Opel Movano (2018 year). Instruction — part 7
Instruments and controls
103
Information displays
Driver Information Centre
The Driver Information Centre is
located in the instrument cluster
below the speedometer.
Depending on vehicle configuration,
the following items appear in the
display:
● outside temperature 3 87
● clock 3 88
● odometer, trip odometer 3 91
● engine oil level monitor 3 93
● service display 3 93
● vehicle messages 3 104
● trip computer 3 105
Some of the displayed functions differ
when the vehicle is being driven or at
a standstill. Some functions are only
available when the vehicle is being
driven.
Info display
The central display in the
Infotainment system displays the time
(and/or outside temperature,
depending on version) and
Infotainment system information.
Press X to switch the Infotainment
system on. Alternatively, it
automatically switches on when the
ignition is switched on.
Depending on system, the
Infotainment system is operated via
buttons and rotary knobs on the
Infotainment system fascia, the
steering column controls, the voice
recognition system (if available) or via
the touchscreen display.
Touchscreen operation
Make the appropriate selection from
the available menus and options by
touching the display screen with the
finger.
For further information, refer to the
Infotainment system instruction.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
104
Instruments and controls
Vehicle messages
Messages appear in the Driver
Information Centre, in combination
with control indicator A or C.
Information messages
Information messages
BATTERY MODE: ECONOMY
ESP OFF
AUTO LIGHTS DEACTIVATED
OIL LEVEL CORRECT
Fault messages
Displayed in combination with control
indicator A. Drive with caution and
seek the assistance of a workshop.
To remove fault message, press
button on end of wiper lever. After a
few seconds the message may
disappear automatically and A
remains illuminated. The fault will
then be stored in the on board
system.
Fault messages
CHECK ESP
CHECK FUEL FILTER
CHECK GEARBOX
CHECK AUTO LIGHTS
Warning messages
These may appear with control
indicator C or in combination with
other warning messages, control
indicators or an audible warning. Stop
engine immediately and seek the
assistance of a workshop.
Warning messages
INJECTION FAULT
ENGINE OVERHEATING
GEARBOX OVERHEATING
Tyre pressure monitoring system
Warning chimes
When starting the engine or whilst
driving
Only one warning chime will sound at
a time.
The warning chime regarding
unfastened seat belts has priority
over any other warning chime.
● If seat belt is not fastened 3 54.
● If a certain speed is exceeded
with the parking brake applied
156.
● If the parking assist detects an
object or a fault is present
164.
● If the vehicle has instruction
transmission automated and the
clutch temperature is too high
151.
● If the vehicle speed briefly
exceeds a set limit 3 90.
● During closing of the power
sliding door 3 28.
● If the sliding door is open and the
parking brake is released 3 28.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Instruments and controls
105
● During activation and
deactivation of alarm monitoring
of vehicle inclination 3 34.
● If the AdBlue level falls below a
certain amount or a fault is
● If the lane departure warning
system detects an unintended
lane change and when the
When the vehicle is parked and/or
the driver's door is opened
● When the key is in the ignition
switch.
● With exterior lights on 3 109.
● There is a fault with the power
● If the vehicle has instruction
the parking brake has not been
applied, neutral is not selected or
the brake pedal has not been
depressed. A corresponding
message may also appear in the
Driver Information Centre 3 103.
● If the sliding side door exterior
handle is in the open position
when unlocking the vehicle 3 28.
● If the parking brake is not applied
when the power sliding door
switch is pressed 3 28.
● If the power sliding door is locked
from the inside with the child lock
● If the engine is in an Autostop but
not switched off. Stop-start
system 3 137.
Trip computer
The trip computer provides
information on driving data, which is
continually recorded and evaluated
electronically.
Depending on vehicle, the following
functions can be selected by pressing
button repeatedly on end of wiper
lever:
● fuel used
● average consumption
● instantaneous consumption
● range
● distance travelled
-------------------------------------------------------------------------------------------------------------------------------------------------------------
106
Instruments and controls
● average speed
● distance before service 3 93
● clock 3 88
● cruise control and speed limiter
● fault and information messages
● odometer 3 91, trip odometer
Fuel used
Displays the amount of fuel
consumed since the last reset.
The measurement can be restarted at
any time by pressing and holding the
button on the end of the wiper lever.
Average consumption
The value is displayed after driving a
distance of 400 metres.
Average consumption is displayed,
taking into consideration the distance
travelled and the fuel used since the
last reset.
The measurement can be restarted at
any time.
Instantaneous consumption
The value is displayed after reaching
a speed of 30 km/h.
Range
The value is displayed after driving a
distance of 400 metres.
The range is calculated from the
current contents of the fuel tank and
the average consumption since the
last reset.
The range will not display if control
indicator Y is illuminated in the
instrument cluster 3 101.
The measurement can be restarted at
any time.
Distance travelled
Displays the distance driven since the
last reset.
The measurement can be restarted at
any time.
Average speed
The value is displayed after driving a
distance of 400 metres.
The average speed since the last
reset is displayed.
The measurement can be restarted at
any time.
Interruptions in the journey with the
ignition off are not included in the
calculations.
Reset trip computer information
To reset the trip computer, select one
of its functions then press and hold
button on end of wiper lever.
The following trip computer
information can be reset:
● fuel used
● average consumption
● distance travelled
● average speed
The trip computer will reset
automatically when the maximum
value of any of the parameters is
exceeded.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Instruments and controls
107
Fuel economy rating (ecoScoring)
If equipped, a rating of 0 to 100 is
shown in the Infotainment system
display screen, to help evaluate fuel
efficiency, based on your driving
style.
Higher ratings indicate better fuel
economy.
Tips to improve fuel economy are also
given in the display. Journeys can be
saved in the system memory,
enabling you to compare
performances. Refer to Infotainment
instruction for further information.
Vehicle messages 3 104.
Journey record
When the engine is switched off, a
record of the last journey may be
shown in the Infotainment system
display screen.
The following information is
displayed:
● average fuel consumption
● trip odometer
● fuel saved in km
Refer to Infotainment instruction for
further information.
Interruption of power supply
If the power supply has been
interrupted or if the vehicle battery
voltage has dropped too low, the
values stored in the trip computer will
be lost.
Tachograph
The tachograph is operated as
described in the operating
instructions supplied. Observe
regulations regarding use.
Control indicator & illuminates in the
instrument cluster in the event of a
fault. Seek the assistance of a
workshop.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
108
Instruments and controls
Note
When a tachograph is fitted, the total
distance travelled may be shown
only on the tachograph and not in the
odometer within the instrument
display.
Odometer 3 91.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Lighting
109
Lighting
Exterior lighting . . . . . . .. 109
Light switch . . . . . . . .. 109
Automatic light control . . . . 109
High beam . . . . . . . ... 110
High beam assist . . . . . . 110
Headlight flash . . . . . . . 111
Headlight range adjustment . 111
Headlights when driving
abroad . . . . . . . . . 111
Daytime running lights . . . . 111
Adaptive forward lighting . . . 112
Hazard warning flashers . . .. 112
Turn and lane-change signals . 112
Front fog lights . . . . . . . 113
Rear fog lights . . . . . . . 113
Reversing lights . . . . . ... 113
Misted light covers . . . . ... 113
Interior lighting . . . . . . ... 114
Interior lights . . . . . . . 114
Load compartment lighting . .. 114
Reading lights . . . . . . .. 115
Lighting features . . . . . . 116
Exit lighting . . . . . . . .. 116
Battery discharge protection . 116
Exterior lighting
Light switch
Turn outer light switch:
7
: off
0
: sidelights
9
P : headlights
AUTO : automatic light control:
headlights are switched on
and off automatically.
Turn inner light switch:
>
: front fog lights
ø
: rear fog lights
High beam control indicator P
Low beam control indicator 9 3 102.
Note
If the headlights have been switched
on instructionly, a warning chime will
sound when the engine is switched
off and when the driver's door is
opened as a reminder that the lights
are still on.
Tail lights
Tail lights are illuminated together
with low beam and sidelights.
Automatic light control
-------------------------------------------------------------------------------------------------------------------------------------------------------------
110
Lighting
When the automatic light control
function is switched on and the
engine is running, the system
switches between daytime running
lights (where fitted) and headlights,
depending on the lighting conditions.
For reasons of safety, the light switch
should always remain in the AUTO
position.
Daytime running lights 3 111.
Automatic headlight activation
During poor lighting conditions the
headlights are switched on.
Additionally, headlights are switched
on if the windscreen wipers have
been activated for several wipes.
High beam
To change between low and high
beam, pull lever until a click is felt.
High beam assist
This feature allows high beam to
function as the main driving light at
night and when vehicle speed is
faster than 45 km/h.
It switches to low beam when:
● The camera in the windscreen
detects the lights of oncoming or
preceding vehicles.
● It is foggy or snowy.
● Driving in urban areas.
If there are no restrictions detected,
the system switches back to high
beam.
Activation
Turn the outer light switch to AUTO
then pull the turn signal lever to
activate high beam assist.
The control indicator í illuminates
continuously in the instrument cluster
when the assist is activated, while the
blue control indicator 7 3 102
illuminates when high beam is on.
Control indicator í 3 102.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Lighting
111
Note
Use of the system does not relieve
the driver from full responsibility for
vehicle operation.
Deactivation
Pull the turn signal lever again.
Control indicator í extinguishes.
High beam assist is also deactivated
when the outer light switch is moved
out of the AUTO position.
Note
Depending on version, the system
can be also be deactivated via the
Infotainment system. Refer to
Infotainment instruction for further
information.
General information
Performance of the system can be
affected due to the following:
● Extreme weather conditions, e.g.
heavy rain, fog or snow.
● The front camera or the
windscreen is obstructed, e.g. by
a portable navigation system.
● Oncoming or preceding vehicle
lights are not detected.
● Headlights are not adjusted
correctly.
● Various reflective surfaces may
also cause the system to fail to
detect other vehicles.
Headlight flash
To activate the headlight flash, pull
lever.
Headlight range adjustment
Instruction headlight range
adjustment
With low beam switched on, adapt the
headlight range to suit the vehicle
load to prevent dazzling of oncoming
traffic.
Turn knurled wheel to required
position:
0 : front seat occupied
4 : loaded up to permissible
maximum weight
Headlights when driving
abroad
The asymmetrical headlight beam
extends visibility at the edge of the
road at the passenger side.
However, when driving in countries
where traffic drives on the opposite
side of the road, adjust the headlights
to prevent dazzling of oncoming
traffic.
Have the headlights adjusted by a
workshop.
Daytime running lights
Daytime running lights increase
visibility of the vehicle during daylight.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
112
Lighting
The lights operate automatically
when the ignition is switched on.
If the vehicle is equipped with the
automatic light control function, the
system switches between daytime
running lights and headlights
automatically depending on the
lighting conditions. Automatic light
Adaptive forward lighting
Cornering light
Depending on the steering angle,
vehicle speed and gear selected
when cornering, an additional light
will illuminate the corner of the road
on the respective side when the
headlights are switched on.
The cornering light is switched off
automatically after prolonged use and
at vehicle speeds above 40 km/h.
Hazard warning flashers
Operated by pressing ¨.
In the event of hard braking, the
hazard warning flashers may turn on
automatically. Switch off by pressing
¨
.
Turn and lane-change
signals
lever up
: right turn signal
lever down : left turn signal
A resistance point can be felt when
moving the lever.
Constant flashing is activated when
the lever is moved beyond the
resistance point. It is deactivated
when the steering wheel is moved in
the opposite direction or lever is
instructionly moved back to its neutral
position.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Lighting
113
Activate temporary flashing by
holding the lever just before the
resistance point. Turn signal lights will
flash until lever is released.
To activate three flashes, tap the
lever briefly without passing the
resistance point.
Front fog lights
Turn inner switch to position > and
release.
Front fog lights operate with engine
running and headlights switched on.
Rear fog lights
Turn inner switch to position ø and
release.
Rear fog lights operate with engine
running and headlights switched on.
Reversing lights
The reversing lights come on when
the ignition is on and reverse gear is
selected.
Misted light covers
The inside of the light covers may mist
up briefly in poor, wet and cold
weather conditions, in heavy rain or
after washing. The mist disappears
quickly by itself; to help, switch on the
headlights.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
114
Lighting
Interior lighting
Interior lights
Courtesy lights illuminate when the
vehicle is unlocked with the remote
control or the front doors are opened.
When the doors are closed, the
courtesy light extinguishes after a
delay or immediately after the ignition
is switched on.
Front courtesy light
With the switch in its central position,
the light functions as a courtesy light.
Operated by pressing the switch c:
● on constantly
● on when the doors are unlocked
and opened
● off constantly
Rear courtesy lights
Combi, Bus
Low level and overhead courtesy
lights are located in the rear
passenger compartment.
Operate rocker switch on the
instrument panel:
press OFF : off
press c : on
Reading lights l 3 115.
Load compartment lighting
Load compartment lighting can be set
to illuminate when the side and rear
doors are opened, or switched on
constantly.
With the switch in its central position,
the light functions as a courtesy light.
Operated by pressing the switch c:
● on constantly
● on when the doors are unlocked
and opened
● off constantly
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Lighting
115
When the doors are closed, the
courtesy light extinguishes after a
delay or immediately after the ignition
is switched on.
Reading lights
Front reading light
Operated with l.
The reading light can be directed as
required, depending on version.
Rear reading lights
Combi, Bus
Operate rocker switch on the
instrument panel:
press l
: on
press OFF : off
Courtesy lights c 3 114.
Each reading light can then be
switched on or off individually and
directed as required.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
116
Lighting
Lighting features
Exit lighting
Headlights come on for approx.
30 seconds after the vehicle is parked
and the system is activated.
Activating
1. Switch off ignition.
2. Remove ignition key.
3. Pull turn signal lever towards
steering wheel.
This action can be repeated up to
four times.
The headlights are turned off
immediately by turning the light switch
to any position and returning to 7.
Battery discharge protection
To prevent discharge of the vehicle
battery when the ignition is switched
off, some interior lights may be
switched off automatically after some
time.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Climate control
117
Climate control
Climate control systems . . . . 117
Heating and ventilation system 117
Air conditioning system . . ... 118
Electronic climate control
system . . . . . . . . . 119
Rear heating system . . . ... 121
Rear air conditioning system ... 123
Auxiliary heater . . . . . . 124
Air vents . . . . . . . . . . 130
Adjustable air vents . . . . . 130
Fixed air vents . . . . . . . 131
Glovebox cooler . . . . . .. 131
Maintenance . . . . . . . .. 131
Air intake . . . . . . . . . 131
Pollen filter . . . . . . . ... 131
Air conditioning regular
operation . . . . . . . . 131
Service . . . . . . . . . 131
Climate control systems
Heating and ventilation
system
Controls for:
● temperature
● fan speed
● air distribution
● demisting and defrosting
Heated rear window Ü 3 41, Heated
seats ß 3 50.
Temperature
red : warm
blue : cold
Heating will not be fully effective until
the engine has reached normal
operating temperature.
Fan speed
Adjust the air flow by switching the fan
to the desired speed.
Air distribution
M
: to head area
L
: to head area and foot well
K
: to foot well
J
: to windscreen, front door
windows and foot well
V
: to windscreen and front door
windows
Intermediate settings are possible.
Demisting and defrosting the
windows
● Set temperature control to
warmest level.
● Set fan speed to highest level.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
118
Climate control
● Set air distribution control to V.
● Switch on heated rear window Ü.
● Open side air vents as required
and direct them towards door
windows.
● For simultaneous warming of the
foot well, set air distribution
control to J.
Air conditioning system
Additional to the heating and
ventilation system, the air
conditioning system has controls for:
A/C : cooling
u
: air recirculation
Heated rear window Ü 3 41, Heated
seats ß 3 50.
Cooling (A/C)
Press A/C to switch on cooling. The
LED in the button illuminates to
indicate activation. Cooling is only
functional when the engine is running
and climate control fan is switched on.
Press A/C again to switch off cooling.
The air conditioning system cools and
dehumidifies (dries) the air when
outside temperature is a little above
the freezing point. Therefore
condensation may form and drip from
under the vehicle.
If no cooling or drying is required,
switch the cooling system off to save
fuel.
Note
If the climate control is set to
maximum cooling while the ambient
temperature is high, an Autostop
may be inhibited until the required
temperature in the passenger
compartment has been reached.
If the climate control is set to
maximum cooling while the engine is
in an Autostop, the engine may
restart automatically.
Air recirculation system
Press u to activate air recirculation
mode. The LED in the button
illuminates to indicate activation.
Press u again to deactivate air
recirculation mode.
9 Warning
The exchange of fresh air is
reduced in air recirculation mode.
In operation without cooling the air
humidity increases, so the
windows may mist up. The quality
of the passenger compartment air
deteriorates, which may cause the
vehicle occupants to feel drowsy.
Maximum cooling
Briefly open the windows so that hot
air can disperse quickly.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст