Subaru Legacy (2005 year). Service manual — part 946

ET-17

ENTERTAINMENT

Navigation Body

16.Navigation Body

A: REMOVAL

1) Disconnect the ground cable from battery.
2) Remove the glove box. <Ref. to EI-51, REMOV-
AL, Glove Box.>
3) Remove the navigation body mounting screws in
numerical order and pull it out.

NOTE:
To remove the screw (4) easier, move the naviga-
tion body after removing the screw (3).

4) Remove the harness connector and antenna ca-
ble, and then remove the navigation body.

B: INSTALLATION

Install in the reverse order of removal.

ET-00107

(2)

(3)

(4)

(1)

ET-18

ENTERTAINMENT

Front Accessory Power Supply Socket

17.Front Accessory Power Sup-

ply Socket

A: REMOVAL

1. FRONT

1) Disconnect the ground cable from battery.
2) Remove the console front panel. <Ref. to EI-54,
REMOVAL, Center Console.>
3) Disconnect the harness connector, and remove
the accessory power supply socket.

2. REAR

1) Disconnect the ground cable from battery.
2) Remove the console box. <Ref. to EI-53, RE-
MOVAL, Console Box.>
3) Disconnect the harness connector, and remove
the accessory power supply socket.

B: INSTALLATION

Install in the reverse order of removal.

ET-00094

ET-00095

ET-19

ENTERTAINMENT

Steering Satellite Switch

18.Steering Satellite Switch

A: REMOVAL

1) Disconnect the ground cable from battery.
2) Set the tire to the straight-ahead position.
3) Remove the airbag module. <Ref. to AB-16, RE-
MOVAL, Driver’s Airbag Module.>

WARNING:
With the airbag module equipped, always refer
to “Airbag System” when performing the airbag
module repair service. <Ref. to AB-16, INSPEC-
TION, Driver’s Airbag Module.>

4) Remove the steering wheel. <Ref. to PS-21, RE-
MOVAL, Steering Wheel.>
5) Remove the cover from steering wheel.
6) Remove each one of satellite switch mounting
screw from the LH and RH side.

7) Remove the satellite switch.

B: INSTALLATION

Install in the reverse order of removal.

CS-00331

ET-20

ENTERTAINMENT

Steering Satellite Switch

C: INSPECTION

CS-00387

1

5

2 3 4

Step

Check

Yes

No

1

MUTE SWITCH CONTINUITY CHECK.
1) Press the mute switch.
2) Measure the resistance between satellite
switch connector terminals.

Terminals

No. 1 — No. 2:

Is the resistance approx. 22

Ω? Go to step 2.

Replace the satel-
lite switch.

2

VOLUME SWITCH CONTINUITY CHECK.
1) Press the volume switch.
2) Measure the resistance between satellite
switch connector terminals.

Terminals

No. 1 — No. 2: Volume up
No. 1 — No. 2: Volume down

Is the resistance approx. 90

Ω?

(Volume up) Is the resistance
approx. 200

Ω? (Volume down)

Go to step 3.

Replace the satel-
lite switch.

3

MODE SWITCH CONTINUITY CHECK.
1) Press the mode switch.
2) Measure the resistance between satellite
switch connector terminals.

Terminals

No. 1 — No. 2:

Is the resistance approx. 360
Ω?

Go to step 4.

Replace the satel-
lite switch.

4

SEEK SWITCH CONTINUITY CHECK.
1) Press the seek switch.
2) Measure the resistance between satellite
switch connector terminals.

Terminals

No. 1 — No. 2: Seek up
No. 1 — No. 2: Seek down

Is the resistance approx. 690
Ω? (Seek up) Is the resistance
approx. 1.5 k

Ω? (Seek down)

Go to step 5.

Replace the satel-
lite switch.

5

CHECK SATELLITE SWITCH INSULATION.
1) Not to operate the satellite switch.
2) Measure the resistance between satellite
switch connector terminals.

Terminals

No. 1 — No. 2:

Is the resistance approx. 4.7
k

Ω?

Satellite switch is
normal.

Replace the satel-
lite switch.