Chevrolet Silverado / GMC Sierra. Service manual — part 2871

All shifting is disabled.

The SERVICE 4WD indicator remains illuminated for the remainder of the current ignition
cycle.

Conditions for Clearing the DTC

The transfer case shift control module clears the DTC if the condition for setting the DTC is
not currently present.

A history DTC clears after 40 consecutive warm up cycles without a fault present.

History DTCs can be cleared using a scan tool.

Reference Information

Schematic Reference

Transfer Case Control Schematics

Connector End View Reference

Component Connector End Views

Electrical Information Reference

Circuit Testing

Connector Repairs

Testing for Intermittent Conditions and Poor Connections

Wiring Repairs

Scan Tool Reference

Scan Tool Data List

Scan Tool Data Definitions

Diagnostic Aids

A short to ground on the neutral indicator control circuit will cause the neutral indicator to
remain on at all times. An open or high resistance will cause the neutral indicator to be
inoperative during the 2 second bulb check.

Circuit/System Testing

2008 Chevrolet Silverado 1500

2008 TRANSMISSION Transfer Case - MP 1625/1626-NQF - Cab & Chassis Sierra, Cab & Chassis Silverado, Sierra &

Silverado

The 5-volt reference circuit and the switch signal will have to be checked for shorts to ground,
opens, high resistance, and shorts to voltage by following the below listed steps.

1. Reference the mode switch supply voltage with a scan tool.

The scan tool should indicate 4.8-5.2 volts. If the scan tool indicates the voltage is
within this specification then with a jumper wire short the switch signal circuit pin 12
on the switch to the 5-volt reference circuit pin 11 on the switch. If the mode switch
return voltage on the scan tool measures 4.8-5.2 volts then replace the switch.

2. If the mode switch return does not read 4.8-5.2 volts check the switch signal circuit and the

5-volt reference circuits for a short to ground, short to voltage, open, or high resistance.

If no shorts or high resistance are found on the switch signal or 5-volt reference
circuits then replace the transfer case shift control module, reprogram, and complete
the motor learn procedure.

Repair Procedures

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.

Transfer Case Shift Control Switch Replacement (Without SLT) or Transfer Case
Shift Control Switch Replacement (With SLT)

Control Module References for TCSCM replacement, setup, and programming

Transfer Case High/Low Clutch Reset

DTC C0306

Diagnostic Instructions

Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.

Review Strategy Based Diagnosis for an overview of the diagnostic approach.

Diagnostic Procedure Instructions provides an overview of each diagnostic category.

DTC Descriptor

DTC C0306 02

Motor A or B Circuit Short to Ground

DTC C0306 05

Motor A or B Circuit Short to Battery or Open

2008 Chevrolet Silverado 1500

2008 TRANSMISSION Transfer Case - MP 1625/1626-NQF - Cab & Chassis Sierra, Cab & Chassis Silverado, Sierra &

Silverado

Diagnostic Fault Information

Circuit/System Description

The transfer case motor is a bi-directional, permanent magnet, DC motor. When energized,
through motor control A or motor control B, the ground is provided by the opposing motor
control circuit and then grounded through the transfer case shift control module ground circuit,
the motor, through a series of gears, rotates a shaft which moves the mode and range forks to shift
the transfer case between the following modes or ranges:

2HI

4HI

4LO

Neutral

This DTC detects an open, short to voltage, or short to ground in the motor control A or motor
control B circuits, or an open, or short to ground inside the motor.

Conditions for Running the DTC

The ignition is ON.

System voltage is 10.5-18 volts.

Conditions for Setting the DTC

The system tests the motor circuits by checking for unwanted voltage.

Then, the system supplies voltage on each of the motor circuits and reads the voltage back
on the other circuit.

If the system detects a condition with the circuits, the DTC is logged. The transfer case shift
control module senses a low voltage return in the motor control A or motor control B
circuits when a high voltage is expected.

The fault must remain current for 30 seconds to set the DTC.

Action Taken When the DTC Sets

Circuit

Short to

Ground

Open/High

Resistance

Short to

Voltage

Signal

Performance

Motor A or B Circuit

DTC C0306

02

DTC C0306

05

DTC C0306
05

-

2008 Chevrolet Silverado 1500

2008 TRANSMISSION Transfer Case - MP 1625/1626-NQF - Cab & Chassis Sierra, Cab & Chassis Silverado, Sierra &

Silverado

All shifting is disabled.

The SERVICE 4WD indicator remains illuminated for the remainder of the current ignition
cycle.

Conditions for Clearing the DTC

The transfer case shift control module clears the DTC if the condition for setting the DTC is
not currently present.

A history DTC clears after 40 consecutive warm up cycles without a fault present.

History DTCs can be cleared using a scan tool.

Reference Information

Schematic Reference

Transfer Case Control Schematics

Connector End View Reference

Component Connector End Views

Electrical Information Reference

Circuit Testing

Connector Repairs

Testing for Intermittent Conditions and Poor Connections

Wiring Repairs

Scan Tool Reference

Scan Tool Data List

Scan Tool Data Definitions

Diagnostic Aids

It is possible to have windings inside the motor shorted to the case resulting in a short to ground
causing this DTC to set.

Circuit/System Testing

The motor A control and motor B circuits need to be checked for shorts to ground, opens, high

2008 Chevrolet Silverado 1500

2008 TRANSMISSION Transfer Case - MP 1625/1626-NQF - Cab & Chassis Sierra, Cab & Chassis Silverado, Sierra &

Silverado