Opel Frontera UBS. Service manual — part 1445
7A–22
AUTOMATIC TRANSMISSION (AW30-40LE)
TCC DATA
Item
Unit
Enigne running at idle
Current Gear
1
Lock Up
Inactive, Active
Inactive
AT Output Speed (Automatic Transmission)
RPM
0 RPM
Output Speed (Meter Signal Side)
RPM
0 RPM
AT Input Speed (Automatic Transmission)
RPM
0 RPM
Engine Speed
RPM
695
~
745 RPM
Vehicle Speed (Output Side)
km/h
0 km/h
Throttle Position
%
0 %
Gear Ratio
:1
2.804
AT Oil Temperature (Automatic Transmission)
°
C,
°
F
70
~
80
°
C (158
∼
176
°
F)
TCC Slip Speed
RPM
695
~
745 RPM
TCC Solenoid Pressure Desired
kPa
0 kPa
Desired TCC Solenoid Current
mA
0 mA
Actual TCC Solenoid Current
mA
0 mA
AUTOMATIC TRANSMISSION (AW30-40LE)
7A–23
INTERMITTENT CONDITIONS
If the Tech2 displays a code as intermittent, or if after a
test drive a code does not reappear, the problem is most
likely a faulty electrical connection or loose wiring.
Terminals should always be the prime suspect.
Intermittent rarely occur in sophisticated electronic
components such as the Transmission Control Module
(TCM).
When an intermittent problem is encountered, check
suspect circuits for:
• Poor terminal to wire connection.
• Terminals not fully seated in the connector body
(backed out).
• Improperly formed or damaged terminals.
• Loose, dirty, or corroded ground connections.
HINT: Any time you have an intermittent in more than
one circuit, check whether the circuits share a
common ground connection.
• Pinched or damaged wires.
• Electro-Magnetic Interference (EMI)
HINT: Check that all wires are properly routed away
from spark plug wires, distributor wires, coil,
and generator. Also check for improperly
installed electrical options, such as lights, 2-
way radios, etc.
Use the F2: SNAPSHOT mode of the Tech2 to help
isolate the cause of an intermittent fault. The snapshot
mode will record information before and after the
problem occurs. Set the snapshot to "trigger" on the
suspect code (or codes) or, if you notice the reported
symptom during test drive, trigger the snapshot
manually.
After the snapshot has been triggered, command the
Tech2 to play back the flow of data recorded from each
of the various sensors. Signs of an intermittent fault in a
sensor circuit are a sudden unexplainable jump in data
values out of the normal range.
7A–24
AUTOMATIC TRANSMISSION (AW30-40LE)
826RY00004
IDENTIFICATION OF TRANSMISSION
CONTROL MODULE (TCM)
ISUZU Part No: 8-97230-821-0
AUTOMATIC TRANSMISSION (AW30-40LE)
7A–25
DIAGNOSTIC TROUBLE CODES (DTC) CHECK
DTC
NUMBER
FLASHING
CODE
DESCRIPTION
P0120
21
ANALOG THROTTLE SIGNAL FAILURE (VTH)
P0502
24
SPEED METER SENSOR FAILURE (SP1)
P0705
17
GEAR SELECTOR FAILURE (PRND2L)
P0710
16
OIL TEMPERATURE SENSOR FAILURE (OT2)
P0717
14
INPUT REVOLUTION SENSOR FAILURE (NC0)
P0722
11
OUTPUT REVOLUTION SENSOR FAILURE (SP2)
P0727
13
ENGINE REVOLUTION SIGNAL FAILURE (NE)
P0743
33
TORQUE CONVERTER CLUTCH CONTROL LOCK-UP (ON/OFF) SOLENOID
FAILURE (SL)
P0748
35
PRESSURE CONTROL SOLENOID FAILURE (STH)
P0753
31
SOLENOID 1 FAILURE (S1)
P0758
32
SOLENOID 2 FAILURE (S2)
P1121
23
ANALOG THROTTLE SIGNAL FAILURE (VREF, VGND)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст