Subaru Impreza 3 / Impreza WRX / Impreza WRX STI. Service manual — part 391

CS-15

MT Gear Shift Lever

CONTROL SYSTEMS

5) Separate the gear shift lever and the stay.

6) Remove the O-ring and bushing from the gear

shift lever.

7) Remove the spring pin, and then remove the

bushing and snap ring.

8) Remove the boss from the joint.

9) Remove the bushing and spacer from the boss.

10) Remove the bushing and cushion rubber from

the stay.

(A) O-ring
(B) Bushing

(A) Spring pin
(B) Bushing

(C) Snap ring

CS-01413

CS-01415

(B)

(A)

(A)

CS-01414

(B)

(A)

(C)

(A) Bushing
(B) Spacer

(A) Bushing
(B) Stay

(C) Cushion rubber

CS-00322

CS-00238

(B)

(A)

(A)

CS-00058

(A)

(B)

(C)

CS-16

MT Gear Shift Lever

CONTROL SYSTEMS

D: ASSEMBLY

NOTE:

• Clean all the parts before assembly.

• Apply NIGTIGHT LYW No. 2 grease or equiva-

lent to each part. <Ref. to CS-3, 6MT GEAR SHIFT

LEVER, COMPONENT, General Description.>

1. STI MODEL

1) Mount the bushing and cushion rubber to the

stay.

2) Install the bushing and spacer to boss.

3) Install the snap ring to gear shift lever and install

the bushing.
NOTE:

Apply grease to the bushing.

4) Apply grease to the bushing and O-ring, and

then install to gear shift lever.

5) Apply sufficient grease into boss, and then install

the gear shift lever to the stay.

(A) Bushing
(B) Stay

(C) Cushion rubber

(A) Bushing
(B) Spacer

CS-00239

(B)

(C)

(A)

CS-00238

(B)

(A)

(A)

(A) Bushing
(B) Snap ring

(A) O-ring
(B) Bushing

CS-00237

(A)

(B)

CS-00236

(A)

(B)

(A)

CS-00235

CS-17

MT Gear Shift Lever

CONTROL SYSTEMS

6) Install the snap ring.

7) Insert the gear shift lever and rod into boot hole.

8) Install the rod.
Tightening torque:

12 N·m (1.2 kgf-m, 8.9 ft-lb)

9) Install the boss to the rod.
Tightening torque:

12 N·m (1.2 kgf-m, 8.9 ft-lb)

10) Install a new lock wire.

NOTE:

• Install the lock wire to the stay groove.

• Bend the extra wire to the same direction of lock

wire winding.

(A) Snap ring

(A) Rod
(B) Lever

(C) Stay

(A) Rod
(B) Boss

CS-00234

(A)

CS-00233

(C)

(A)

(B)

CS-00232

(B)

(A)

(A) Lock wire

(A) Inner boot
(B) Lock wire

(C) Stay

CS-00231

(A)

CS-00240

(A)

(A)

(B)

(B)

B

B

(B)

B - B

(C)

CS-18

MT Gear Shift Lever

CONTROL SYSTEMS

11) Install the holder.
Tightening torque:

1.3 N·m (0.1 kgf-m, 1.0 ft-lb)

12) Insert the reverse check cable into the boot

hole.

13) Insert the reverse check cable into the gear

shift assembly, and fix in place with a band clip.
NOTE:

• Cut the excess band clip.

• Make sure that the reverse check cable is insert-

ed into the gearshift lever with no gaps.

14) Install the seat cushion and spring.

15) Use the spring pin to secure the end of the slid-

er and reverse check cable.
NOTE:

Apply grease to the moving part of slider.

16) Install the reverse check cable to the cable

plate, and tighten the lock nut.
Tightening torque:

6 N·m (0.6 kgf-m, 4.4 ft-lb)

17) Secure the reverse check cable to the stay clip.
NOTE:

Install the reverse check cable on top of the stay.

(A) Holder

(A) Spring
(B) Seat cushion

(A)

CS-00230

CS-00227

CS-00241

(A)

(B)

(A) Slider
(B) Spring pin

(A) Cable plate
(B) Reverse check cable

(A) Reverse check cable
(B) Clip

CS-00225

(A)

(B)

CS-00228

(A)

(B)

CS-00243

(A)

(B)