Chevrolet Silverado / GMC Sierra. Service manual — part 2922
Circuit/System Description
This DTC indicates and RAM/ROM checksum, a EEPROM failure, or an ECU malfunction due
to an internal microprocessor failure.
Conditions for Running the DTC
The ignition is ON.
System voltage is 10.5-18 volts.
Conditions for Setting the DTC
The EEPROM, RAM and ROM, and ECM Microprocessor do self checks against one another
and the data does not match causing the DTC to set.
Action Taken When the DTC Sets
Shifting is still disabled until the DTC has cleared itself.
The SERVICE 4WD indicator remains illuminated for the remainder of the current ignition
cycle.
Conditions for Clearing the DTC
The transfer case shift control module clears the DTC if the condition for setting the DTC is
not currently present.
A history DTC clears after 40 consecutive warm up cycles without a fault present.
History DTCs can be cleared using a scan tool.
Reference Information
Schematic Reference
Transfer Case Control Schematics
Connector End View Reference
Component Connector End Views
Electrical Information Reference
Circuit Testing
Connector Repairs
2008 Chevrolet Silverado 1500
2008 TRANSMISSION Transfer Case - MP 3023/3024-NQH - Cab & Chassis Sierra, Cab & Chassis Silverado, Sierra &
Silverado
Testing for Intermittent Conditions and Poor Connections
Wiring Repairs
Scan Tool Reference
Scan Tool Data List
Scan Tool Data Definitions
Diagnostic Aids
It is sometimes possible to set this DTC falsely due to low voltage. Attempt to clear this DTC and
retest.
Circuit/System Testing
If this DTC sets attempt to clear the DTC and Retest.
If the DTC is cleared, but then resets then replace the transfer case control module,
program, and complete the transfer case motor learn procedure.
Repair Procedures
Perform the Diagnostic Repair Verification after completing the diagnostic procedure.
Control Module References for TCSCM replacement, setup, and programming
Transfer Case High/Low Clutch Reset
DTC C0569
Diagnostic Instructions
Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
Review Strategy Based Diagnosis for an overview of the diagnostic approach.
Diagnostic Procedure Instructions provides an overview of each diagnostic category.
DTC Descriptor
DTC C0569 4B
System Configuration Error Calibration Data Not Learned
Diagnostic Fault Information
2008 Chevrolet Silverado 1500
2008 TRANSMISSION Transfer Case - MP 3023/3024-NQH - Cab & Chassis Sierra, Cab & Chassis Silverado, Sierra &
Silverado
Circuit/System Description
This DTC is set anytime a new transfer case shift control module is installed. The transfer case
motor learn procedure must be performed to erase this DTC. The DTC must learn the amount of
clutch tolerance depending on clutch stackup and the amount of wear the clutches have
accumulated.
Conditions for Running the DTC
The ignition is ON.
System voltage is 10.5-18 volts.
Conditions for Setting the DTC
The motor learn procedure for a new module has not been performed.
Action Taken When the DTC Sets
Shifting is still disabled until the motor learn procedure has been performed.
The SERVICE 4WD indicator does not light for this DTC.
Conditions for Clearing the DTC
The transfer case shift control module clears the DTC if the motor learn procedure has been
successfully performed.
Reference Information
Schematic Reference
Transfer Case Control Schematics
Connector End View Reference
Component Connector End Views
Circuit
Short to
Ground
Open/High
Resistance
Watchdog/Safety
Failure
Internal
Electronic
Failure
Electronic Control Unit
Malfunction
-
-
DTC C0550 39
DTC C0550
39
2008 Chevrolet Silverado 1500
2008 TRANSMISSION Transfer Case - MP 3023/3024-NQH - Cab & Chassis Sierra, Cab & Chassis Silverado, Sierra &
Silverado
Electrical Information Reference
Circuit Testing
Connector Repairs
Testing for Intermittent Conditions and Poor Connections
Wiring Repairs
Scan Tool Reference
Scan Tool Data List
Scan Tool Data Definitions
Diagnostic Aids
Perform the motor learn procedure before normal operation will occur.
Circuit/System Testing
Perform the motor learn procedure.
Repair Procedures
Perform the Diagnostic Repair Verification after completing the diagnostic procedure.
Transfer Case High/Low Clutch Reset
DTC C0896
Diagnostic Instructions
Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
Review Strategy Based Diagnosis for an overview of the diagnostic approach.
Diagnostic Procedure Instructions provides an overview of each diagnostic category.
DTC Descriptor
DTC C0896 03
Device Voltage Range Voltage Below Threshold
DTC C0896 07
2008 Chevrolet Silverado 1500
2008 TRANSMISSION Transfer Case - MP 3023/3024-NQH - Cab & Chassis Sierra, Cab & Chassis Silverado, Sierra &
Silverado
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст