Opel Corsa (2019 year). Instruction — part 5
70
Instruments and controls
With ignition off, the power outlet is
deactivated. Additionally, the power
outlet is deactivated in the event of
low vehicle battery voltage.
Electrical accessories that are
connected must comply with the
electromagnetic compatibility
requirements laid down in
DIN VDE 40 839.
Do not connect any current-delivering
accessories, e.g. electrical charging
devices or batteries.
Do not damage the outlet by using
unsuitable plugs.
Stop-start system 3 122.
Cigarette lighter
The cigarette lighter is located in the
centre console.
Press in cigarette lighter. It switches
off automatically once the element is
glowing. Pull out lighter.
Ashtrays
Caution
To be used only for ash and not for
combustible rubbish.
The portable ashtray can be placed in
the cupholders.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Instruments and controls
71
Warning lights, gauges
and indicators
Instrument cluster
The needles of the instruments briefly
rotate to the end position when the
ignition is switched on.
Speedometer
Indicates vehicle speed.
Odometer
The bottom line displays the recorded
distance in km.
Trip odometer
The recorded distance is displayed
since the last reset.
Trip odometer counts up to 9999 km
and then restarts at 0.
Midlevel display
To reset, press SET/CLR on the stalk
for a few seconds 3 83.
Uplevel display
-------------------------------------------------------------------------------------------------------------------------------------------------------------
72
Instruments and controls
Two trip odometer pages are
selectable for different trips.
Select menu ; by pressing Menu
on the stalk. Turn adjuster wheel on
the stalk and select ;1 or ;2.
Each trip odometer page can be reset
separately by pressing SET/CLR on
the stalk for a few seconds on the
respective menu.
Tachometer
Displays the engine speed.
Drive in a low engine speed range for
each gear as much as possible.
Caution
If the needle is in the red warning
zone, the maximum permitted
engine speed is exceeded. Engine
at risk.
Fuel gauge
Displays the fuel level or gas content
in the tank depending on the
operation mode.
Number of LEDs displayed shows the
level in the respective fuel tank. 8
LEDs means fuel tank is full.
During liquid gas operation, the level
in the gas tank is displayed.
Low fuel indication
One remaining LED illuminating white
indicates that the fuel level is low.
If the LED changes to red and Y
illuminates yellow, refuel the tank
soon.
If the LED illuminates red and Y
flashes yellow, refuel immediately.
Never run the fuel tank dry.
The arrow indicates the vehicle side
where the fuel filler flap is located.
Because of the fuel remaining in the
tank, the top-up quantity may be less
than the specified tank capacity.
During liquid gas operation, the
system automatically switches over to
petrol operation when gas tanks are
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Instruments and controls
73
Fuel selector
Pressing LPG switches between
petrol and liquid gas operation as
soon as the required parameters
(coolant temperature, gas
temperature and minimum engine
speed) have been reached. The
requirements are usually fulfilled after
approx. 60 seconds (depending on
exterior temperature) and the first firm
press on the accelerator. The LED
status shows the current operating
mode.
LED off : petrol operation
LED
flashes
: checking conditions for
fuel transition to liquid
gas operation.
Illuminates if conditions
are fulfilled.
LED illu‐
minates
: liquid gas operation
LED
flashes
five
times
and
extin‐
guishes
: liquid gas tank is empty
or failure in liquid gas
system. A message is
displayed in the Driver
Information Centre.
The selected fuel mode is stored and
reactivated at the next ignition cycle,
if conditions allow.
As soon as the liquid gas tank is
empty, petrol operation is
automatically engaged until the
ignition is switched off.
When switching automatically
between petrol or gas operation, a
brief delay of engine tractive power
may be noticeable.
When petrol fuel tank is empty, the
engine will not start.
Every six months, run the petrol tank
down until control indicator Y
illuminates, then refuel. This helps
maintain fuel quality and system
function for petrol operation.
Fill the tank completely at regular
intervals to prevent corrosion in the
tank.
Faults and remedies
If gas mode is not possible, check
whether there is enough liquid gas or
petrol present for starting.
Due to extreme temperatures in
combination with the gas
composition, it may take slightly
longer before the system switches
from petrol to gas mode.
In extreme situations, the system may
also switch back to petrol mode if the
minimum requirements are not
fulfilled. If conditions allow, it might be
possible to instructionly switch back to
liquid gas operation.
Seek the assistance of a workshop in
the event of all other faults.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
74
Instruments and controls
Caution
Repairs and adjustments may only
be made by trained specialists in
order to maintain the safety and
warranty on the LPG system.
Liquid gas is given a particular odour
(odorised) so that any leaks can be
detected easily.
9 Warning
If you smell gas in the vehicle or in
the immediate vicinity, switch to
petrol mode immediately. No
smoking. No naked flames or
ignition sources.
If the gas odour persists, do not start
the engine. Have the cause of the
fault remedied by a workshop.
When using underground car parks,
follow the instructions of the operator
and local laws.
Note
In the event of an accident, switch off
the ignition.
Fuel for liquid gas operation 3 152.
Engine coolant temperature
gauge
Number of LEDs displayed shows the
coolant temperature.
up to 3 LEDs
: engine operating
temperature not
yet reached
4 to 6 LEDs
: normal operating
temperature
more than 6
LEDs
: temperature too
high
Caution
If engine coolant temperature is
too high, stop vehicle, switch off
engine. Danger to engine. Check
coolant level.
Service display
The engine oil life system lets you
know when to change the engine oil
and filter. Based on driving
conditions, the interval at which an
engine oil and filter change will be
indicated can vary considerably.
When the system has calculated that
engine oil life has been diminished, a
warning message appears in the
Driver Information Centre. Have
engine oil and filter changed by a
workshop within one week or
500 km, whichever occurs first.
This can be an additional engine oil
and filter change or part of a regular
service.
To display the remaining engine oil
life duration use the buttons on the
stalk:
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Instruments and controls
75
Press MENU to select the Vehicle
Information Menu ?.
Turn the adjuster wheel to select
Remaining Oil Life.
The remaining engine oil life duration
is displayed in percent in the Driver
Information Centre.
Reset
Press SET/CLR on the stalk for
several seconds to reset. The
remaining engine oil life duration
menu must be active. Switch on
ignition, but not the engine.
The system must be reset every time
the engine oil is changed to ensure
proper functionality. Seek the
assistance of a workshop.
Next service
A message appears in the Driver
Information Centre, when
maintenance of the vehicle is
required. Have maintenance work
carried out by a workshop within one
week or 500 km, whichever occurs
first.
Driver Information Centre 3 83.
Service information 3 202.
Control indicators
The control indicators described are
not present in all vehicles. The
description applies to all instrument
versions.
Depending on the equipment, the
position of the control indicators may
vary. When the ignition is switched
on, most control indicators will
illuminate briefly as a functionality
test.
The control indicator colours mean:
red
: danger, important reminder
yellow : warning, information, fault
green : confirmation of activation
blue
: confirmation of activation
white : confirmation of activation
-------------------------------------------------------------------------------------------------------------------------------------------------------------
76
Instruments and controls
Control indicators in the instrument cluster
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Instruments and controls
77
Control indicators in the centre
console
Overview
O
Turn lights 3 77
X
Seat belt reminder 3 78
v
Airbag and belt tensioners
V
p
Charging system 3 79
Z
Malfunction indicator light
g
R
Brake and clutch system
-
Operate pedal 3 80
u
Antilock brake system (ABS)
R
Gear shifting 3 80
c
)
Lane departure warning 3 80
r
b
Electronic Stability Control and
Traction Control system 3 81
%
w
Tyre pressure monitoring
I
Engine oil pressure 3 81
Y
Low fuel 3 82
d
#
D
Autostop 3 82
8
C
High beam 3 82
>
r
Rear fog light 3 82
m
Cruise control 3 83
A
L
L
h
Turn lights
O
illuminates or flashes green.
Illuminates briefly
The parking lights are switched on.
Flashes
A turn light or the hazard warning
flashers are activated.
Rapid flashing: failure of a turn light or
associated fuse.
Bulb replacement 3 164.
Fuses 3 172.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
78
Instruments and controls
Turn lights 3 104.
Seat belt reminder
Seat belt reminder on front seats
X
for driver's seat illuminates or
flashes red in the tachometer.
k for front passenger seat illuminates
or flashes red in the centre console
when the seat is occupied.
Illuminates
After the ignition has been switched
on, until the seat belt has been
fastened.
Flashes
After having started the engine for a
maximum of 100 seconds, until the
seat belt has been fastened.
Fastening the seat belt 3 40.
Seat belt status on rear seats
X
in the Driver Information Centre
flashes or illuminates.
Illuminates
After having started the engine for a
minimum of 35 seconds, until the seat
belt has been fastened.
Also illuminates if an unfastened seat
belt is fastened whilst driving.
Flashes
After starting-off, when the seat belt is
unfastened.
Fastening the seat belt 3 40.
Airbag and belt tensioners
v
illuminates red.
When the ignition is switched on, the
control indicator illuminates for
approx. 4 seconds. If it does not
illuminate, does not go out after
4 seconds or illuminates whilst
driving, there is a fault in the airbag
system. Seek the assistance of a
workshop. The airbags and belt
pretensioners may fail to trigger in the
event of an accident.
Deployment of the belt pretensioners
or airbags is indicated by continuous
illumination of v.
9 Warning
Have the cause of the fault
remedied immediately by a
workshop.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Instruments and controls
79
Airbag deactivation
V
illuminates yellow.
Illuminates for approx. 60 seconds
after the ignition is switched on. The
front passenger airbag is activated.
* illuminates yellow.
The front passenger airbag is
deactivated 3 47.
9 Danger
Risk of fatal injury for a child using
a child restraint system together
with activated front passenger
airbag.
Risk of fatal injury for an adult
person with deactivated front
passenger airbag.
Charging system
p
illuminates red.
Illuminates when the ignition is
switched on and extinguishes shortly
after the engine starts.
Illuminates when the engine is
running
Stop, switch off engine. Vehicle
battery is not charging. Engine
cooling may be interrupted. The
brake servo unit may cease to be
effective. Seek the assistance of a
workshop.
Malfunction indicator light
Z
illuminates or flashes yellow.
Illuminates when the ignition is
switched on and extinguishes shortly
after the engine starts.
Illuminates when the engine is
running
Fault in the emission control system.
The permitted emission limits may be
exceeded. Seek the assistance of a
workshop immediately.
Flashes when the engine is
running
Fault that could lead to catalytic
converter damage. Ease up on the
accelerator until the flashing stops.
Seek the assistance of a workshop
immediately.
Service vehicle soon
g
illuminates yellow.
Additionally, a warning message is
displayed in the Driver Information
Centre.
The vehicle requires a service.
Seek the assistance of a workshop.
Vehicle messages 3 89.
Brake and clutch system
R
illuminates red.
The brake and clutch fluid level is too
low, when instruction parking brake is
-------------------------------------------------------------------------------------------------------------------------------------------------------------
80
Instruments and controls
9 Warning
Stop. Do not continue your
journey. Consult a workshop.
Illuminates when the instruction parking
brake is applied and ignition is
switched on 3 132.
Operate pedal
-
illuminates or flashes yellow.
Illuminates
Clutch pedal must be depressed to
start the engine in Autostop mode.
Stop-start system 3 122.
Flashes
Clutch pedal must be depressed to
start the engine with the key 3 18,
On some versions, the Driver
Information Centre indicates a
message to operate the clutch pedal
Antilock brake system
(ABS)
u
illuminates yellow.
Illuminates for a few seconds after the
ignition is switched on. The system is
ready for operation when the control
indicator extinguishes.
If the control indicator does not go out
after a few seconds, or if it illuminates
while driving, there is a fault in the
ABS. The brake system remains
operational but without ABS
regulation.
Antilock brake system 3 131.
Gear shifting
R
with the number of a higher gear is
indicated, when upshifting is
recommended for fuel saving
reasons.
Power steering
c
illuminates yellow.
Illuminates with power steering
disabled
Failure in the power steering system.
Consult a workshop.
Illumination of c and b
simultaneously
Power steering system must be
calibrated, system calibration 3 134.
Lane departure warning
)
illuminates green or flashes yellow.
Illuminates green
System is switched on and ready to
operate.
Flashes yellow
System recognises an unintended
lane change.
Lane departure warning 3 149.
Parking assist
r illuminates yellow.
Fault in system
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Instruments and controls
81
or
Fault due to sensors that are dirty or
covered by ice or snow
or
Interference due to external sources
of ultrasound. Once the source of
interference is removed, the system
will operate normally.
Have the cause of the fault in the
system remedied by a workshop.
Parking assist 3 141.
Electronic Stability Control
and Traction Control system
b
flashes or illuminates yellow.
Flashes
The system is actively engaged.
Engine output may be reduced and
the vehicle may be braked
automatically to a small degree.
Illuminates
A fault in the system is present. A
warning message or warning code
appears in the Driver Information
Centre. Continued driving is possible.
The system is not operational. Driving
stability, however, may deteriorate
depending on road surface
conditions.
Have the cause of the fault remedied
by a workshop.
Electronic Stability Control 3 133.
Traction Control system 3 133.
Exhaust filter
%
illuminates or flashes yellow.
The exhaust filter requires cleaning.
Continue driving until %
extinguishes. If possible, do not allow
engine speed to drop below
2000 rpm.
Illuminates
The exhaust filter is full. Start cleaning
process as soon as possible.
Flashes
The maximum filling level of the filter
is reached. Start cleaning process
immediately to avoid damage to the
engine.
Exhaust filter 3 125.
Tyre pressure monitoring
system
w illuminates or flashes yellow.
Illuminates
Tyre pressure loss. Stop immediately
and check tyre pressure.
Flashes
Fault in system or tyre without
pressure sensor mounted (e.g. spare
wheel). After 60-90 seconds the
control indicator illuminates
continuously. Consult a workshop.
Tyre pressure monitoring system
Engine oil pressure
I
illuminates red.
Illuminates when the ignition is
switched on and extinguishes shortly
after the engine starts.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
82
Instruments and controls
Illuminates when the engine is
running
Caution
Engine lubrication may be
interrupted. This may result in
damage to the engine and/or
locking of the drive wheels.
1. Depress the clutch.
2. Set selector lever to neutral.
3. Move out of the flow of traffic as
quickly as possible without
impeding other vehicles.
4. Switch off the ignition.
9 Warning
When the engine is off,
considerably more force is needed
to brake and steer.
During an Autostop, the brake
servo unit will still be operational.
Do not remove key until vehicle is
stationary, otherwise the steering
wheel lock could engage
unexpectedly.
Keep engine turned off and let the
vehicle be towed to a workshop.
Low fuel
Y
illuminates or flashes yellow.
Illuminates
Level in fuel tank is too low.
Flashes
Fuel used up. Refuel immediately.
Never run the fuel tank dry.
Refuelling 3 152.
Catalytic converter 3 126.
Immobiliser
d
flashes yellow.
Fault in the immobiliser system. The
engine cannot be started.
Immobiliser 3 28.
Reduced engine power
#
illuminates yellow.
The engine power is limited. Consult
a workshop.
Autostop
Autostop active
D
illuminates red or white.
Engine is in an Autostop.
Stop-start system 3 122.
Exterior light
8
illuminates green.
The exterior lights are on 3 100.
High beam
C illuminates blue.
Illuminated when high beam is on or
during headlight flash 3 102.
Front fog lights
>
illuminates green.
The front fog lights are on 3 104.
Rear fog light
r
illuminates yellow.
The rear fog light is on 3 105.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Instruments and controls
83
Cruise control
m
illuminates white or green.
Illuminates white
The system is on.
Illuminates green
Cruise control is active.
Cruise control 3 135.
Vehicle detected ahead
A
illuminates green.
A vehicle ahead is detected in the
same lane.
Forward collision alert 3 138.
Speed limiter
L
illuminates in the Driver
Information Centre when Speed
limiter is active. Set speed is indicated
alongside L symbol.
Speed limiter 3 137.
Traffic sign assistant
L
displays detected traffic signs as a
control indicator.
Traffic sign assistant 3 146.
Door open
h
illuminates.
A door or the tailgate is open.
Displays
Driver Information Centre
The Driver Information Centre is
located in the instrument cluster.
Depending on the version and
equipment, the Driver Information
Centre is available as Midlevel
display or Uplevel display.
Driver Information Centre indicates
depending on the equipment:
● vehicle information and settings
● trip/fuel information
● economic information
The following indications appear if
required:
● warning messages 3 89
● gear shift indication 3 80
● drive mode indication 3 127
● tyre pressure warning 3 180
● seat belt reminder indication
● Autostop indication 3 122
● service information 3 79
-------------------------------------------------------------------------------------------------------------------------------------------------------------
84
Instruments and controls
Selecting menus and functions
The menus and functions can be
selected via the buttons on the stalk.
Press MENU to switch between the
main menus or to return from a
submenu to the next higher menu
level.
Turn the adjuster wheel to select a
submenu of the main menu or to set
a numeric value.
Press SET/CLR to select and confirm
a function.
Vehicle and service messages are
popped-up in the Driver Information
Centre if required. Confirm messages
by pressing SET/CLR.
Vehicle messages 3 89.
Midlevel display
Main menus are:
● trip/fuel information, see
description below
● vehicle information, see
description below
Some of the displayed functions differ
when the vehicle is being driven or at
a standstill. Some functions are only
available when the vehicle is being
driven.
Uplevel display
Main menus are:
● trip/fuel information menu,
displayed by ;, see
description below
● vehicle information menu,
displayed by ?, see
description below
● eco information menu, displayed
by @, see description below
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Instruments and controls
85
Note
Some systems override the main
menu tabs. The currently active tab
is indicated by a small arrow head.
Some of the displayed functions differ
when the vehicle is being driven or at
a standstill. Some functions are only
available when the vehicle is being
driven.
Trip/Fuel information menu;
Possible pages are:
● digital vehicle speed
● trip odometer
● average fuel economy
● average vehicle speed
● instantaneous fuel economy
● fuel range
● fuel range LPG version
● timer
● outside temperature
Selection and indication is different
between Midlevel display and Uplevel
display.
Digital vehicle speed
Digital display of the instantaneous
speed.
Trip odometer
Trip odometer displays the current
distance since a certain reset.
Trip odometer counts up to
9999.9 km and then restarts at 0.
Turn the adjuster wheel to select
between trip odometer 1 and 2 for
Uplevel display.
To reset, press SET/CLR for a few
seconds while viewing this page.
The information of trip page 1 and 2
can be reset separately while the
respective display is active.
Average fuel economy
Display of average consumption. The
measurement can be reset at any
time and starts with a default value.
To reset, press SET/CLR for a few
seconds while viewing this page.
The information of trip page 1 and 2
can be reset separately while the
respective display is active.
On vehicles with LPG engines:
Average consumption is indicated for
the currently selected mode, LPG or
petrol.
Average vehicle speed
Display of average speed. The
measurement can be reset at any
time.
To reset, press SET/CLR for a few
seconds while viewing this page.
The information of trip page 1 and 2
can be reset separately while the
respective display is active.
Instantaneous fuel economy
Display of the instantaneous
consumption.
On vehicles with LPG engines:
Instantaneous consumption is
indicated for the currently selected
mode, LPG or petrol.
Fuel range
Range is calculated from current fuel
tank level and current consumption.
The display shows average values.
After refuelling, the range is updated
automatically after a brief delay.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст