Peugeot 407 C Dag (2008 year). Manual — part 6

FILLING WITH FUEL

The fuel ﬁ ller ﬂ ap is electric, you can

only open it by pressing button A .

Button A is deactivated auto-
matically from 6 mph (10 km/h).

When ﬁ lling with fuel, the

engine must be switched off

with the ignition off:

Operating fault
A fuel gauge fault is indicated by the
fuel level indicator needle returning to
zero.
Consult a PEUGEOT dealer.

Fuel warning

 Turn the cap to the left.
 Remove the cap and hang the end

on the hook located on the inside

of the ﬂ ap.

A label afﬁ xed to the inside of the fuel

ﬁ ller ﬂ ap indicates which type of fuel

to use.
When you ﬁ ll your tank, do not con-

tinue after the third cut-off of the pump.
This could cause your vehicle to mal-
function.
The capacity of the tank is approxi-

mately 67 litres.


After ﬁ lling the tank, screw on the

cap and close the fuel ﬁ ller ﬂ ap.

Ensure that the fuel ﬁ ller ﬂ ap is

closed correctly.

When

this

warning

light

comes on in certain driving
conditions and depending
on the engine, the distance
which can be travelled with
the fuel remaining may be

less than 30 miles (50 kilometres).
Note: should you run out of fuel, you
must add at least 6 litres.

LIGHTS STALK

Lights off

Side lights

Dipped/main beam head-
lamps

Lights on
With the ignition and the automatic
lights function switched off, on open-
ing the driver's door a buzzer sounds
to warn you that you have left your
lights on.

Front and rear fog lamps (ring B)
 Turn ring B forwards to switch on

and backwards to switch off. The

position is conﬁ rmed by the light

on the instrument panel.

Front fog lamps (one press)

These operate with the side lights, dipped
headlamps or main beam headlamps.

Rear fog lamps (two presses)

These operate with the side lights and
the front fog lamps, or with the dipped
or main beam headlamps.

Left: downwards.
Right: upwards

Direction indicators (ﬂ ashers)

If you forget to return the di-
rection indicator to its normal
position, the volume of the au-
dible signal will increase, if you
are driving at a speed greater
than 45 mph (70 km/h).

Parking lights *
The side lights are lit on the side the

trafﬁ c is on for a few hours.
With the engine switched off and with-
in 45 seconds maximum, place the in-

dicator lights stalk on the trafﬁ c side

(for example: for parking on the right;
switching on of the lights on the left).
This is indicated by an audible sig-
nal and lighting of the corresponding
direction indicator on the instrument
panel for a few seconds.

If the parking lights are activat-
ed when your vehicle switches
to economy mode, they will re-
main on. However, you cannot

activate the parking lights if your ve-
hicle is already in economy mode.

Dipped/main beam change
 Pull the stalk fully towards you.

* According to version.

Automatic switching on of
the lights.

In the case of vehicles which

are not ﬁ tted with a lights stalk

with the "AUTO" position,
you can deactivate or activate

the automatic lighting via the multi-
function display "Personalisation-

Conﬁ guration" menu.

Front and rear lights (ring A)
 Turn ring A to the position re-

quired

The timed duration must also
be set, via the multifunction
display

"Personalisation-

Conﬁ guration" menu.

Automatic switching on of the

lights

To switch the function on
or off, use the multifunction
display "Personalisation-

Conﬁ guration" menu.

Activation

Deactivation

When this function is activa-
ted, the indicator light on the
instrument panel comes on.

When the function is deacti-
vated, the indicator light on the
instrument panel comes on.

Cancellation:


ﬂ ash the headlamps,

 get out of the vehicle and lock it.

Manual "follow-me-home" lighting
If the automatic switching on of the lights
is not activated, the manual "follow-me-
home" lighting can be activated.
When you leave your vehicle, the side
lights and dipped headlamps remain
on for approximately 1 minute.

Activation:
 switch off the engine,


ﬂ ash the headlamps,

 get out of the vehicle and lock it.

Deactivation:


ﬂ ash the headlamps again,

 get out of the vehicle and lock it.

Automatic "follow-me-home"

lighting
When you leave your vehicle with the

automatic switching on of the lights

activated , the side lights and dipped
headlamps remain on for the duration
selected when the ignition is switched
off.
To activate or deactivate this func-
tion, pass via the multifunction display

"Personalisation-Configuration"

menu.

In foggy weather, the bright-

ness sensor can detect sufﬁ -

cient light. As a consequence,
the lights will not come on au-
tomatically.

This function is active when the vehi-
cle is supplied to the customer.

If the brightness sensor does not

function correctly, if the system is

activated, the dipped headlamps and
the side lights come on.
Contact a PEUGEOT dealer to have
the system checked.

Daytime lights *

On vehicles which are equipped with
daytime lights, the dipped headlamps
come on when the vehicle is started.

The instruments and controls
(instrument panel, multifunc-
tion display, air conditioning
control panel, ...) are only lit

on switching to the automatic switch-
ing on of the lights mode or when the
lights are switched on manually.

This warning light comes on
on the instrument panel.

* According to country.

This function is available di-
rectly at the lights stalk on
certain versions depending on
the type of lights stalk.

The side lights and dipped beam head-
lamps switch on automatically if the light
is poor, or during operation of the wind-
screen wipers. They switch off as soon
as the light becomes bright enough or
the windscreen wipers stop.

The timed duration must also
be set, via the multifunction
display

"Personalisation-

Conﬁ guration" menu.

Automatic switching on of the

lights

To switch the function on
or off, use the multifunction
display "Personalisation-

Conﬁ guration" menu.

Activation

Deactivation

When this function is activa-
ted, the indicator light on the
instrument panel comes on.

When the function is deacti-
vated, the indicator light on the
instrument panel comes on.

Cancellation:


ﬂ ash the headlamps,

 get out of the vehicle and lock it.

Activation:
 switch off the engine,


ﬂ ash the headlamps,

 get out of the vehicle and lock it.

Deactivation:


ﬂ ash the headlamps again,

 get out of the vehicle and lock it.

Automatic "follow-me-home"

lighting
When you leave your vehicle with the

automatic switching on of the lights

"Personalisation-Configuration"

menu.

In foggy weather, the bright-

ness sensor can detect sufﬁ -

cient light. As a consequence,
the lights will not come on au-
tomatically.

This function is active when the vehi-
cle is supplied to the customer.

If the brightness sensor does not

function correctly, if the system is

activated, the dipped headlamps and
the side lights come on.
Contact a PEUGEOT dealer to have
the system checked.

Daytime lights *

On vehicles which are equipped with
daytime lights, the dipped headlamps
come on when the vehicle is started.

The instruments and controls
(instrument panel, multifunc-
tion display, air conditioning
control panel, ...) are only lit

on switching to the automatic switch-
ing on of the lights mode or when the
lights are switched on manually.

This warning light comes on
on the instrument panel.

* According to country.

This function is available di-
rectly at the lights stalk on
certain versions depending on
the type of lights stalk.

AUTOMATIC HEADLAMP
ADJUSTMENT

When stationary and when the vehi-

cle is moving, the system automatically

corrects the height of the beam, what-
ever the load of the vehicle. The driver
is then assured of having optimum light-
ing and not causing a nuisance to other
road users.

DIRECTIONAL HEADLAMPS

Activation/Deactivation

When the dipped or main beam head-
lamps are on, this function enables the
light beam to follow the direction of the
road.
The quality of your lighting when turning
is improved considerably.

In cases of malfunction,

the warning light comes on
on the instrument panel dis-
play, accompanied by an au-
dible signal and a message

on the multifunction display. The sys-
tem places your headlamps to the low
position.
Do not touch the xenon bulbs.
Consult a PEUGEOT dealer.

Function activated

Function deactivated

To deactivate or acti-
vate the function, go to
the

"Personalisation-

Conﬁ guration" menu on

your multifunction display.

When the engine is switched on, the
status of activation/deactivation of this
function selected when the engine was
switched off is retained.
By default, this function is activated.

Note: when stationary or dri-
ving at very low speed, or in
reverse gear, this function is
inactive.

In the event of a malfunc-

tion, this warning light ﬂ ash-

es on the instrument panel.

On vehicles ﬁ tted with daytime

lights, the function is only acti-
vated if the lights stalk is in the
dipped/main beam headlamps
position.

On starting, with the engine
running, the headlamps ini-
tialise automatically and per-
form a vertical sweep.

Consult a PEUGEOT dealer.

WINDSCREEN WIPER STALK

In the Intermittent position, the wiping
speed is in proportion to the speed of
the vehicle.
In the AUTO position, no further action
on your part is required.

Automatic windscreen wiper

The automatic wiping is controlled by a

rain sensor, ﬁ tted on the windscreen.
In AUTO mode, the wipers operate
automatically and

adjust their speed

to the intensity of the rainfall.

Activation

Deactivation

This warning light comes on
on the instrument panel, ac-
companied by a message
on the multifunction display,
when the driver presses the
wipers stalk down in AUTO
mode.

This warning light comes on
on the instrument panel, ac-
companied by a message
on the multifunction display,
when the driver moves the
wipers stalk to position I , 1
or 2 .

In the event of a malfunction, the

driver is informed of this by a message
on the multifunction display.
In AUTO mode, the wipers will then
operate in intermittent mode.
Contact a PEUGEOT dealer to have
the system checked.

Do not cover the rain sensor,
located on the windscreen
behind the interior mirror.

When using a car wash, switch off the
ignition.
In winter, it is advisable to wait until the
windscreen is completely clear of ice
before activating the automatic wipers.
When parking in snowy weather,
position the blades at the top of the
windscreen (maintenance position) to
prevent the accumulation of snow.

The wiping must be reacti-

vated if the ignition has been
switched off for more than one
minute .

Manual operation of the wipers stalk
by moving the lever A up and return-
ing it to position "0" cancels the AUTO
position, the deactivation warning light
comes on on the instrument panel dis-
play accompanied by a message on
the multifunction display.

Windscreen wipers
2

Fast wipe (heavy rain).

Normal wipe
(moderate rain).

Intermittent wipe

Off

AUTO 

Automatic wipe then single
sweep.

Maintenance position

This position enables the wiper blades
to be removed.
In the minute following switching off of
the ignition, any action on the wipers
stalk positions the wipers at the top
of the windscreen (parking in winter,
cleaning, replacement of the blades).
To reposition the wipers after this has
been done, switch on the ignition and
operate the stalk.

Windscreen and headlamp wash
Pull the windscreen wiper stalk to-
wards you. The windscreen wash then
the windscreen wipers operate for a

ﬁ xed period.
The headlamp wash is also activated,
if the headlamps are on .

Screenwash/headlamp

wash low

When the minimum level of
the reservoir is reached, this
warning light comes on, ac-
companied by an audible
signal and a message on the
multi-function display.

Next time you stop, ﬁ ll the screen-

wash/headlamp wash reservoir.
The warning light comes on each time
the stalk is operated, until the reser-

voir is ﬁ lled.

WINDSCREEN WIPER STALK

In the Intermittent position, the wiping
speed is in proportion to the speed of
the vehicle.
In the AUTO position, no further action
on your part is required.

Automatic windscreen wiper

The automatic wiping is controlled by a

rain sensor, ﬁ tted on the windscreen.
In AUTO mode, the wipers operate
automatically and

adjust their speed

to the intensity of the rainfall.

Activation

Deactivation

This warning light comes on
on the instrument panel, ac-
companied by a message
on the multifunction display,
when the driver presses the
wipers stalk down in AUTO
mode.

This warning light comes on
on the instrument panel, ac-
companied by a message
on the multifunction display,
when the driver moves the
wipers stalk to position I , 1
or 2 .

In the event of a malfunction, the

driver is informed of this by a message
on the multifunction display.
In AUTO mode, the wipers will then
operate in intermittent mode.
Contact a PEUGEOT dealer to have
the system checked.

Do not cover the rain sensor,
located on the windscreen
behind the interior mirror.

The wiping must be reacti-

vated if the ignition has been
switched off for more than one
minute .

Windscreen wipers
2

Fast wipe (heavy rain).

Normal wipe
(moderate rain).

Intermittent wipe

Off

AUTO 

Automatic wipe then single
sweep.

COURTESY LIGHTS

1. Front courtesy light

2. Front map reading lights

With the ignition on, operate the
relevant switch.

3. Rear courtesy light

4. Rear map reading lights

With the ignition on, operate the
relevant switch.

Deactivation
The courtesy lights can be deacti vated
by pressing switch 1 for more than
three seconds. Pressing switch 1 or
3

brieﬂ y switches the corresponding

courtesy light on and off.
The map reading lights are not affected
by this and can still be switched on.

Activation
To re-activate the automatic lighting,
press switch 1 again.

Sill illumination

The sill lighting is at the bottom of each
door trim.
The lights come on automatically
when a door is opened and switch off
automatically when all of the doors are
closed.

Boot light

The boot light is located in the right-
hand boot trim.
It comes on automatically when the
boot is opened and switches off auto-
matically when the boot is closed.

Pressing switch 1 or 3 switches on the
corresponding courtesy light for ten
minutes.
The front and rear courtesy lights come
on automatically when the ignition key
is removed, on unlocking the vehicle
or on opening one of the doors.
They gradually go off after the ignition
has been switched on or the vehicle
is locked.

SUN VISOR WITH
ILLUMINATED COURTESY
MIRROR

With the ignition on, the mirror is

auto matically lit up when the ﬂ ap is

opened.

AREAS FOR TOLL CARDS/
CAR PARK TICKETS

The athermic windscreen has two non-

reﬂ ective zones located either side of

the base of the interior mirror.

They are intended for afﬁ xing toll cards

and/or car park tickets.

AIR CONDITIONED GLOVE
BOX

This is ﬁ tted with a lock.

To open tshe glove box, lift the han-

dle.
The glove box is lit up when the cover

is opened.
The glove box has a vent A that can

be closed, which produces the same

conditioned air as the vents in the pas-

senger compartment.
In cold weather, it is recommended that

this vent is closed in order to conserve

the ambient air inside the passenger
compartment.
It also has a pen holder B and three
sockets * C

for connecting video equip-

ment.

* DT 16/9 colour screen only.

4 - Front armrest
To open the compartment, raise the

cover or operate the left ﬁ nger-plate

(according to version).
CDs and coins can be stored in this
compartment.

CENTRE CONSOLE

1 - Front ashtray (100 W max)
This is ﬁ tted with a lighter socket or a

12 volt socket.

Press the cover to open the ashtray.

To empty the ashtray, after opening,

grip the receptacle and remove it.

2 - 12 volt accessories socket

(100 W max)

This is a lighter type socket, ﬁ tted with

a cap. It is supplied with current from

the ignition on position.

3 - Storage container
This is located at the rear of the front

armrest.
To remove it, open it fully, press the

upper lug then pull to remove it.

5 - Retractable cup/can holder
This is located at the front of the front

armrest.
Press the cover to open the cup/can

holder.

Fitting/removing the mat

When removing the mat on the driver's

side, push the seat as far back as pos-

sible and remove the ﬁ xings.

When reﬁ tting, position the mat correc-

tly on the pin and clip the ﬁ xings. Check

that the mat is secured correctly.

Right-hand storage compartment

The right-hand storage compartment

(in the absence of the JBL Hi-Fi sys-

tem) can accommodate a box of bulbs,

a warning triangle and the luggage
retaining net.
To gain access to the compartment:
 turn the two screws to the right and

remove the panel.

Access to the ski flap

Tilt the rear armrest and pull the handle

down then towards you to open the ﬂ ap.

Luggage retaining net

Use the 4 lashing rings on the luggage

compartment ﬂ oor to secure your lug-

gage using the retaining net.

To prevent the mat from becom-

ing caught under the pedals:
-

only use mats suited to

the ﬁ xings already present

in the vehicle.It is impera-

tive that these ﬁ xings are

used.

- never ﬁ t one mat on top of another.

HORN

Press one of the spokes of the stee-
ring wheel.

HAZARD WARNING LIGHTS

Press the button, the direction indica-

tors ﬂ ash.
They can operate with the ignition off.

Automatic lighting of hazard
warning lights *

When braking in an emergency, de-
pending on the deceleration, the
hazard warning lights come on auto-
matically. They switch off automatically

the ﬁ rst time you accelerate.
It is also possible to switch them off by
pressing the button.

* According to country.

ELECTRONIC STABILITY
PROGRAMME (ESP)

The electronic stability programme
(ESP) incorporates the following sys-
tems:
-

the anti-lock braking system (ABS)
and the braking system (EBFD),

the emergency braking assistance
system,

the traction control (ASR),

the dynamic stability control (DSC).

Traction control (ASR)
The ASR system optimises traction in
order to avoid wheel slip by acting on
the brakes of the driving wheels and
on the engine. It also improves the
directional stability of the vehicle on
acceleration.

Dynamic stability control (DSC)
If there is a difference between the
path followed by the vehicle and that
required by the driver, the DSC moni-
tors each wheel and automatically acts
on the brake of one or more wheels
and on the engine to return the vehicle
to the required path, within the limits of
the laws of physics.

Operating modes

Definitions

Emergency braking assistance
system
In an emergency, this system ena-
bles you to reach the optimum braking
pressure more quickly and therefore
reduce the stopping distance.
It is triggered in relation to the speed
at which the brake pedal is pressed.
This is felt by a reduction in the resis-
tance of the pedal and an increase in
the effectiveness of the braking.

When this warning light
comes on, accompanied by
a buzzer and a message, it
indicates that there is a mal-
function of the ABS, which

can cause a loss of control of the vehi-
cle when braking.

When this warning light comes
on, connected to the STOP
and ABS warning lights,
accompanied by a buzzer
and a message, it indicates

that there is a malfunction of the elec-
tronic brake force distribution, which
can cause a loss of control of the vehi-
cle when braking.

Stop immediately.
In both cases, consult a PEUGEOT
dealer.

Anti-lock braking system (ABS)
and braking system (EBFD)
This system improves the stability and
manoeuvrability of your vehicle when
braking and offers improved control,
in particular on poor or slippery road
surfaces.
The ABS prevents wheel lock in the
event of emergency braking.
The braking system provides integral
management of the braking pressure
wheel by wheel.

Anti-lock braking system (ABS)
and braking system (EBFD)

Dynamic stability control (DSC)

When changing wheels (tyres
and rims), make sure that
these are approved.
Normal operation of the ABS

may make itself felt by slight vibrations
of the brake pedal.

In emergency braking, press

very ﬁ rmly without relea sing

the pressure.

Operating fault
When a system malfunction occurs,
the warning light comes on accompa-
nied by an audible signal and a mes-
sage on the multifunction display.
Contact a PEUGEOT dealer to have
the system checked.

The DSC offers improved
safety during normal driving
but should not encourage the
driver to take extra risks (late

braking) or drive at very high speeds.
Operation of the system is guaran-
teed on condition that the manufactu-
rer's instructions regarding the wheels
(tyres and rims), the braking compo-
nents, the electronic components and
the PEUGEOT network assembly and
maintenance/repair procedures are
complied with.
Following an impact, have the system
checked by a PEUGEOT dealer.

Warning light on the instrument
panel.

The indicator light comes on.

Deactivation
In exceptional conditions (starting the
vehicle when it is stuck in mud, immo-
bilised in snow, on unstable ground…),
it may prove useful to deactivate the
DSC.
 Press the "ESP OFF" switch, lo-

cated on the centre console.

The switch light and the indicator light
come on: the DSC no longer acts on
the operation of the engine.

Indicator light on the instrument
panel.

Reactivation
 Automatic when the ignition is

switched off,

 Automatic from 30 mph (50 km/h),
 Manual by pressing the switch

again.

Operation of the DSC

SEAT BELTS

Detection of fastening of the front

seat belts
When the ignition is switched on ,

if a front passenger has not fastened

his seat belt and if the vehicle speed

is below 13 mph (20 km/h) , you are

warned by lighting of the seat belt

warning light .
The warning light switches off when

the seat belt(s) concerned is(are) fas-

tened.
If the vehicle speed is above 13 mph

(20 km/h)

, you are warned by ﬂ ash-

ing of the seat belt warning light , an

audible signal and a message on the

multifunction display locating the un-

fastened seat belt(s).

Front seat belts with
pre-tensioner and force
limiter

In the event of a serious front impact,
the pre-tensioning system instantly

tightens the seat belts ﬁ rmly against

the bodies of the occupants.
The pre-tensioning seat belts are
armed when the ignition is on.
The force limiter reduces the pressure
of the seat belt against the chest of
the occupant, so increasing his pro-
tection.

Rear seat belts
The rear seats are each ﬁ tted with a

three-point inertia reel seat belt.
These seat belts have a force limiter.

To fasten the seat belts
 Pull the strap, then insert the

tongue into the buckle.

 Check that the seat belt is fastened

correctly by pulling the strap.

To unfasten the seat belts
 Press the red button on the buckle.

Note: a bag or an animal
placed on the front passenger
seat may trigger the lighting of
the warning light.

The audible signal ceases and the
warning light switches off when the
seat belt concerned is fastened.
After two minutes without any action

on the seat belts, the ﬂ ashing warning

light remains on permanently and the
audible signal ceases.
All of the warnings cease when a
door is opened or when the engine is
switched off.

Front seat belt height adjustment:
 To lower the attachment point,

squeeze control 1 and slide it
downwards.

 To raise the attachment point, slide

control 1 upwards.

Была ли эта страница вам полезна?

Да!Нет

9 посетителей считают эту страницу полезной.

Peugeot 407 C Dag (2008 year). Manual — part 6

Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.