Suzuki Grand Vitara JB419. Service manual — part 52
Engine Mechanical: 1D-54
4) Install bearing cap referring to connecting rod and
bearing cap referring to Step 9) of “Installation” under
“Piston, Piston Ring and Connecting Rod Removal
and Installation”.
5) Remove cap, and using a scale (1) on gauging
plastic envelope (2), measure gauging plastic (2)
width at the widest point (clearance).
If measured clearance is out of specification, use a
new connecting rod bearing.
After install new bearing, recheck clearance.
Connecting rod bearing clearance
0.027 – 0.086 mm (0.00107 – 0.00338 in.)
6) If clearance can not be brought to its specification
even by using a new connecting rod bearing and/or
replace crankshaft.
Piston Protrusion
1) Install piston and connecting rod assembly to
cylinder block referring to Step 1) through 9) of
“Install” under “Piston, Piston Ring and Connecting
Rod Removal and Installation”.
2) Using special tool and dial gauge, measure piston
protrusion at specified position (2) as shown in figure
when piston (1) reaches top dead center. Repeat this
procedure with each piston.If measured protrusion is
out of specification, proceed to next step.
Piston protrusion
“a”: 0.50 – 0.62 mm (0.0197 – 0.0244 in.)
3) Check connecting rod length referring to
“Connecting Rod and Related Parts Specification
(for Reference)” under “Cylinders, Pistons and
Piston Rings Inspection”.If connecting rod is normal,
proceed to next step.
4) Replace piston (1) as follows in order to adjust piston
protrusion to specified value.
a) Remove piston, and measure the following
specification.
• Piston pin hole diameter “b”
• Distance “c” between top of piston and top of
piston pin hole
b) Obtain distance “d” between top of piston and
center of piston pin hole by formula below.
“d” = “b” / 2 + “c”
c) Using piston protrusion “a” measured at Step 2),
obtain adjusting distance “e” by formula below.
“e” = “d” + 0.56 mm (0.0220 in.) – “a”
Example:
When distance “d” of removed piston is 47.026
mm (1.85142 in.), and measured piston
protrusion “a” is 0.45 mm (0.0177 in.)
Calculated adjusting distance “e” = 47.026 mm
(1.85142 in.) + 0.56 mm (0.0220 in.) – 0.45 mm
(0.0177 in.) = 47.136 mm (1.85575 in.)
I2RH0B140123-01
2
1
I5JB0B140109-01
I5JB0B140110-01
1D-55 Engine Mechanical:
d) Select new piston so that distance “e” is within
range of distance “d” of new piston.
NOTE
Piston class (1) is marked on piston top as
shown in figure.
Available new piston class
e) Replace piston with selected piston.
f) Check piston protrusion, again.
Main Bearing, Crankshaft and Cylinder Block Component
S5JB0B1406068
Piston class (1)
Distance “d”
S
47.026 – 47.066 mm
(1.85142 – 1.85299 in.)
T
47.068 – 47.108 mm
(1.85307 – 1.85464 in.)
U
47.110 – 47.150 mm
(1.85473 – 1.85629 in.)
I5JB0B140132-01
1
5
7
3
2
(a)
6
6
4
3
I5JB0B140111-01
1. Cylinder block
6. Oil jet
2. Flywheel side crankshaft oil seal
7. Bearing cap seal
3. Main bearing
: Do not apply oil between cylinder block and bearing and between, main bearing
cap and bearing.
: Tighten 20 N
⋅m (2.0 kgf-m, 14.5 lb-ft) and 62° by the specified
procedure.
4. Thrust bearing
: Do not reuse.
5. Main bearing cap
: Apply engine oil to inside / sliding surface.
Engine Mechanical: 1D-56
Main Bearing, Crankshaft and Cylinder Block
Removal and Installation
S5JB0B1406066
Removal
1) Remove piston and connecting rod referring to
“Piston, Piston Ring and Connecting Rod Removal
and Installation”.
2) Remove heat exchanger referring to “Heat
Exchanger Removal and Installation in Section 1E”,
if necessary.
3) Loosen main bearing cap bolts in numerical order as
indicated in figure, and remove them.
4) Remove main bearing cap No.1 using special tool as
follows.
Special tool
(A): 09917–56510
a) Install special tool to main bearing cap No.1 (1).
b) Pull out main bearing cap No.1 from cylinder
block by tightening bolt (2) of special tool.
c) Remove main bearing cap from special tool.
5) Remove main bearing caps (No.2 through No.5) and
crankshaft from cylinder block.
6) Remove main bearings (1) and thrust bearings (2).
7) Disconnect fresh air vent hose (1), and remove oil
fresh air vent pipe (2) from cylinder block, if
necessary.
I5JB0B140112-01
I5JB0B140113-01
1
2
I5JB0B140114-01
1
2
I5JB0B140115-01
1D-57 Engine Mechanical:
8) Remove oil jet as follows, if necessary.
a) Pack rag into cylinder in order to prevent swart
from entering.
b) Remove spring stop (1) and spring (2) using 7
mm (0.28 in.) diameter drill (4).
CAUTION
!
Do not remove ball (3) to prevent swarf from
entering lubrication circuit.
c) Desorb swarf from cylinder and oil jet.
d) Install special tool (A) to drilled hole of oil jet (1).
e) Remove oil jets from cylinder using special tool
(A) and (B).
Special tool
(A): 09916–48120
(B): 09916–58120
Installation
NOTE
• Use new bearing cap bolts. They are
deformed after tightening once because
they are plastic deformation tightening
bolts.
• All parts to be installed must be perfectly
clean.
• Be sure to oil crankshaft journals, main
bearings and thrust bearings.
• Main bearings and bearing caps are in
combination sets.
Do not disturb such combination and make
sure that each part goes back to where it
came from, when installing.
1) Remove oil, old sealant and dust from mating
surface of cylinder block, bearing caps and
crankshaft.
2) Using special tool, install oil jets as follows, if
removed.
Special tool
(A): 09912–86510
(B): 09912–86520
I5JB0B140118-01
I5JB0B140116-01
1. Oil jet No.1
4. Oil jet No.4
7. Plate
2. Oil jet No.2
5. Flywheel side
8. Guide rod
3. Oil jet No.3
6. Pushrod
9. Plate bolt
I5JB0B140117-01
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст