate control
Basic settings
Following settings can be changed in
the Personalisation menu in the
Info-Display:
● fan speed regulation in automatic
mode.
● settings of automatic rear window
heating.
● settings of automatic windscreen
dehumidification
● settings of automatic seat
heating
Vehicle personalisation 3 124.
Heated rear window and exterior
mirrors b
Heated windscreen ,
Heated seats q
Ventilated seats r
Auxiliary heater
Air heater
Quickheat is an electric auxiliary air
heater which automatically warms up
the passenger compartment more
quickly.
Air vents
Adjustable air vents
At least one air vent must be open
while cooling is on.
Illustration shows centre air vents in
instrument panel.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Climate control
175
Illustration shows outer air vents in
instrument panel.
Illustration shows air vents for rear
passenger.
Direct the flow of air by tilting and
swivelling the slats.
To close the vent, swivel the slat
sideways.
9 Warning
Do not attach any objects to the
slats of the air vents. Risk of
damage and injury in case of an
accident.
Fixed air vents
Additional air vents are located
beneath the windscreen and door
windows and in the foot wells.
Maintenance
Air intake
The air intake in front of the
windscreen in the engine
compartment must be kept clear to
allow air intake. Remove any leaves,
dirt or snow.
Cabin air filter
Change filter regulary for maximum
effect.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
176
Climate control
Air conditioning regular
operation
In order to ensure continuously
efficient performance, cooling must
be operated for a few minutes once a
month, irrespective of the weather
and time of year. Operation with
cooling is not possible when the
outside temperature is too low.
Service
For optimal cooling performance, it is
recommended to annually check the
climate control system, starting
three years after initial vehicle
registration, including:
● functionality and pressure test
● heating functionality
● leakage check
● check of drive belts
● cleaning of condenser and
evaporator drainage
● performance check
● cabin air filter check
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Driving and operating
177
Driving and
operating
Driving hints . . . . . . . ... 178
Control of the vehicle . . . ... 178
Steering . . . . . . . . ... 178
Starting and operating . . . ... 178
New vehicle running-in . . . 178
Power button . . . . . . ... 179
Retained power off . . . . .. 180
Starting the engine . . . . .. 180
Overrun cut-off . . . . . . 182
Stop-start system . . . . . 182
Parking . . . . . . . . . 184
Engine exhaust . . . . . . .. 185
Exhaust filter . . . . . . . 185
Catalytic converter . . . . ... 186
AdBlue . . . . . . . . . . 187
Automatic transmission . . . .. 189
Instruction transmission . . . . .. 194
Drive systems . . . . . . . 194
All-wheel drive . . . . . . . 194
Brakes . . . . . . . . . . 195
Antilock brake system . . . . 195
Parking brake . . . . . . .. 196
Brake assist . . . . . . . . 197
Hill start assist . . . . . . . 197
Ride control systems . . . . . 198
Traction Control system . . .. 198
Electronic Stability Control . .. 199
Interactive driving system . . 201
Driver assistance systems . . . 203
Cruise control . . . . . . .. 203
Speed limiter . . . . . . ... 204
Adaptive cruise control . . . 206
Forward collision alert . . . . 216
Following distance indication ... 219
Active emergency braking . ... 220
Front pedestrian protection . . 223
Parking assist . . . . . . .. 225
Side blind spot alert . . . . . 231
Lane change alert . . . . . 233
Panoramic view system . . ... 234
Rear view camera . . . . ... 237
Rear cross traffic alert . . . . 238
Traffic sign assistant . . . . 240
Lane keep assist . . . . . . 244
Fuel . . . . . . . . . . . 246
Fuel for petrol engines . . . . 246
Fuel for diesel engines . . . 248
Refuelling . . . . . . . . 248
Trailer hitch . . . . . . . . 250
General information . . . . . 250
Driving characteristics and
towing tips . . . . . . . .. 251
Trailer towing . . . . . . ... 251
Towing equipment . . . . ... 252
Trailer stability assist . . . ... 253
-------------------------------------------------------------------------------------------------------------------------------------------------------------
178
Driving and operating
Driving hints
Control of the vehicle
Never coast with engine not
running
Many systems will not function in this
situation (e.g. brake servo unit, power
steering). Driving in this manner is a
danger to yourself and others.
All systems function during an
Autostop.
Stop-start system 3 182.
Idle boost
If charging of the vehicle battery is
required due to battery condition, the
power output of the generator must
be increased. This will be achieved by
an idle boost which may be audible.
A message appears in the Driver
Information Centre.
Pedals
To ensure the pedal travel is
uninhibited, there must be no mats in
the area of the pedals.
Use only floor mats, which fit properly
and are fixed by the retainers on the
driver side.
Steering
If power steering assist is lost
because the engine stops or due to a
system malfunction, the vehicle can
be steered but may require increased
effort.
Starting and operating
New vehicle running-in
Do not brake unnecessarily hard for
the first few journeys.
During the first drive, smoke may
occur because of wax and oil
evaporating off the exhaust system.
Park the vehicle in the open for a
while after the first drive and avoid
inhaling the fumes.
During the running-in period, fuel and
engine oil consumption may be
higher.
Additionally, the cleaning process of
the exhaust filter may take place more
often.
Exhaust filter 3 185.
Autostop may be inhibited to allow for
charging of the vehicle battery.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Driving and operating
179
Power button
Electronic key must be inside the
vehicle.
Accessory power mode
Press Engine Start/Stop once without
operating clutch or brake pedal. The
yellow LED in the button illuminates.
Steering wheel lock is released and
some electrical functions are
operable, ignition is off.
Ignition on power mode
Press and hold Engine Start/Stop for
six seconds without operating clutch
or brake pedal. The green LED in the
button illuminates, diesel engine is
preheating. Control indicators
illuminate and most electrical
functions are operable.
Engine start
Press Engine Start/Stop briefly while:
● instruction transmission: operating
clutch pedal,
● automatic transmission:
operating brake pedal with
selector lever in P or N.
Starting the engine 3 180.
Ignition off
Press Engine Start/Stop briefly when
Autostop is activated or when engine
is running and vehicle is stationary.
Automatic transmission: apply the
parking brake and engage P.
Press Engine Start/Stop briefly
without operating clutch or brake
pedal when in ignition on power
mode.
Some functions remain active until
driver's door is opened, provided the
ignition was on previously.
Emergency engine shut off during
driving
Press Engine Start/Stop for more
than two seconds or press twice
briefly within five seconds 3 180.
Steering wheel lock
The steering wheel lock activates
automatically when:
● The vehicle is stationary.
● The ignition has been switched
off.
● The driver's door is opened.
To release steering wheel lock, open
and close driver's door and switch on
accessory mode or start the engine
directly.
9 Warning
If the vehicle battery is discharged,
the vehicle must not be towed,
tow-started or jump-started as the
steering wheel lock cannot be
disengaged.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
180
Driving and operating
Operation on vehicles with
electronic key system in case of
failure
If either the electronic key fails or the
battery of the electronic key is weak,
the Driver Information Centre may
display No Remote Detected or
Replace Battery in Remote Key when
you try to start the vehicle.
Open the cover of the centre console
in front of the gear shift lever. Place
the electronic key across with buttons
upside in the transmitter pocket
beside the power outlet, as shown in
the illustration.
Other objects, e.g. other keys,
transponder, tags, coins etc. must be
removed from the pocket.
Depress the clutch pedal (manual
transmission), the brake pedal and
press Engine Start/Stop. Release the
button after starting procedure
begins.
To switch off the engine, press
Engine Start/Stop again. Remove the
electronic key from the transmitter
pocket.
This option is intended for
emergencies only. Replace the
electronic key battery as soon as
possible 3 22.
For unlocking or locking the doors,
see fault in electronic key system
Retained power off
The following electronic systems can
work until the driver's door is opened
or for 10 minutes after the ignition is
switched off:
● power windows
● sunroof
● power outlets
Starting the engine
Vehicles with power button
Manual transmission: operate clutch
and brake pedal.
Automatic transmission: operate
brake pedal and move selector lever
to P or N.
Do not operate accelerator pedal.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Driving and operating
181
Press Engine Start/Stop briefly: an
automatic procedure operates the
starter with a short delay until the
engine is running.
To switch off the engine when vehicle
is stationary, press
Engine Start/Stop briefly. Automatic
transmission: apply the parking brake
and engage P.
To start the engine during an
Autostop:
Manual transmission: during an
Autostop, the engine can be started
by depressing the clutch pedal
182.
Automatic transmission: during an
Autostop, the engine can be started
by releasing the brake pedal 3 182.
Emergency engine shut off during
driving
If the engine needs to be switched off
during driving in case of emergency,
press Engine Start/Stop for more than
two seconds or press twice briefly
within five seconds.
9
Danger
Switching off the engine during
driving may cause loss of power
support for brake and steering
systems. Assistance systems and
airbag systems are disabled.
Lighting and brake lights will
extinguish. Therefore power down
the engine and ignition while
driving only when required in case
of emergency.
Starting the vehicle at low
temperatures
Starting the engine without additional
heaters is possible down to -25 °С for
diesel engines and -30 °C for petrol
engines. Required is an engine oil
with the correct viscosity, the correct
fuel, performed services and a
sufficiently charged vehicle battery.
With temperatures below -30 °C the
automatic transmission requires a
warming phase of approx.
five minutes. The selector lever must
be in position P.
Automatic Starter Control
This function controls the engine
starting procedure. The driver does
not need to hold Engine Start/Stop
pressed. Once applied, the system
will go on starting automatically until
the engine is running. Because of the
checking procedure, the engine starts
running after a short delay.
Possible reasons for a non-starting
engine:
● Clutch pedal not operated
(manual transmission).
● Brake pedal not operated or
selector lever not in P or N
(automatic transmission).
● Timeout occurred.
Turbo engine warm-up
Upon start-up, engine available
torque may be limited for a short time,
especially when the engine
temperature is cold. The limitation is
to allow the lubrication system to fully
protect the engine.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст