Suzuki Grand Vitara JB416 / JB420. Service manual — part 107
![](/vehicle/himayebi/barastiadin/singoutays/kstijuer.png)
1D-96 Engine Mechanical: For J20 Engine
Camshafts, Tappet and Shim Removal and
Installation
S5JB0A1426030
CAUTION
!
• Keep working table, tools and hands clean
while overhauling.
• Use special care to handle aluminum parts
so as not to damage them.
• Do not expose removed parts to dust.
Keep them always clean.
Removal
1) Remove 2nd timing chain. Refer to “2nd Timing
Chain and Chain Tensioner Removal and
Installation: For J20 Engine” for removal.
2) Loosen camshaft housing bolts in such order as
indicated in figure and remove them.
3) Remove camshaft housings.
4) Remove camshafts.
5) Remove tappets with shims.
Installation
1) Apply engine oil around tappet (1), and then install
tappets with shims to cylinder head.
NOTE
When installing shim, make sure to direct
shim No. side toward tappet.
2) Match match mark (1) on crank timing sprocket and
mating surface of cylinder block and lower
crankcase (2).
3) Install camshafts.
Apply oil to sliding surface of each camshaft and
camshaft journal then install them by aligning match
marks on cylinder head and camshafts as shown in
figure.
4) Install camshaft housing pins (3) as shown in figure.
“2”
“12” “13”
“20” “21”
“16” “17”
“6”
“10” “11”
“18” “19”
“14” “15”
“8”
“7”
“9”
“5”
“3”
“4”
“1”
I5JB0A142029-01
1
I5JB0A142030-01
1. Knock pin of intake camshaft
2. Knock pin of exhaust camshaft
3. Match mark of intake camshaft
4. Match mark of exhaust camshaft
1. Intake camshaft
2. Exhaust camshaft
I2RH01140103-01
I5JB0A142031-01
I4RH01140032-01
![](/vehicle/himayebi/barastiadin/singoutays/aysowingb.png)
Engine Mechanical: For J20 Engine 1D-97
5) Check position of camshaft housings.
Embossed marks are provided on each camshaft
housing, indicating position and direction for
installation. Install housings as indicated by these
marks.
6) After applying oil to housing bolts, tighten them
temporarily first. Then tighten them by following
numerical order in figure.
Tighten a little at a time and evenly among bolts and
repeat tightening sequence two or three times before
they are tightened to specified torque.
Tightening torque
Camshaft housing bolt (a): 11 N·m (1.1 kgf-m,
8.0 lb-ft)
7) Turn crankshaft clockwise then align crankshaft
timing sprocket key (1) with timing mark (2).
8) Install 2nd timing chain. Refer to “2nd Timing Chain
and Chain Tensioner Removal and Installation: For
J20 Engine” for installation.
9) Install timing chain cover. Refer to “Timing Chain
Cover Removal and Installation: For J20 Engine” for
installation.
10) Install cylinder head cover. Refer to “Cylinder Head
Cover Removal and Installation: For J20 Engine” for
installation.
11) Install oil pan. Refer to “Oil Pan and Oil Pump
Strainer Removal and Installation: For J20 Engine in
Section 1E” for installation.
12) Install engine assembly to vehicle referring to
“Engine Assembly Removal and Installation: For J20
Engine”.
13) Check valve lashes referring to “Valve Lash
(Clearance) Inspection: For J20 Engine”.
Camshaft, Tappet and Shim Inspection
S5JB0A1426031
Cam Wear
Using a micrometer, measure cam height. If measured
height is below its limit, replace camshaft.
Cam height “a”
1. I: Intake side or E: Exhaust side
2. Position from timing chain side
3. Pointing to timing chain side
I2RH01140106-01
“20”, (a)
“10”, (a)
“9”, (a)
“2”, (a)
“1”, (a)
“6”, (a)
“16”, (a)
“15”, (a)
“13”, (a)
“17”, (a)
“19”, (a)
“18”, (a)
“5”, (a)
“12”, (a)
“21”, (a)
“11”, (a)
“4”, (a)
3”, (a)
“8”, (a)
“14”, (a)
“7”, (a)
I5JB0A142032-01
Cam
height
Standard
Limit
Intake
cam
45.669 – 45.829 mm
(1.798 – 1.8043 in.)
45.550 mm
(1.793 in.)
Exhaust
cam
45.550 – 45.710 mm
(1.7933 – 1.7996 in.)
45.430 mm
(1.789 in.)
I5JB0A142033-01
I5JB0A142034-01
![](/vehicle/himayebi/barastiadin/singoutays/vestohoz.png)
1D-98 Engine Mechanical: For J20 Engine
Camshaft Runout
Set camshaft between two “V” blocks, and measure its
runout by using a dial gauge.
If measured runout exceeds the specified limit, replace
camshaft.
Runout limit
0.03 mm (0.0012 in.)
Camshaft Journal Wear
Check camshaft journals and camshaft housings for
pitting, scratches, wear or damage.
If any malcondition is found, replace camshaft or cylinder
head with housing. Never replace cylinder head without
replacing housings.
Check clearance by using gauging plastic. Checking
procedure is as follows.
1) Clean housings and camshaft journals.
2) Make sure that all tappets with shims are removed
and install camshafts to cylinder head.
3) Place a piece of gauging plastic to full width of
journal of camshaft (parallel to camshaft).
4) Install camshaft housing.
5) Tighten camshaft housing bolts in such order as
indicated in figure a little at a time till they are
tightened to specified torque.
NOTE
Do not rotate camshaft while gauging plastic
is installed.
Tightening torque
Camshaft housing bolt (a): 11 N·m (1.1 kgf-m,
8.0 lb-ft)
6) Remove housing, and using scale (2) on gauging
plastic envelop (1), measure gauging plastic width at
its widest point.
Journal clearance
I2RH01140109-01
IYSQ01143105-01
Standard
Limit
0.020 – 0.074 mm (0.0008 –
0.0029 in.)
0.12 mm (0.0047 in.)
“20”, (a)
“10”, (a)
“9”, (a)
“2”, (a)
“1”, (a)
“6”, (a)
“16”, (a)
“15”, (a)
“13”, (a)
“17”, (a)
“19”, (a)
“18”, (a)
“5”, (a)
“12”, (a)
“21”, (a)
“11”, (a)
“4”, (a)
“3”, (a)
“8”, (a)
“14”, (a)
“7”, (a)
I5JB0A142035-02
IYSQ01143107-01
![](/vehicle/himayebi/barastiadin/singoutays/keaa.png)
Engine Mechanical: For J20 Engine 1D-99
If measured camshaft journal clearance exceeds
limit, measure journal (housing) bore and outside
diameter of camshaft journal. Replace camshaft or
cylinder head assembly whichever the difference
from specification is greater.
Camshaft journal
Wear of Tappet and Shim
Check tappet and shim for pitting, scratches, or damage.
If any malcondition is found, replace.
Measure cylinder head bore and tappet outside diameter
to determine cylinder head-to-tappet clearance. If
clearance exceeds limit, replace tappet or cylinder head.
Cylinder head bore and tappet outside diameter
Oil Relief Valve
Check oil relief valve for clogging and ball for being
stuck.
Item
Standard
Camshaft journal bore
diameter. (IN & EX) [A]
26.000 – 26.033 mm
(1.0236 – 1.0249 in.)
Camshaft journal O.D. (IN &
EX) [B]
25.959 – 25.980 mm
(1.0221 – 1.0228 in.)
I5JB0A142036-01
I2RH0B140085-01
Item
Standard
Limit
Tappet outside
diameter [A]
32.456 – 32.472 mm
(1.2778 – 1.2784 in.)
—
Cylinder head bore
[B]
32.500 – 32.525 mm
(1.2795 – 1.2805 in.)
—
Cylinder head to
tappet clearance
0.028 – 0.069 mm
(0.0011 – 0.0027 in.)
0.15 mm
(0.0059 in.)
I5JB0A142038-01
I2RH01140111-01
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст