Opel Tigra (2009 year). Instruction — part 7
98
Messages are indicated mainly in the
Driver Information Center (DIC), in
some cases together with a warning
and signal buzzer.
Press the SET/CLR button, the
MENU button or turn the adjuster
wheel to confirm a message.
Vehicle messages on the
Midlevel-Display
The vehicle messages are displayed
as code numbers.
No. Vehicle message
2
No radio remote control
detected, depress clutch pedal
for a restart
3
Engine coolant level low
4
Air conditioning off
5
Steering wheel is locked
No. Vehicle message
6
Depress brake pedal to release
electrical parking brake
7
Turn steering wheel, switch
ignition off and then on
9
Turn steering wheel, start
engine again
12 Vehicle overloaded
13 Compressor overheated
15 Centre high-mounted brake
light failure
16 Brake light failure
17 Headlight levelling malfunction
18 Left low beam failure
19 Rear fog light failure
20 Right low beam failure
21 Left sidelight failure
22 Right sidelight failure
23 Reversing light failure
-------------------------------------------------------------------------------------------------------------------------------------------------------------
99
No. Vehicle message
24 Number plate light failure
25 Left front turn signal failure
26 Left rear turn signal failure
27 Right front turn signal failure
28 Right rear turn signal failure
29 Check trailer brake light
30 Check trailer reversing light
31 Check left trailer turn signal
32 Check right trailer turn signal
33 Check trailer rear fog light
34 Check trailer rear light
35 Replace battery in radio remote
control
48 Clean side blind zone alert
system
50 Activated pedestrian protection
system, reset bonnet
53 Tighten gas cap
No. Vehicle message
54 Water in diesel fuel filter
55 Diesel particle filter is full
59 Open and then close driver
window
60 Open and then close front
passenger window
61 Open and then close rear left
window
62 Open and then close rear right
window
65 Theft attempted
66 Service theft alarm system
67 Service steering wheel lock
68 Service power steering
69 Service suspension system
70 Service level control system
71 Service rear axle
No. Vehicle message
74 Service AFL
75 Service air conditioning
76 Service side blind zone alert
system
78 Service pedestrian protection
system
79 Top up engine oil
81 Service transmission
82 Change engine oil soon
83 Service adaptive cruise control
84 Engine power is reduced
94 Shift to park before exiting
95 Service airbag
128 Bonnet open
174 Low battery
-------------------------------------------------------------------------------------------------------------------------------------------------------------
100
Vehicle messages on the
Uplevel-Display
The vehicle messages are displayed
as text. Follow the instructions given
in the messages.
The system displays messages
regarding the following topics:
■ Fluid levels
■ Anti-theft alarm system
■ Brakes
■ Drive systems
■ Ride control systems
■ Cruise control
■ Object detection systems
■ Lighting, bulb replacement
■ Wiper/washer system
■ Doors, windows
■ Radio remote control
■ Seat belts
■ Airbag systems
■ Engine and transmission
■ Tyre pressure
■ Diesel particle filter
Vehicle messages on the
Colour-Info-Display
Some important messages appear
additionally in the
Colour-Info-Display. Press the
multifunction knob to confirm
a message. Some messages only
pop up for a few seconds.
When starting the engine or
whilst driving
■ If seat belt is not fastened.
■ If a door or the tailgate is not fully
closed when starting off.
■ If a certain speed is exceeded with
parking brake applied.
■ If a programmed speed is
exceeded.
■ If a warning message or a warning
code appears in the Driver
Information Center.
■ If the parking assist detects an
object.
■ If a fault in the automatic locking
system is detected.
■ If the diesel particle filter has
reached the maximum filling level.
When the vehicle is parked and/
or the driver's door is opened
■ When the key is in the ignition
switch.
■ With exterior lights on.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
101
When the battery voltage is running
low, a warning message or warning
code 174 will appear in the Driver
Information Center.
1. Switch off immediately electrical
consumers which are not required
for a safe ride, such as seat
heating, heated rear window or
other main consumers.
2. Charge the battery by driving
continuously for a while or by
using a charging device.
The warning message or warning
code will disappear after the engine
has been started two times running
without voltage drop.
If the battery cannot be recharged,
have the cause of the fault remedied
by a workshop.
The menus and functions can be
selected via the buttons on the turn
signal lever.
Press the MENU button to select the
Trip/Fuel Information Menu.
Turn the adjuster wheel to select one
of the submenus:
■ Trip odometer 1
■ Trip odometer 2
■ Range
■ Average consumption
■ Instantaneous consumption
■ Average speed
■ Digital speed
-------------------------------------------------------------------------------------------------------------------------------------------------------------
102
The information of the two trip
computers can be reset separately,
making it possible to display different
trip distances.
To reset, press the reset knob or
press the SET/CLR button for a few
seconds.
Range
Range is calculated from current fuel
tank content and current
consumption. The display shows
average values.
After refuelling, the range is updated
automatically after a brief delay.
When the fuel level in the tank is low,
a message appears in the Driver
Information Center and in the
Info-Display.
Additionally the control indicator i in
the fuel gauge illuminates.
Average consumption
Display of average consumption. The
measurement can be reset at any
time and starts with a default value.
To reset, press the SET/CLR button
for a few seconds.
Instantaneous consumption
Display of the instantaneous
consumption.
Average speed
Display of average speed. The
measurement can be reset at any
time.
To reset, press the SET/CLR button
for a few seconds.
Digital speed
Digital display of the instantaneous
speed.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
103
The vehicle's behaviour can be
personalised by changing the settings
in the Info-Display.
Some of the personal settings for
different drivers can be memorised
individually for each vehicle key.
Memorised settings 3 21.
Depending on vehicle equipment and
country-specific regulations some of
the functions described below might
not be available.
Some functions are only displayed or
active when the engine is running.
Personal settings in the
Graphic-Info-Display
Press the CONFIG button. The menu
Settings is displayed.
The following settings can be
selected by turning and pressing the
multifunction knob:
■ Languages
■ Time Date
■ Radio settings
■ Phone settings
■ Vehicle settings
In the corresponding submenus the
following settings can be changed:
Languages
Selection of the desired language.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
104
Time Date
Radio settings
See description for Infotainment
system in the Infotainment system
instruction.
Phone settings
See description for Infotainment
system in the Infotainment system
instruction.
Vehicle settings
■ Climate and air quality
Auto fan speed: Modifies the fan
regulation.
Climate control mode: Activate or
deactivate cooling.
Auto rear demist: Automatic
activation of rear heated window.
■ Comfort settings
Chime volume: Change the volume
of warning chimes.
Personalization by driver: Activate
or deactivate the personalisation
function.
Rear auto wipe in reverse: Activate
or deactivate automatic switching
on of the rear window wiper when
reverse gear is engaged.
■ Park assist / Collision detection
Park assist: Activate or deactivate
the ultrasonic parking assist .
■ Exterior ambient lighting
Duration upon exit of vehicle:
Activate or deactivate and change
the duration of exit lighting.
Exterior lighting by unlocking:
Activate or deactivate the welcome
lighting.
■ Remote locking, unlocking, starting
Remote door unlock: Change the
configuration to unlock only the
driver's door or the whole vehicle
whilst unlocking.
■ Restore factory settings
Restore factory settings: Reset all
settings to the default settings.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
105
Personal settings in the
Colour-Info-Display
Press the CONFIG button. The menu
Settings is displayed.
The following settings can be
selected by turning and pressing the
multifunction knob:
■ Languages
■ Time & Date
■ Radio settings
■ Phone settings
■ Navigation settings
■ Vehicle settings
■ Display settings
In the corresponding submenus the
following settings can be changed:
Languages
Selection of the desired language.
Time & Date
See Clock 3 81.
Radio settings
See description for Infotainment
system in the Infotainment system
instruction.
Phone settings
See description for Infotainment
system in the Infotainment system
instruction.
Navigation settings
See description for Infotainment
system in the Infotainment system
instruction.
Vehicle settings
■ Climate and air quality
Auto fan speed: Modifies the fan
regulation.
Climate control mode: Activate or
deactivate cooling.
Auto rear demist: Automatic
activation of rear heated window.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
106
■ Comfort settings
Chime volume: Change the volume
of warning chimes.
Rear auto wipe in reverse: Activate
or deactivate automatic switching
on of the rear window wiper when
reverse gear is engaged.
■ Park assist / Collision detection
Park assist: Activate or deactivate
the ultrasonic parking assist.
■ Exterior ambient lighting
Duration upon exit of vehicle:
Activate or deactivate and change
the duration of exit lighting.
Exterior lighting by unlocking:
Activate or deactivate the welcome
lighting.
■ Restore factory settings
Restore factory settings: Reset all
settings to the default settings.
Display settings
Selectable display settings:
■ Day mode: Optimisation for
daylight conditions.
■ Night mode: Optimisation for
darkness.
■ Automatic mode:
Vehicles without light sensor:
The display changes the mode
when the vehicle lights are
switched on/off.
Vehicles with light sensor:
The display changes the mode due
to the exterior lighting conditions
independently from the vehicle
lights.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
107
Exterior lighting . . . . . . .. 107
Interior lighting . . . . . . ... 112
Lighting features . . . . . . 114
Exterior lighting
Turn light switch:
AUTO = automatic light control:
Headlights are switched
on and off automatically
depending on external
lighting conditions.
m
= activation or deactivation
of the automatic light
control. Switch turns back
to AUTO.
8
= sidelights
9
= headlights
Vehicles without automatic light
control:
7
= off
In the Driver Information Center with
Uplevel-Display, the current status of
the automatic light control is
displayed.
When switching on the ignition,
automatic light control is active.
Control indicator 8 3 93.
Tail lights
Tail lights are illuminated together
with headlights and sidelights.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
108
Automatic light control function
When the automatic light control
function is switched on and the
engine is running, the system
switches between daytime running
light and automatic headlight
depending on lighting conditions.
Daytime running light
Daytime running light increases
visibility of the vehicle during daylight.
While the daytime running light is
active, the tail lights are switched on
or off depending on country-specific
variant.
Automatic headlight activation
During poor lighting conditions the
headlights are switched on.
Tunnel detection
When a tunnel is entered the
headlights are switched on.
Adaptive forward lighting 3 110.
To switch from low to high beam,
push lever.
To switch to low beam, push lever
again or pull.
To activate the headlight flash, pull
lever.
Instruction headlight range
adjustment
-------------------------------------------------------------------------------------------------------------------------------------------------------------
109
To adapt headlight range to the
vehicle load to prevent dazzling: turn
thumb wheel ? to required position.
0 = front seats occupied
1 = all seats occupied
2 = all seats occupied and load
compartment laden
3 = driver's seat occupied and load
compartment laden.
The asymmetrical headlight beam
extends visibility at the edge of the
road at the passenger side.
However, when driving in countries
where traffic drives on the opposite
side of the road, adjust the headlights
to prevent dazzling of oncoming
traffic.
Vehicles without Adaptive
Forward Lighting
Turn the adjusting screws with the
screwdriver clockwise for half a turn.
The adjusting screws are located at
the headlights above the low beam
caps 3 152.
For deactivation turn the adjusting
screws anticlockwise for half a turn.
Have the adjustment of the
headlights checked after
deactivation.
We recommend consulting
a workshop.
Vehicles with Adaptive Forward
Lighting
1. Key in ignition switch.
2. Pull turn signal lever and hold
(headlight flash).
-------------------------------------------------------------------------------------------------------------------------------------------------------------
110
3. Switch on ignition.
4. After approx. 5 seconds the
control indicator f starts flashing
and an acoustic signal sounds.
Control indicator f 3 93.
Every time the ignition is switched on,
f
flashes as a reminder for approx.
4 seconds.
For deactivation operate the same
procedure as described above. f will
not flash when function is
deactivated.
Adaptive forward lighting ensures
better illumination of bends, crossings
and narrow bends.
Curve lighting
The light beam pivots based on
steering wheel position and speed.
Corner lighting
On tight bends or when turning off,
depending on the steering angle or
the indicator light signal, an additional
left or right reflector is switched on
which illuminates the road in the
direction of travel. It is activated up to
a speed of 40 km/h.
Reversing function
If the headlights are on and reverse
gear is engaged, both corner lights
are switched on. They remain
illuminated for 20 seconds after
disengaging reverse gear or until
driving faster than 17 km/h forward.
Operated with the ¨ button.
In the event of an accident with airbag
deployment the hazard warning
flashers are activated automatically.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
111
lever up
= right turn signal
lever down = left turn signal
If the lever is moved past the
resistance point, the turn signal is
switched on constantly. When the
steering wheel moves back, the turn
signal is automatically deactivated.
For three flashes, e.g. when changing
lanes, press the lever until resistance
is felt and then release.
With a trailer connected, turn signal
flashes six times when pressing the
lever until resistance is felt and then
releasing.
Move the lever to the resistance point
and hold for longer indication.
Switch the turn signal off instructionly by
moving the lever to its original
position.
Operated with the > button.
Light switch in position AUTO:
switching on front fog lights will switch
headlights on automatically.
Operated with the r button.
Light switch in position AUTO:
switching on rear fog light will switch
headlights on automatically.
Light switch in position 8: rear fog
light can only be switched on with
front fog lights.
The vehicle rear fog light is
deactivated when towing.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
112
When the vehicle is parked, the
parking lights on one side can be
activated:
1. Switch off ignition.
2. Move turn signal lever all the way
up (right parking lights) or down
(left parking lights).
Confirmed by a signal and the
corresponding turn signal control
indicator.
The reversing light comes on when
the ignition is on and reverse gear is
selected.
The inside of the light housing may
mist up briefly in poor, wet and cold
weather conditions, in heavy rain or
after washing. The mist disappears
quickly by itself; to help switch on the
headlights.
Interior lighting
Brightness of the following lights can
be adjusted when the exterior lights
are on:
■ Instrument panel illumination
■ Info-Display
■ Illuminated switches and operation
elements
Turn thumb wheel A until the required
brightness is obtained.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
113
On vehicles with light sensor the
brightness can only be adjusted when
the exterior lights are on and the light
sensor detects night conditions.
During entry and exit of the vehicle,
the front and rear courtesy lights
automatically switch on and then off
after a delay.
In the event of an accident with
airbag deployment the courtesy
lights are turned on automatically.
Front courtesy light
Operate rocker switch:
w
= automatic switching on
and off.
press u = on.
press v = off.
Rear courtesy lights
Illuminate in conjunction with the front
courtesy light depending on rocker
switch position.
Operated with s and t buttons in
front and rear courtesy lights.
Illuminate when the cover is opened.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст