Opel Frontera UBS. Service manual — part 2380
6G–13
ENGINE LUBRICATION
Oil Filter
Removal
1. Disconnect battery ground cable.
2. Drain engine oil.
3. Remove oil filter using 5-8840-0203-0 filter wrench.
Installation
1. Clean filter fitting surface and apply small amount of
engine oil to sealing surface.
2. Install oil filter cartridge by hand until it comes in
contact with sealing surface then rotate additional 2/3
turn to tighten using 5-8840-0203-0 filter wrench.
050RW001
Legend
(1) Oil Pump
(2) Oil Filter
(3) Oil Gallery
(4) From Filter
(5) To Filter
3. Fill engine oil until full level on dipstick.
4. Reconnect battery ground cable.
6G–14
ENGINE LUBRICATION
Main Data and Specification
General Specification
Item
Specifications
Item
6VE1
Oil capacity
5.3 liters
Torque Specifications
Crankcase, Oil pan, Timing belt tensioner, Timing pulley, timing belt cover, Oil pump, Oil gallery, Oil strainer
N·m (kg·m/Ib ft)
E06R200017
6G–15
ENGINE LUBRICATION
Special Tool
ILLUSTRATION
TOOL NO.
TOOL NAME
5–8840–0203–0
(J–36390)
Wrench; Oil filter
5–8840–2005–0
(J–29107)
Universal pitman arm
puller
5–8840–2153–0
(J–37228)
Seal cutter
5–8840–2287–0
(J–39202)
Installer; Oil pump oil
seal
6H–1
ENGINE SPEED CONTROL SYSTEM (6VE1 3.5L)
ENGINE
ENGINE SPEED CONTROL SYSTEM
CONTENTS
Service Precaution
6H–1
. . . . . . . . . . . . . . . . . . . . . .
Accelerator Pedal
6H–2
. . . . . . . . . . . . . . . . . . . . . . .
Accelerator Pedal and Associated Parts
6H–2
. .
Removal
6H–2
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation
6H–2
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Service Precaution
WARNING: THIS VEHICLE HAS A SUPPLEMENTAL
RESTRAINT SYSTEM (SRS). REFER TO THE SRS
COMPONENT AND WIRING LOCATION VIEW IN
ORDER TO DETERMINE WHETHER YOU ARE
PERFORMING SERVICE ON OR NEAR THE SRS
COMPONENTS OR THE SRS WIRING. WHEN YOU
ARE PERFORMING SERVICE ON OR NEAR THE SRS
COMPONENTS OR THE SRS WIRING, REFER TO
THE SRS SERVICE INFORMATION. FAILURE TO
FOLLOW WARNINGS COULD RESULT IN POSSIBLE
AIR BAG DEPLOYMENT, PERSONAL INJURY, OR
OTHERWISE UNNEEDED SRS SYSTEM REPAIRS.
CAUTION: Always use the correct fastener in the
proper location. When you replace a fastener, use
ONLY the exact part number for that application.
ISUZU will call out those fasteners that require a
replacement after removal. ISUZU will also call out
the fasteners that require thread lockers or thread
sealant. UNLESS OTHERWISE SPECIFIED, do not
use supplemental coatings (Paints, greases, or other
corrosion inhibitors) on threaded fasteners or
fastener joint interfaces. Generally, such coatings
adversely affect the fastener torque and the joint
clamping force, and may damage the fastener. When
you install fasteners, use the correct tightening
sequence and specifications. Following these
instructions can help you avoid damage to parts and
systems.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст