Opel Movano (2018 year). Instruction — part 12
Vehicle care
183
Replacing the vehicle battery
Ensure that the battery is always
replaced by the same type of battery.
Seek the assistance of a workshop to
have the vehicle battery replaced.
Stop-start system 3 137.
Charging the vehicle battery
9 Warning
On vehicles with stop-start
system, ensure that the charging
potential does not exceed
14.6 volts when using a battery
charger. Otherwise the vehicle
battery might be damaged.
9 Danger
Ensure adequate ventilation when
charging the battery. There is a
risk of explosion if gases
generated during charging are
allowed to accumulate!
Jump starting 3 213.
Warning label
Meaning of symbols:
● No sparks, naked flames or
smoking.
● Always shield eyes. Explosive
gases can cause blindness or
injury.
● Keep the vehicle battery out of
reach of children.
● The vehicle battery contains
sulfuric acid which could cause
blindness or serious burn
injuries.
● See the Owner's Instruction for
further information.
● Explosive gas may be present in
the vicinity of the battery.
Additional battery
Depending on the vehicle's auxiliary
equipment, certain models may have
an additional battery mounted under
the right-hand front seat.
Note
The additional battery is
automatically connected to the main
vehicle battery only when the engine
is running. It does not need to be
-------------------------------------------------------------------------------------------------------------------------------------------------------------
184
Vehicle care
instructionly disconnected before
disconnecting the main vehicle
battery or before jump starting the
vehicle.
The terminals are designed for
additional electrical consumers up to
a maximum of 50 A.
Jump starting 3 213.
Diesel fuel filter
Drain diesel fuel filter of residual
water at every engine oil change.
Place a container underneath the
filter housing. Loosen the knurled
screws on the filter cover and on the
lower part of the filter by approx. one
turn, to drain off the water.
The filter is drained as soon as diesel
fuel emerges from the knurled screw
at the bottom. Retighten the two
screws.
Check diesel fuel filter at shorter
intervals if the vehicle is subjected to
extreme operating conditions.
Diesel fuel system bleeding
If the fuel tank has been run dry, it will
be necessary to air vent or bleed the
diesel fuel system.
Fill the tank with fuel and proceed as
follows:
1. Place a suitable container
underneath the fuel filter vent
screw to collect fuel.
2. Loosen the vent screw (arrowed)
by one turn.
3. Instructionly operate the in-line
supply pump slowly and steadily
until fuel discharging from the
loosened vent screw is free of air
bubbles.
4. Retighten the vent screw.
In vehicles without an in-line supply
pump, fill the tank with fuel and
proceed as follows:
Caution
Do not turn ignition key to position
3 before beginning the bleeding
procedure.
Ignition switch positions 3 135.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Vehicle care
185
1. Turn ignition key to position 2 and
hold for five seconds.
2. Turn key back to position 1 and
wait for three seconds.
3. Repeat Step 1 and 2 multiple
times.
4. Turn key to position 3, then return
to 0.
If the engine cannot be started after
several attempts to bleed the diesel
fuel system, seek the assistance of a
workshop.
Wiper blade replacement
Wiper blades on the windscreen
If required, use the step located below
the headlights to reach the
windscreen wiper.
Lift wiper arm, press retaining clip
towards wiper arm and detach wiper
blade.
Attach the wiper blade slightly angled
to the wiper arm and push until it
engages.
Lower wiper arm carefully.
Bulb replacement
Ensure the ignition is switched off
completely (the vehicle must not be in
an Autostop 3 137) and turn off the
relevant switch or close the doors.
Only hold a new bulb at the base. Do
not touch the bulb glass with bare
hands.
Use only the same bulb type for
replacement.
Bulb check
After a bulb replacement, switch on
the ignition, operate and check the
lights.
Performing work 3 177.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
186
Vehicle care
Headlights
Headlights have separate systems for
high beam 1 and low beam 2.
High beam
1. Remove headlamp protective
cover.
2. Detach wiring connector from
bulb holder.
3. Release spring clip and withdraw
bulb holder from reflector
housing.
4. Detach bulb from bulb holder and
renew the bulb.
5. Insert bulb holder in reflector
housing.
6. Secure with spring clip and attach
wiring connector to bulb holder.
7. Install headlamp protective cover.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Vehicle care
187
Low beam
1. Remove headlamp protective
cover.
2. Detach wiring connector from
bulb holder.
3. Rotate bulb holder anti-clockwise
to disengage.
4. Withdraw bulb holder from
reflector housing.
5. Detach bulb from bulb holder and
renew the bulb.
6. Insert the bulb holder, engaging
the two lugs in the reflector
housing and rotate clockwise to
secure.
7. Attach wiring connector to bulb
holder.
8. Install headlamp protective cover.
Sidelights
1. Remove protective cover.
2. Detach wiring connector from
bulb holder.
3. Rotate bulb holder anti-clockwise
to disengage.
4. Withdraw bulb holder from
reflector housing.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
188
Vehicle care
5. Detach bulb from bulb holder and
renew the bulb.
6. Insert the bulb holder, engaging
the two lugs in the reflector
housing and rotate clockwise to
secure.
7. Attach wiring connector to bulb
holder.
8. Install protective cover.
Adaptive forward lighting
Cornering light
Headlights have separate systems for
high beam 1 and low beam 2. The
cornering light 3 is located between
the headlights.
1. Remove protective cover.
2. Detach wiring connector from
bulb holder.
3. Rotate bulb holder anti-clockwise
to disengage.
4. Withdraw bulb holder from
reflector housing.
5. Detach bulb from bulb holder and
renew the bulb.
6. Insert the bulb holder, engaging
the two lugs in the reflector
housing and rotate clockwise to
secure.
7. Attach wiring connector to bulb
holder.
8. Install protective cover.
Fog lights
Have the front fog light bulbs replaced
by a workshop.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Vehicle care
189
Front turn signal lights
1. Remove protective cover.
2. Detach wiring connector from
bulb holder.
3. Rotate bulb holder anti-clockwise
to disengage.
4. Withdraw bulb holder from
reflector housing.
5. Detach bulb from bulb holder and
renew the bulb.
6. Insert the bulb holder, engaging
the two lugs in the reflector
housing and rotate clockwise to
secure.
7. Attach wiring connector to bulb
holder.
8. Install protective cover.
Tail lights
Rear brake, tail, turn signal,
reverse and fog tail lights
1. Remove the upper and lower trim
panels from the rear pillar.
2. Unscrew the two nuts from the
locating pins on the rear of the
lamp assembly.
3. Withdraw the lamp assembly
rearwards from the outer side.
4. Detach wiring connector from
lamp assembly.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
190
Vehicle care
5. Remove the three screws from
the rear of the lamp assembly.
6. Remove bulb holder from the
lamp assembly.
7. Push bulb into socket slightly,
rotate anti-clockwise, remove and
renew bulb.
Turn signal light (1)
Tail and brake light (2)
Reverse light (3)
Rear fog light, may be on one side
only (4)
8. Replace bulb holder in lamp
assembly.
9. Replace the three screws on the
rear of the lamp assembly.
10. Reattach wiring connector to lamp
assembly.
11. Replace lamp assembly from the
outer side into original position,
ensuring that it is seated correctly.
12. Replace the two nuts onto the
locating pins on the rear of the
lamp assembly.
13. Install the upper and lower trim
panels to the rear pillar.
Crew Cab, Chassis Cab
Rear brake, tail, turn signal, reverse
and fog tail lights
1. Remove the four screws from the
lens.
2. Remove lens from the aperture.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Vehicle care
191
3. Push bulb into socket slightly,
rotate anti-clockwise, remove and
renew bulb.
Turn signal light (1)
Tail and brake light (2)
Reverse light (3)
Rear fog light, may be on one side
only (4)
4. Install lens in aperture and
replace the four screws.
Side turn signal lights
1. Push the lamp assembly to the
right and pull at the left-hand side
of the lamp assembly to release
from the aperture.
2. Detach wiring connector from
lamp assembly.
3. Remove bulb holder from lamp
assembly by rotating 90° and
renew bulb.
4. Install bulb holder in lamp
assembly.
5. Attach wiring connector to lamp
assembly.
6. Insert lamp assembly into
aperture and push to the left to
secure.
Mirror turn signal lights
1. Move the lower mirror assembly
from the front to access the screw.
2. Remove the screw using a torx
screwdriver.
3. Remove bulb holder from the rear
of the lower mirror assembly.
4. Renew bulb.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
192
Vehicle care
5. Install bulb holder in lower mirror
assembly.
6. Replace the screw.
Centre high-mounted brake
light
1. Remove cover from the inside of
the rear door.
2. Unscrew the nut from the locating
pin at the rear of the lamp
assembly.
3. Remove the lamp assembly from
the aperture on the outer side.
4. Detach wiring connector from
lamp assembly.
5. Remove bulb holder from lamp
assembly and renew bulb.
6. Install bulb holder in lamp
assembly and reattach wiring
connector to lamp assembly.
7. Replace lamp assembly into
aperture, ensuring that it is seated
correctly.
8. Replace the nut onto the locating
pin on the rear of the lamp
assembly.
9. Install cover on the inside of the
rear door.
Number plate light
1. Unclip lamp assembly using a flat
blade screwdriver.
2. Detach wiring connector from
lamp assembly.
3. Remove lens cover and renew
bulb.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Vehicle care
193
4. Install lens cover and attach
wiring connector to lamp
assembly.
5. Install lamp assembly.
Crew Cab, Chassis Cab
1. Remove the two screws from the
lens cover.
2. Remove lens cover and renew
bulb.
3. Install the lens cover and replace
the two screws.
Interior lights
Front courtesy light
1. Remove lamp assembly using a
flat blade screwdriver.
2. Renew bulb.
3. Install lamp assembly.
Load compartment light
1. Remove lamp assembly using a
flat blade screwdriver.
2. Detach wiring connector from
lamp assembly.
3. Remove lens cover and renew
bulb.
4. Install lens cover and attach
wiring connector to lamp
assembly.
5. Install lamp assembly.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
194
Vehicle care
Front door panel light
1. Remove lamp assembly using a
flat blade screwdriver.
2. Rotate bulb holder anti-clockwise
to disengage.
3. Renew bulb and insert the bulb
holder.
4. Install lamp assembly.
Rear courtesy lights
Have bulbs replaced by a workshop.
Glovebox light
Have bulbs replaced by a workshop.
Instrument panel
illumination
Have bulbs replaced by a workshop.
Electrical system
Fuses
Data on the replacement fuse must
match the data on the defective fuse.
There are two fuse boxes in the
vehicle:
● on the left-hand side of the
instrument panel, behind the trim
panel
● in the engine compartment
located below the coolant
expansion tank
Combi
An additional fuse box is located
behind a trim panel on the right-hand
side of the load compartment, beside
the rear door.
Bus
An additional fuse box is located on
the lower right-hand side of the load
compartment, below the step trim
panel.
Before replacing a fuse, turn off the
respective switch and the ignition.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Vehicle care
195
A blown fuse can be recognised by its
melted wire. Do not replace the fuse
until the cause of the fault has been
remedied.
It is advisable to carry a full set of
fuses. Consult a workshop.
Some functions are protected by
several fuses.
Fuses may also be inserted without
existence of a function.
Note
Not all fuse box descriptions in this
instruction may apply to your vehicle.
When inspecting the fuse box, refer
to the fuse box label.
Fuse extractor
To help in replacing fuses, a fuse
extractor is located in the instrument
panel fuse box.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
196
Vehicle care
Place the fuse extractor on the
various types of fuse from the top or
side, and withdraw fuse.
Engine compartment fuse
box
Located below the coolant expansion
tank.
Some circuits may be protected by
several fuses.
Due to restricted accessibility, have
fuses replaced by a workshop.
Symbol Circuit
S
Right side lights
T
Left side lights
W
Right low beam
a
Left low beam
>
Front fog light
L
Left high beam
N
Right high beam
u
ABS
K
Windscreen wiper
Symbol Circuit
n
Heating and ventilation
system / Air conditioning
V
Heated windscreen
Q
Pneumatic suspension
Instrument panel fuse box
Located behind the trim panel on the
left-hand side of the instrument panel.
Pull upper part of trim panel to
remove.
Do not store any objects behind this
panel.
Some circuits may be protected by
several fuses.
Symbol Circuit
Z
Infotainment system / Seat
heating / Driver Information
Centre / Audio connec‐
tions / Alarm
?
Power outlet
Ì
Cigarette lighter
e
Instrument panel
U
Central locking
0
Interior lights
O
Turn signals / Rear fog
lights / Body control module
DIAG
Diagnostic connector
u
ABS / Electronic Stability
Program
d
Interior lights / Brake lights
Z
Body control module
STOP Brake light
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Vehicle care
197
Symbol Circuit
I
Body control module /
Power windows / Heating
and ventilation system / Air
conditioning
m
Left heated rear window
n
Right heated rear window
R
Windscreen washer
M
Electronic immobiliser
U
Heated seats
FBL
Cornering light
l
Hands-free connection
&
Tachograph
PTO
Power take-off
j
Horn
Í
Preheating / Diesel fuel filter
x
Climate control fan
d
Heated exterior mirrors
T
Left-hand side light
S
Right-hand side light
Symbol Circuit
O
Navigation system
ADP
Additional adaptations
,
Power windows / Body
control module
Load compartment fuse box
Combi
Located behind the trim panel on the
right-hand side of the load
compartment, beside the rear door.
Using a suitable tool, e.g. a flat-blade
screwdriver, unclip the trim panel at
the three locations shown in the
illustration and remove.
Do not store any objects behind this
panel.
No. Circuit
1
Speed 3: additional evaporator
2
Speed 2: additional evaporator
3
Speed 1: additional evaporator
-------------------------------------------------------------------------------------------------------------------------------------------------------------
198
Vehicle care
Bus
Located below the step trim panel on
the lower right-hand side of the load
compartment.
Using a suitable tool, e.g. a flat-blade
screwdriver, unclip the trim panel at
the three locations shown in the
illustration and remove.
Do not store any objects behind this
panel.
No. Circuit
1
Stop-start
2
Power sliding door lock electro‐
magnet
3
Power sliding door lock buzzer
4
Speed 2: right-hand evaporator
fan
5
Speed 2: left-hand evaporator
fan
6
Speed 1: left-hand evaporator
fan
7
Left-hand heating
8
Speed 3: left-hand evaporator
fan
9
Condenser fan
10 Right-hand heating
11 Speed 3: right-hand evaporator
fan
12 Power sliding door
13 Corridor lighting
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст