Chevrolet Silverado / GMC Sierra. Service manual — part 793
1-2-3-4 AND 3-5 REVERSE CLUTCH BEARING ASSEMBLY REPLACEMENT
Fig. 156: Replacing 1-2-3-4 and 3-5 Reverse Clutch Bearing Assembly
Courtesy of GENERAL MOTORS CORP.
1-2-3-4 and 3-5 Reverse Clutch Bearing Assembly Replacement
6
Tip: After the retaining ring is installed, determine
clutch piston travel in order to verify if the correct
selective retaining ring is being used. Refer to 3-5
Reverse Clutch Backing Plate Retaining Ring
Measurement (6L80/6L90).
clutch assembly.
Callout
Component Name
3-5 Reverse Clutch Bearing
2008 Chevrolet Silverado 1500
2008 TRANSMISSION Automatic Transmission - 6L50/6L80/6L90 - Cab & Chassis Sierra, Cab & Chassis Silverado,
Sierra & Silverado
1-2-3-4 AND 3-5 REVERSE CLUTCH OVERHAUL (6L90)
1-2-3-4 AND 3-5 REVERSE CLUTCH PLATES REMOVAL
1
Specification: Install the bearing flush to 0.3 mm
below the thrust surface.
Special Tools
DT 47865 Bearing Remover. See Special
Tools.
DT 47866 Bearing Installer. See Special
Tools.
J 8092 Driver Handle
J 45124 Removal Bridge. See Special Tools.
NOTE:
Install the NEW bearing assembly with the seal side
up. Improper installation of the bearing may cause
damage to the transmission.
NOTE:
Do not reuse the bearing. Install a NEW bearing.
Reusing an old bearing may cause damage to the
transmission.
2008 Chevrolet Silverado 1500
2008 TRANSMISSION Automatic Transmission - 6L50/6L80/6L90 - Cab & Chassis Sierra, Cab & Chassis Silverado,
Sierra & Silverado
Fig. 157: 1-2-3-4 and 3-5 Reverse Clutch Plates Removal
Courtesy of GENERAL MOTORS CORP.
1-2-3-4 and 3-5 Reverse Clutch Plates Removal
Callout
Component Name
1
3-5 Reverse Clutch Backing Plate Retaining
Ring
2
3-5 Reverse Clutch Backing Plate
3
3-5 Reverse Clutch Plate Assembly (Qty: 5)
4
3-5 Reverse Clutch Plate (Qty: 5)
5
3-5 Reverse Clutch (Waved) Plate
6
3-5 Reverse Clutch Apply Ring
7
1-2-3-4 Clutch Backing Plate Retaining Ring
2008 Chevrolet Silverado 1500
2008 TRANSMISSION Automatic Transmission - 6L50/6L80/6L90 - Cab & Chassis Sierra, Cab & Chassis Silverado,
Sierra & Silverado
1-2-3-4 CLUTCH PISTON REMOVAL
Fig. 158: Removing 1-2-3-4 Clutch Piston
Courtesy of GENERAL MOTORS CORP.
8
1-2-3-4 Clutch Backing Plate
9
1-2-3-4 Clutch Plate Assembly (Qty: 6)
10
1-2-3-4 Clutch Plate (Qty: 6)
11
1-2-3-4 Clutch (Waved) Plate
2008 Chevrolet Silverado 1500
2008 TRANSMISSION Automatic Transmission - 6L50/6L80/6L90 - Cab & Chassis Sierra, Cab & Chassis Silverado,
Sierra & Silverado
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст