Opel Combo (2018 year). Instruction — part 6
86
Instruments and controls
s
illuminates during driving when a
fault is present in the transmission.
A warning message may also appear
in the Driver Information Centre
91 in conjunction with a warning
chime.
Continued driving is possible,
provided the vehicle is driven with
care and anticipation.
Have the cause of the fault remedied
by a workshop as soon as possible.
Instruction transmission automated
Gear shifting
[
or Ò illuminates green in the
Driver Information Centre 3 91
when gearshifting is recommended
for fuel saving reasons.
Hill start assist
Z
illuminates yellow.
Illuminates for a few seconds after the
ignition is switched on.
If the control indicator does not
extinguish after a few seconds, or if it
illuminates while driving, there is a
fault in the Hill start assist. Seek the
assistance of a workshop to have the
fault remedied.
The Electronic Stability Control (ESC)
control indicator R may also
illuminate 3 86 in conjunction with
Z
.
Depending on version, 9 may
illuminate as an alternative if control
indicator Z is not present. A
corresponding warning message,
e.g. Hill holder unavailable, may also
be displayed in the Driver Information
Centre 3 91.
Generic warning 9 3 82.
Hill start assist 3 128.
Ultrasonic parking assist
r illuminates yellow.
Fault in system
or
Fault due to sensors that are dirty or
covered by ice or snow
or
Interference due to external sources
of ultrasound. Once the source of
interference is removed, the system
will operate normally.
Have the cause of the fault in the
system remedied by a workshop.
Control indicator 9 will illuminate as
an alternative if control indicator r
is not present. Depending on version,
a corresponding warning message,
e.g. Parking help unavailable, may
also be displayed in the Driver
Information Centre 3 91.
Generic warning 9 3 82.
Ultrasonic parking assist 3 132.
Electronic Stability Control
R
illuminates or flashes yellow.
Illuminates for a few seconds after the
ignition is switched on. The system is
ready for operation when the control
indicator extinguishes.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Instruments and controls
87
Flashes during driving
The system is actively engaged.
Engine output may be reduced and
the vehicle may be braked
automatically to a small degree.
Illuminates during driving
A fault in the system is present.
Continued driving is possible. Driving
stability, however, may deteriorate
depending on road surface
conditions.
Have the cause of the fault remedied
by a workshop.
Depending on version, a
corresponding warning message,
e.g. ESP unavailable, may also be
displayed in the Driver Information
Centre 3 91.
Electronic Stability Control (ESC)
Traction control system/Anti-Slip
Regulator (ASR) 3 129.
Engine coolant temperature
$
illuminates red.
Illuminates for a few seconds after the
ignition is switched on.
If control indicator $ illuminates, the
coolant temperature is too high.
Depending on version, a warning
message may also be displayed in
the Driver Information Centre 3 91.
Seek the assistance of a workshop.
Caution
If engine coolant temperature is
too high, stop vehicle, switch off
the ignition. Danger to engine.
Check coolant level.
If the control indicator remains on,
seek the assistance of your
workshop.
Engine coolant temperature gauge
Preheating
!
illuminates yellow.
Preheating of diesel engine is
activated. Only activates when
outside temperature is low.
Note
In very hot outside
temperatures, ! may illuminate
briefly when the ignition is switched
on.
The engine can be started when !
extinguishes.
Starting the engine 3 116.
Flashes
A fault is detected in the engine
preheating system. Depending on
version, a corresponding warning
message, e.g. Check glow plugs,
may also be displayed in the Driver
Information Centre 3 91.
If ! does not extinguish, consult a
workshop.
Diesel particle filter
%
illuminates yellow.
Illuminates for a few seconds after the
ignition is switched on.
If it does not extinguish after a brief
delay or illuminates whilst driving, the
diesel particle filter requires cleaning.
Continue driving until %
-------------------------------------------------------------------------------------------------------------------------------------------------------------
88
Instruments and controls
extinguishes. Depending on version,
a warning message may also be
displayed in the Driver Information
Centre 3 91.
If possible, do not allow engine speed
to drop below 2000 rpm during the
cleaning process.
Control indicator % illuminates when
diesel particle filter is full. Start
cleaning process as soon as possible
to avoid damage to the engine.
Diesel particle filter 3 121.
Stop-start system 3 117.
Tyre pressure monitoring
system
w illuminates or flashes yellow.
Illuminates
Tyre pressure loss. Stop immediately
and check tyre pressure.
Control indicator w illuminates
together with a warning chime and, in
vehicles with Multifunction version of
the Driver Information Centre 3 91,
a corresponding message also
appears when a puncture or severely
under-inflated tyre is detected.
Flashes
Fault in system. After several
seconds w illuminates continuously.
Consult a workshop.
Depending on version, a
corresponding message also
appears in the Driver Information
Centre when a tyre without a pressure
sensor is mounted (e.g. spare wheel).
Tyre pressure monitoring system
Engine oil pressure
I
illuminates red.
Illuminates when the ignition is
switched on and extinguishes shortly
after the engine starts.
Illuminates when the engine is
running
Depending on version, a warning
message may also be displayed in
the Driver Information Centre 3 91.
Caution
Engine lubrication may be
interrupted. This may result in
damage to the engine and/or
locking of the drive wheels.
1. Depress clutch.
2. Select neutral gear (or move
selector lever to N).
3. Move out of the flow of traffic as
quickly as possible without
impeding other vehicles.
4. Switch off ignition.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Instruments and controls
89
9 Warning
When the engine is off,
considerably more force is needed
to brake and steer. During an
Autostop the brake servo unit will
still be operational.
Do not remove ignition key until
vehicle is stationary, otherwise the
steering wheel lock could engage
unexpectedly.
Check oil level before seeking the
assistance of a workshop 3 144.
Change engine oil
Diesel engines with diesel particle
filter
I
flashes red.
Illuminates when the ignition is
switched on and extinguishes shortly
after the engine starts.
The engine oil life monitor lets you
know when to change the oil. Control
indicator I will flash to indicate that
engine oil life has been diminished
and the oil needs changing.
Depending on version, a
corresponding warning message,
e.g. Change engine oil, may also be
displayed in the Driver Information
Centre 3 91.
Based on driving conditions, the
interval at which an oil change will be
indicated can vary considerably.
Depending on model variant, I may
flash in the following ways:
● for one minute every two hours,
or
● for three minute cycles with I off
for intervals of five seconds
The warning will be repeated every
time the engine is started, until the
engine oil is changed and the service
display is reset. Seek the assistance
of a workshop.
Service display 3 79.
Low engine oil level
S
illuminates red.
Illuminates for a few seconds after the
ignition is switched on.
If the control indicator does not
extinguish after a few seconds, or if it
illuminates while driving, the engine
oil level is insufficient.
Depending on version, a
corresponding warning message,
e.g. Check engine oil level, may also
be displayed in the Driver Information
Centre 3 91.
Check oil level before seeking the
assistance of a workshop 3 144.
Low fuel
$
illuminates or flashes yellow.
Illuminates for a few seconds after the
ignition is switched on.
Illuminates
Level in fuel tank is too low. Refuel
immediately 3 136.
Never run the tank dry.
Depending on version, a
corresponding warning message,
e.g. Warning low fuel, may also be
displayed in the Driver Information
-------------------------------------------------------------------------------------------------------------------------------------------------------------
90
Instruments and controls
Flashes
Fault in fuel system. Have the cause
of the fault remedied by a workshop.
The needle in the fuel gauge will point
Drain fuel filter
U
illuminates yellow.
Illuminates for a few seconds after the
ignition is switched on.
Illuminates when the engine is
running
Indicates the presence of water in the
diesel.
Depending on version, a
corresponding warning message,
e.g. Check diesel fuel filter, may also
be displayed in the Driver Information
Centre 3 91. Seek the assistance of
a workshop immediately.
Immobiliser
d
illuminates yellow.
If d illuminates when starting, there
is a fault in the immobiliser system.
The engine cannot be started.
Depending on version, a warning
message may also be displayed in
the Driver Information Centre 3 91.
Seek the assistance of a workshop.
Immobiliser 3 29.
Stop-start system
Æ
illuminates yellow.
A fault is present in the system. Have
the cause of the fault remedied by a
workshop.
Control indicator 9 will illuminate as
an alternative if control indicator Æ is
not present.
Depending on version, a
corresponding warning message,
e.g. Start&Stop unavailable, may also
be displayed in the Driver Information
Centre 3 91.
Generic warning 9 3 82.
Stop-start system 3 117.
Exterior light
8
illuminates green.
The exterior lights are on 3 100.
Control indicator 8 also illuminates
when the exit lighting feature has
Exterior light failure
µ
illuminates yellow.
Failure of one or more of the exterior
lights or associated fuse.
Control indicator 9 will illuminate as
an alternative if µ is not present.
Depending on version, a warning
message may also be displayed in
the Driver Information Centre 3 91.
Generic warning 9 3 82.
Bulb replacement 3 149.
High beam
C illuminates blue.
Illuminated when high beam is on and
during headlight flash 3 100.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Instruments and controls
91
Fog light
>
illuminates green.
The front fog lights are on 3 102.
Rear fog light
ø
illuminates yellow.
The rear fog light is on 3 102.
Cruise control
m
illuminates green.
The system is switched on.
Depending on version, a
corresponding message, e.g. Cruise
Control on, may also be displayed in
the Driver Information Centre 3 91.
Cruise control 3 131.
Door open
( illuminates red.
Illuminates when a door, the bonnet
or the tailgate is open.
Depending on version, a warning
message may also be displayed in
the Driver Information Centre 3 91.
When the vehicle starts to move, a
warning chime also sounds.
Information displays
Driver Information Centre
The Driver Information Centre is
located in the instrument cluster
between the speedometer and
tachometer. Two versions are
available.
Standard version is shown in the
illustration above.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
92
Instruments and controls
Multifunction version, with further
adjustable settings, is shown in the
illustration above.
Some of the displayed functions differ
when the vehicle is being driven or at
a standstill. Some options are only
available when the vehicle is being
driven.
Depending on version, the following
items may appear in the display:
● odometer, trip odometer 3 77
● clock 3 73
● outside temperature 3 73,
● headlight range adjustment
● transmission display 3 123
● stop-start system indicator
● vehicle messages 3 96
● trip computer 3 97
Selecting menus and options
The menus and options can be
selected via the buttons on the
instrument panel.
Press SETq once to access the
settings menu.
Press R or S to scroll through the
menu options and press SETq again
to access a displayed menu option.
Press R or S to scroll through the
available settings or to increase/
decrease the displayed value.
Press and hold R or S to increase/
decrease a value rapidly (press again
to stop on the required value).
After all changes have been made,
briefly press SETq again to confirm
changes and automatically return to
the previous display screen.
Alternatively, press and hold SETq
to return to the previous display
screen without saving changes to the
current menu option.
Note
The settings menu is exited
automatically after a delay. Only
changes already confirmed by
briefly pressing SETq are stored.
Settings menu options - Standard
version
The settings menu contains the
following options:
● ILLU
● SPEEd
● HOUR
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Instruments and controls
93
● UNIT
● bUZZ
● BAG P
● DRL
ILLU (Brightness of interior lighting)
When driving at night with the low
beam on, adjust the brightness of the
vehicle's interior lighting (e.g.
instrument panel, climate control
display).
SPEEd (Speed limit warning chime)
Activate or deactivate the speed limit
warning chime or change the speed
limit. Speeds between 30 and
200 km/h can be stored.
When activated, the driver is alerted
with a warning chime when the set
speed limit is exceeded.
After accessing this menu option,
activate or deactivate the function
(set to On or Off) and confirm.
Press SETq when activated (On) to
access the current set speed. Adjust
as required and confirm.
Warning chimes 3 96.
HOUR (Setting the clock)
Adjust the hours setting (flashing
value) and confirm. Adjust minutes
setting (flashing value) and confirm.
Clock 3 73.
UNIT (Unit of measurement)
Set the unit of measurement to km or
miles.
bUZZ (Warning chime volume)
Adjust the volume of warning chimes
and confirm. eight volume levels are
available.
A chime is also sounded every time
SETq, R or S is pressed.
Warning chimes 3 96.
BAG P (Passenger front and side
airbags activation/deactivation)
Activate the front passenger airbags
if an adult is occupying the front
passenger seat. Deactivate airbags
when a child restraint system is
installed on this seat.
9 Danger
Risk of fatal injury for a child using
a child restraint system on a seat
with activated front passenger
airbag.
Risk of fatal injury for an adult
person on a seat with deactivated
front passenger airbag.
After accessing this menu option,
activate or deactivate the airbags
(BAG P On or BAG P Off) and
confirm; a confirmation message
appears in the display. Select YES (to
confirm changes) or No (to cancel
changes).
Airbag deactivation 3 53.
DRL (Daytime running lights)
Activate the daytime running lights to
increase visibility of the vehicle during
daylight (set to On). Deactivate when
not required (set to Off).
Daytime running lights 3 101.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
94
Instruments and controls
Settings menu options -
Multifunction version
The settings menu contains the
following options:
● Dimmer
● Speed beep
● TripB data
● Set time
● Set date
● See radio (or Radio info)
● Autoclose
● Units (or Unit of measurement)
● Language
● Buzzer volume (or Warning
volume)
● Button vol. (or Button volume)
● Belt buzzer (or Seat belt buzzer)
● Service
● Passenger bag (or Passenger
airbag)
● Day lights (or Daytime running
lights)
● Exit Menu
Dimmer (Brightness of interior
lighting)
When driving at night with the low
beam on, adjust the brightness of the
vehicle's interior lighting (e.g.
instrument panel, climate control
display).
Depending on version, it may also be
possible to adjust the brightness by
pressing R or S without accessing
the settings menu.
Speed beep (Speed limit warning
chime)
Activate or deactivate the speed limit
warning chime or change the speed
limit. Speeds between 30 and
200 km/h can be stored.
When activated, the driver is alerted
with a warning chime when the set
speed limit is exceeded.
After accessing this menu option,
activate or deactivate the function
(set to On or Off) and confirm.
Press SETq when activated (On) to
access the current set speed. Adjust
as required and confirm.
Warning chimes 3 96.
TripB data
Activate or deactivate the second trip
computer (set to On or Off).
Trip B records average consumption,
distance travelled, average speed
and travel time (driving time). The
measurement can be restarted at any
time. Trip computer 3 97.
Set time (Setting the clock and clock
mode)
After accessing this menu option, it is
possible to either set the time or
change the clock mode between 12
hour and 24 hour clock.
Select Time and confirm. Adjust the
hours setting (flashing value) and
confirm. Adjust minutes setting
(flashing value) and confirm.
Select Mode and confirm. Select
12h or 24h and confirm.
Clock 3 73.
Set date
Adjust the year setting (flashing
value) and confirm. Adjust month
setting (flashing value) and confirm.
Adjust the day setting (flashing value)
and confirm.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Instruments and controls
95
See radio or Radio info (Display audio
and radio information)
Available depending on version,
activate radio info (set to On) to
display audio and radio information
(e.g. station frequency, RDS
messages, track number). Deactivate
when not required (set to Off).
Autoclose (Automatic central locking
when driving)
Activate the autoclose feature (set to
On) to automatically lock the doors
when vehicle speed exceeds
20 km/h. Deactivate when not
required (set to Off).
Units or Unit of Measurement (for
Distance, Fuel consumption and
Temperature)
After accessing this menu option, it is
possible to set the unit of
measurement for distance, fuel
consumption and temperature.
Select Distance and confirm. Set the
unit of measurement to km or mi
(miles) and confirm.
Select Consumption and confirm.
When the Distance unit is set to km, it
is possible to set the unit of
measurement for fuel consumption to
either l/100km or km/l. When the
Distance unit is set to mi (miles), fuel
consumption is shown in mpg.
Select Temperature and confirm. Set
the unit of measurement to °C or °F
and confirm.
Language
Languages selectable include:
English, German, French, Italian,
Portuguese, Spanish, Dutch, Polish
and Turkish. Select desired language
and confirm.
Buzzer volume or Warning volume
(Warning chime volume)
Adjust the volume of warning chimes
and confirm. eight volume levels are
available.
Warning chimes 3 96.
Button vol. or Button volume
A chime is sounded every time
SETq, R or S is pressed.
Adjust the volume of these chimes
and confirm. eight volume levels are
available.
Warning chimes 3 96.
Belt buzzer or Seat belt buzzer
(Reactivate warning chime for driver
and/or front passenger seat belt
reminder)
This menu option is available only if
the seat belt reminder is not active.
When reactivated, the driver and/or
front passenger are alerted with a
warning chime when the
corresponding seat belt is not
fastened.
Seat belt reminder 3 83.
Service (Distance to next service)
Access this menu option to view the
remaining distance to the next service
(available depending on version).
The distance to next service is also
displayed automatically when the
distance reaches 2,000 km and is
repeated after every additional
200 km.
Service display 3 79.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
96
Instruments and controls
Passenger bag or Passenger airbag
(Passenger front and side airbags
activation/deactivation)
Activate the front passenger airbags
if an adult is occupying the front
passenger seat. Deactivate airbags
when a child restraint system is
installed on this seat.
9 Danger
Risk of fatal injury for a child using
a child restraint system on a seat
with activated front passenger
airbag.
Risk of fatal injury for an adult
person on a seat with deactivated
front passenger airbag.
After accessing this menu option,
activate or deactivate the airbags
(Bag Pass On or Bag Pass Off) and
confirm; a confirmation message
appears in the display. Select YES (to
confirm changes) or No (to cancel
changes).
Airbag deactivation 3 53.
Day lights or Daytime running lights
Activate the daytime running lights to
increase visibility of the vehicle during
daylight (set to On). Deactivate when
not required (set to Off).
Daytime running lights 3 101.
Exit Menu
Select this menu option to exit the
settings menu.
Vehicle messages
Warning chimes
Only one warning chime will sound at
a time.
The warning chime regarding
unfastened seat belts has priority
over any other warning chime.
When starting the engine or whilst
driving
● If seat belt is not fastened.
● If a certain speed is exceeded
with the parking brake applied.
● If the parking assist detects an
object.
● If a fault is detected in the parking
assist.
● If a door, the bonnet or the
tailgate is not fully closed when
starting-off.
● If the vehicle speed briefly
exceeds a set limit.
● If the stop-start system cannot
restart the engine automatically.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Instruments and controls
97
● Vehicles with manual
transmission automated; brake
pedal has not been depressed
when starting the engine.
● Vehicles with manual
transmission automated; an
incorrect gear has been selected
when starting-off or during
driving.
● Vehicles with manual
transmission automated; when
the vehicle is at a standstill, if
engine is running and a gear is
engaged; transmission
automatically shifts to N in certain
situations.
● If the clutch temperature is too
high in vehicles with manual
transmission automated.
● If a transmission fault is detected
in vehicles with manual
transmission automated.
● If a warning message, e.g. low
tyre pressure, appears in the
Driver Information Centre.
When the vehicle is parked
and/or the driver's door is opened
● When the key is in the ignition
switch.
Fuel system messages
Fuel cut-off system
In the event of a collision of a certain
severity, the fuel system is cut-off and
the engine is switched off
automatically, for safety reasons.
Control indicator 9 3 82 illuminates if
the fuel cut-off switch is triggered and,
depending on version, a
corresponding warning message may
also appear in the Driver Information
Centre 3 91.
To reset the fuel cut-off system and
enable the vehicle to be driven, refer
to "Vehicle shutdown" 3 116.
Trip computer
The trip computer provides
information on driving data, which is
continually recorded and evaluated
electronically.
Depending on version, the following
functions may be selected by
pressing TRIP repeatedly on the end
of the wiper lever:
Standard version
● outside temperature (if available)
● range
● distance travelled
-------------------------------------------------------------------------------------------------------------------------------------------------------------
98
Instruments and controls
● average consumption
● instantaneous consumption
● average speed
● travel time (driving time)
Multifunction version
Two trip odometers, Trip A and Trip
B, are available for selection and are
recorded separately.
The information of the two trip
computers can be reset separately,
making it possible to display different
trip distances.
Trip A
● range
● distance travelled
● average consumption
● instantaneous consumption
● average speed
● travel time (driving time)
Trip B
● distance travelled
● average consumption
● average speed
● travel time (driving time)
Trip B can be deactivated via the
Driver Information Centre 3 91.
Reset trip computer information
To reset the trip computer, select one
of its functions, then press and hold
TRIP for a few seconds.
The following trip computer
information will be reset:
● average consumption
● distance travelled
● average speed
● travel time (driving time)
A confirmation message appears in
the display when the trip computer is
reset.
Note
The trip computer will reset
automatically when the maximum
value of any of the parameters is
exceeded.
Outside temperature
The temperature outside the vehicle
is displayed (depending on version).
Outside temperature 3 73, 3 91.
Range
The range is calculated from the
current contents of the fuel tank and
the average consumption since the
last reset.
When the range is less than 50 km,
_ _ _ _ will appear in the display.
After refuelling, the range is updated
automatically after a brief delay.
The measurement can be restarted at
any time.
Note
The range will not be displayed if the
vehicle is left parked with the engine
running for a long time.
Distance travelled
Displays the distance driven since the
last reset.
The measurement can be restarted at
any time.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Instruments and controls
99
Average consumption
Average consumption is displayed,
taking into consideration the distance
travelled and the fuel used since the
last reset.
The measurement can be restarted at
any time.
Instantaneous consumption
Display of the instantaneous fuel
consumption.
_ _ _ _ will appear in the display if the
vehicle is left parked with the engine
running for a long time.
Average speed
The average speed since the last
reset is displayed.
The measurement can be restarted at
any time.
Interruptions in the journey with the
ignition off are not included in the
calculations.
Travel time (driving time)
The time elapsed since the since the
last reset is displayed.
The measurement can be restarted at
any time.
Exit trip computer
To exit the trip computer, press and
hold SETq for more than
two seconds.
Driver Information Centre 3 91.
Interruption of power supply
If the power supply has been
interrupted or if the vehicle battery
voltage has dropped too low, the
values stored in the trip computer will
be lost.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
100
Lighting
Lighting
Exterior lighting . . . . . . .. 100
Light switch . . . . . . . .. 100
High beam . . . . . . . ... 100
Headlight flash . . . . . . . 100
Headlight range adjustment . 101
Headlights when driving
abroad . . . . . . . . . 101
Daytime running lights . . . . 101
Hazard warning flashers . . .. 101
Turn and lane-change signals . 102
Front fog lights . . . . . . . 102
Rear fog lights . . . . . . . 102
Reversing lights . . . . . ... 103
Misted light covers . . . . ... 103
Interior lighting . . . . . . ... 103
Instrument panel illumination
control . . . . . . . . . . 103
Interior lights . . . . . . . 104
Load compartment lighting . .. 105
Lighting features . . . . . . 106
Exit lighting . . . . . . . .. 106
Battery discharge protection . 106
Exterior lighting
Light switch
Turn light switch:
§
: off / daytime running lights
9
: sidelights / headlights
Control indicator 8 3 90.
Tail lights
Tail lights are illuminated together
with low/high beam and sidelights.
High beam
To switch from low to high beam,
push lever. To switch to low beam,
pull lever.
Depending on version, pull lever
towards steering wheel to switch
between high and low beam.
Headlight flash
To activate the headlight flash, pull
lever.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Lighting
101
Headlight range adjustment
Manual headlight range
adjustment
To adapt headlight range to the
vehicle load to prevent dazzling of
other road users: Press À or Á until
the required setting is displayed in the
Driver Information Centre 3 91.
0 : front seats occupied
1 : all seats occupied
2 : all seats occupied and load
compartment laden
3 : driver's seat occupied and load
compartment laden
Headlights when driving
abroad
The asymmetrical headlight beam
extends visibility at the edge of the
road at the passenger side.
However, when driving in countries
where traffic drives on the opposite
side of the road, adjust the headlights
to prevent dazzling of oncoming
traffic.
Have the headlights adjusted by a
workshop.
Daytime running lights
Daytime running lights increase
visibility of the vehicle during daylight.
When the function is activated and
the ignition is switched on, the
headlights come on automatically and
instrument illumination is subdued.
The light switch must be in position
§
. The daytime running lights switch
off when the ignition is switched off.
Note
The driver remains responsible for
switching on the low beam when
required, e.g. when driving through
a tunnel or at night.
The daytime running lights function is
activated/deactivated via a menu in
the Driver Information Centre 3 91.
When the function is deactivated, the
headlights do not come on
automatically when the ignition is
switched on and the light switch is in
position §.
Hazard warning flashers
Operated by pressing ¨.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст