Opel Frontera UBS. Service manual — part 409
ENGINE COOLING 6B – 5
ON-VEHICLE SERVICE
WATER PUMP
REMOVAL
Preparation
•
Drain coolant.
1. P/S pump Drive Belts
•
Loosen P/S pump mounting bolt, loosen adjust
bolts and remove the drive belts.
2. AC Generator Drive Belt
•
Loosen AC Generator mounting bolt (bottom
side), adjust plate lock bolt, and remove the drive
belt.
3. Cooling Fan Assembly
•
Remove lock nut and take out cooling fan
assembly, distance piece, and fan pulley.
4. Crankshaft Damper Pulley.
5. Gear Case Cover.
6. Water Pump Assembly
7. O-ring
INSPECTION
Make necessary repair and parts replacement if extreme
wear or damage is found during inspection. Should any
of the following problems occur, the entire water pump
assembly must be replaced.
•
Cracks in the coolant pump body
•
Coolant leakage from the seal unit
•
Play or abnormal noise in the bearing
•
Cracks or corrosion in the impeller
6B – 6 ENGINE COOLING
INSTALLATION
7. O-ring
•
Set O-ring in water pump body groove.
6. Water Pump Assembly
•
Install water pump assembly, and tighten to
specified torque.
20(2.0/14)
N·m (Kg·m/lb.ft)
5. Gear Case Cover
•
Install gear case cover, and tighten to specified
torque.
8(0.8/69)
N·m (Kg·m/lb·in)
4. Crankshaft Damper Pulley
•
Install crankshaft damper pulley, and tighten to
specified torque.
3. Cooling Fan Assembly
•
Install fan pulley, distance piece, and cooling fan
assembly in this order on water pump, and tighten
to specified torque.
19(1.9/14)
N·m (Kg·m/lb·ft)
2. AC Generator Drive Belt
•
Install AC Generator drive belt and adjust belt
tension.
•
(Refer to Drive Belt Adjustment in this Section).
1. P/S Pump Drive Belts
•
Install P/S pump drive belts and adjust belt
tension.
•
(Refer to Drive Belt Adjustment in this Section).
8(0.8/69)
N·m (Kg·m/lb·in)
ENGINE COOLING 6B – 7
THERMOSTAT
REMOVAL
Preparation
•
Disconnect battery ground cable.
•
Drain coolant from the radiator and engine.
1.
Water Hose; Turbocharger (4JG2-T Only)
2.
Outlet Pipe
•
Remove mounting bolt and remove outlet pipe
together with radiator hose.
3.
Gasket
4.
Thermostat
INSPECTION
Submerge the thermostat assembly in the water.
Place wooden blocks on the bottom of the water
container.
Not to directly heat the thermostat.
Gradually increase the water temperature. Stir the water
so that the entire water is same temperature.
•
Make sure that primary valve begins to open at the
specified temperature.
82 (180 )
°C (°F)
Valve Opening Temperature
6B – 8 ENGINE COOLING
•
Make sure that secondary valve opens fully at the
specified temperature.
Make necessary repair and parts replacement if extreme
wear or damage is found during inspection.
INSTALLATION
4. Thermostat
3. Gasket
2. Outlet Pipe
•
Connect outlet pipe and tighten bolts to the
specified torque.
19(1.9/14)
N·m (Kgm/lb·ft)
1. Water Hose: Turbocharger (4JG2-T Only)
•
Install battery ground cable.
•
Pour coolant,
•
Start the engine and check coolant leakage.
95 (203)
°C (°F)
Valve Full Open Temperature
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст