Peugeot 308 (2017 year). Manual — part 3

31

1

Instruments

308_en_Chap01_instruments-de-bord_ed01-2016

Engine oil level indicator

On versions fitted with an electric oil gauge,
information on the conformity of the oil level
is displayed in the instrument panel for a few
seconds when the ignition is switched on, at
the same time as the service information.

the level read will only be correct if
the vehicle is on level ground and the
engine has been off for more than
30 minutes.

this is indicated by a message in the
instrument panel.

this is indicated by a message in the
instrument panel.
If the low oil level is confirmed by a check using
the dipstick, the level must be topped-up to
avoid damage to the engine.

this is indicated by a message in the
instrument panel. Contact a PeugeOt dealer
or a qualified workshop.

Dipstick

there are 2 marks on the
dipstick:
-

A = max; never exceed this
level,

-

B = min; top-up the level via
the oil filler, using the grade
of oil suited to your engine.

to locate the dipstick and the oil filler
cap on a Petrol engine or a Diesel
engine, refer to the corresponding
section.

Oil level correct

Oil level indicator fault

Oil level incorrect

32

Instruments

AdBlue

®

fluid range indicators

Once the AdBlue

®

tank is on reserve or after

detection of a fault with the SCR emissions
control system, when the ignition is switched
on an indicator displays an estimate of the
distance that can be covered, the range, before
engine starting is prevented.
In the event of simultaneous system fault and
low AdBlue

®

level, the shortest range figure is

the one displayed.

In the event of the risk of non-starting related to a lack of AdBlue

®

the engine start prevention system
required by regulations is activated
automatically once the AdBlue

®

tank is

empty.

Remaining range greater than 1 500 miles (2 400 km)

Pressing this button will display the remaining
range.

F then "Diagnostic".

Above 3 000 miles (5 000 km), the value is not
specified.

When switching on the ignition, there is no
automatic display of range in the instrument
panel.

the range at that moment is then displayed.

You can access this information in the touch
screen, if your vehicle has one.

F Select the "Driving assistance"

menu.

Remaining range between 350 and 1500 miles (600 and 2 400 km)

When switching on the ignition, the uReA
warning lamp comes on, accompanied
by an audible signal and the display of a
message (e.g. "top-up emissions additive:
Starting prevented in 900 miles") indicating
the remaining range expressed in miles or
kilometres.
When driving, the message is displayed every
200 miles (300 km) until the AdBlue

®

fluid has

been topped-up.
go to a PeugeOt dealer or a qualified
workshop to have the AdBlue

®

topped-up.

You can also top-up the tank yourself.

For more information on AdBlue

®

and

the SCR system, and topping-up in
particular, refer to the corresponding
section.

33

1

Instruments

308_en_Chap01_instruments-de-bord_ed01-2016

Remaining range between 0 and 350 miles (0 and 600 km)

When switching on the ignition, the SeRVICe
warning lamp comes on and the uReA warning
lamp flashes, accompanied by an audible
signal and the display of a message (e.g.
"top-up emissions additive: Starting prevented
in 350 miles") indicating the remaining range
expressed in miles or kilometres.
When driving, the message is displayed every
30 seconds until the AdBlue

®

fluid has been

topped-up.
go to a PeugeOt dealer or a qualified
workshop to have the AdBlue

®

topped-up.

You can also top-up the tank yourself.
Otherwise you will not be able to restart your
engine.

Breakdown related to a lack of AdBlue

®

additive

When switching on the ignition, the SeRVICe
warning lamp comes on and the uReA warning
lamp flashes, accompanied by an audible
signal and the display of the message "top-up
emissions additive: Starting prevented".
the AdBlue

®

tank is empty: the system required

by regulations prevents engine starting.

to be able to start the engine,
we recommend that you call on a
PeugeOt dealer or a qualified
workshop for the top-up required.
If you carry out the top-up yourself, it
is essential to add at least 3.8 litres of
AdBlue

®

to the tank.

For more information on AdBlue

®

and the SCR system, and topping-up in particular, refer

to the corresponding section.

34

Instruments

Starting prevented

every time the ignition is switched on, the SeRVICe
and engine diagnostic warning lamps come on and
the uReA warning lamp flashes, accompanied by
an audible signal and the display of the message
"emissions fault: Starting prevented".

You have exceeded the authorised
driving limit: the starting prevention
system inhibits engine starting.

to be able to start the engine, you must call on
a PeugeOt dealer or a qualified workshop.

In the event of a fault with the SCR emissions control system

A system that prevents engine starting is activated automatically from 650 miles (1 100 km) after confirmation of a fault with the SCR emissions
control system. Have the system checked by a PeugeOt dealer or a qualified workshop as soon as possible.

If it is a temporary fault, the alert
disappears during the next journey,
after self-diagnosis of the SCR system.

In the event of the detection of a fault

the uReA, SeRVICe and diagnostic warning
lamps comes on, accompanied by an audible
signal and the display of the message
"emissions fault".
the alert is triggered when driving when the
fault is detected for the first time, then when
switching on the ignition for subsequent
journeys, while the fault persists.

During an authorised driving phase (between
650 miles and 0 miles) (1 100 km and 0 km)

If a fault with the SCR system is confirmed (after
30 miles (50 km) covered with the permanent
display of the message signalling a fault), the
SeRVICe and engine diagnostic warning lamps
come on and the uReA warning lamp flashes,
accompanied by an audible signal and the
display of a message (e.g.: "emissions fault:
Starting prevented in 150 miles") indicating the
remaining range express in miles or kilometres.
While driving, the message is displayed every
30 seconds while the fault with the SCR system
persists.
the alert is repeated when switching on the
ignition.
You should go to a PeugeOt dealer or a
qualified workshop as soon as possible.
Otherwise, you will not be able to restart your
engine.

35

1

Instruments

308_en_Chap01_instruments-de-bord_ed01-2016

Distance recorders

the total and trip distances are displayed for
thirty seconds when the ignition is switched off,
when the driver's door is opened and when the
vehicle is locked or unlocked.

When travelling abroad, you may
have to change the units of distance:
the display of road speed must be in
the official units (miles or km) for the
country. the change of units is done via
the screen configuration menu, with the
vehicle stationary.

It measures the total distance travelled by the
vehicle since its first registration.

It measures the distance travelled since it was
reset to zero by the driver.
F With the ignition on, press the button until

zeros appear.

Total distance recorder

Trip distance recorder

36

Instruments

Lighting dimmer control

For the manual adjustment of the brightness of
the instrument panel and the touch screen.

With the exterior lighting on, press this button
to adjust the brightness of the dashboard
lighting, the touch screen and the mood
lighting. As soon as the lighting reaches the
required level of brightness, release the button.

F Press on the "Configuration" menu.
F Adjust the brightness (only on the touch

screen) by pressing on the "+" or "-" buttons.

Operates only when the vehicle's
exterior lighting is on.

Instrument panel

Touch screen

37

1

Instruments

308_en_Chap01_instruments-de-bord_ed01-2016

System that gives you information on the current journey (range, fuel consumption…).

trip computer

Instrument panel screen

Information display

F Press the button on the end of the wiper

control stalk to display the various tabs in
succession.

-

the current information tab with:
● the range,
● the current fuel consumption,
● the Stop & Start time counter.

- trip

"1" with:

● the average speed,
● the average fuel consumption,
● the distance travelled,
for the first trip.

- trip

"2" with:

● the average speed,
● the average fuel consumption,
● the distance travelled,
for the second trip.

Depending on version

Trip reset

F When the trip required is displayed, press

the control for more than two seconds
or use the left-hand thumbwheel of the
steering mounted controls.

trips "1" and "2" are independent but their use
is identical.
For example, trip "1" can be used for daily
figures, and trip "2" for monthly figures.

38

Instruments

trip computer

System that gives you information on the current journey (range, fuel consumption…).

Information display in the touch screen

Permanent display:
F Select the "Driving assistance" menu.
the trip computer information is displayed in
the primary page of the menu.
F Press one of the buttons to display the

desired tab.

the current fuel consumption tab
with:
-

the range,

-

the current fuel consumption,

-

the Stop & Start time counter.

the trip "1" tab with:
-

the distance travelled,

-

the average fuel consumption,

-

the average speed,

for the first trip.

the trip "2" tab with:
-

the distance travelled,

-

the average fuel consumption,

-

the average speed,

for the second trip.

Trip reset

F When the desired trip is displayed, press

the reset button or on the end of the wiper
control stalk.

trips "1" and "2" are independent but their use
is identical.
For example, trip "1" can be used for daily
figures, and trip "2" for monthly figures.

the information is accessible in the "Driving assistance" menu.

temporary display in a new window:
F Press the end of the wiper control stalk for

access to the information and display the
different tabs.

Touch screen

39

1

Instruments

308_en_Chap01_instruments-de-bord_ed01-2016

Trip computer, a few definitions

Range

(miles or km)
the distance which can still be
travelled with the fuel remaining in
the tank (related to the average fuel
consumption over the last few miles
(kilometres) travelled).

this value may vary following a change
in the style of driving or the relief,
resulting in a significant change in the
current fuel consumption.

When the range falls below 20 miles (30 km),
dashes are displayed. After filling with at least
5 litres of fuel, the range is recalculated and is
displayed when it exceeds 60 miles (100 km).

If dashes are displayed continuously
while driving in place of the digits,
contact a PeugeOt dealer or a
qualified workshop.

this function is only displayed from
20 mph (30 km/h).

Current fuel consumption

(mpg or l/100 km or km/l)
Calculated over the last few seconds.

Average fuel consumption

(mpg or l/100 km or km/l)
Calculated since the last trip
computer reset.

Average speed

(mph or km/h)
Calculated since the last trip
computer reset.

Distance travelled

(miles or km)
Calculated since the last trip
computer reset.

Stop & Start time
counter

(minutes / seconds or hours /
minutes)

A time counter calculates the time spent in
StOP mode during a journey.
It resets to zero every time the ignition is
switched on.

40

Instruments

touch screen

It gives access to:
-

the heating/air conditioning controls,

-

menus for adjusting settings for vehicle
functions and systems,

-

audio and display configuration menus,

-

audio system and telephone controls and
the display of associated information.

For reasons of safety, the driver
should only carry out operations
that require close attention, with the
vehicle stationary.
Some functions are not accessible
when driving.

General operation

Recommendations

It is necessary to press firmly, particularly for
"flick" gestures (scrolling through lists, moving
the map...).
A light wipe is not enough.
the screen does not recognise pressing with
more than one finger.
this technology allows use at all temperatures
and when wearing gloves.
Do not use pointed objects on the touch
screen.
Do not touch the touch screen with wet hands.
uses a soft clean cloth to clean the touch
screen.

And, depending on equipment, it allows:
-

the display of alert messages and the
visual parking sensors information,

-

access to the controls for the navigation
system and Internet services, and the
display of associated information.

State of indicator lamps

Some buttons contain an indicator lamp that
gives the state of the corresponding function.
green indicator: you have switched on the
corresponding function.
Orange indicator: you have switched off the
corresponding function.

41

1

Instruments

308_en_Chap01_instruments-de-bord_ed01-2016

use this button to go to the
secondary page.

use this button to return to the
primary page.

use this button for access to
additional information and to the
settings for certain functions.

use this button to confirm.

use this button to quit.

Principles

use the buttons on either side of the touch
screen for access to the menus, then press the
virtual buttons in the touch screen.
each menu is displayed over one or two pages
(primary page and secondary page).

After a few moments with no action on
the secondary page, the primary page
is displayed automatically.

Air conditioning.
Allows adjustment of the various
settings for temperature, air flow...
See the sections on "Heating",
"Manual air conditioning" and "Digital
air conditioning".

Touch screen menus

Driving assistance.
Allows certain functions to be switched
on and off and their settings adjusted.

Telephone.
See the "Audio equipment and telematics" section.

Media.
See the "Audio equipment and telematics" section.

Navigation.
Depending on trim level, navigation can
be not available, an option or standard.
See the "Audio equipment and
telematics" section.

Configuration.
Allows configuration of the display
and the system.

Connected services.
these services can be not available, an option or
standard.
See the "Audio equipment and telematics" section.

1. Volume / mute.
See the "Audio equipment and telematics" section.

42

Instruments

"Driving assistance" menu

the systems with settings that can be adjusted are detailed in the table below.

Button

Corresponding function

Comments

Speed settings

Memorisation of speeds for use with the speed limiter or cruise control.

Under-inflation initialisation

Reinitialisation of the under-inflation system.

Blind spot sensors

Activation of the function.

Park Assist

Activation/Deactivation of the function

43

1

Instruments

308_en_Chap01_instruments-de-bord_ed01-2016

Button

Corresponding function

Comments

Vehicle settings

Access to other functions with settings that can be adjusted.
Select or deselect the tabs at the bottom of the screen to display the functions required.
- "Driving assistance"

- "[Automatic rear wiper in reverse]" (activation of rear wiper coupled to reverse gear).

For more information on the Wiper control stalk, refer to the corresponding section.

- "[Collision risk alert]" (activation of the collision risk alert system).

For more information on Collision risk alert and emergency automatic braking, refer to the
corresponding section.
- "Lighting"

- "[guide-me-home lighting]" (automatic guide-me-home lighting),
- "[Welcome lighting]" (exterior welcome lighting).

For more information on the Lighting control stalk, refer to the corresponding section.

- "[Mood lighting]" (interior mood lighting).

For more information on Mood lighting, refer to the corresponding section.
- "Vehicle access"

- "[Driver plip action]" (selective unlocking of the driver's door).

For more information on the Remote control or Keyless Entry and Starting, refer to the
corresponding section.

- "[unlocking boot]" (selective unlocking of the boot).

For more information on the Boot, refer to the corresponding section.

Diagnostic

List of current alerts.

Parking sensors

Activation/Deactivation of the function.

Dynamic cruise control

Choice of the standard cruise control or the dynamic cruise control.
the choice of dynamic cruise control is retained on condition that the steering mounted control
thumbwheel is at the "CRuISe" position.

44

Instruments

State of adjustable systems

Operating fault
In the event of a fault with one of these
systems, the indicator lamp in the activation/
deactivation button flashes for a few moments.
An alert symbol is displayed to the right of the
button symbol, then, in the case of systems that
are activated by default, the orange indicator
comes on permanently.
every time the button is pressed, the indicator
flashes for a few moments.

example:

Some systems have a dedicated button, to
which is associated an indicator lamp.
Illumination of this lamp indicates whether the
system is activated or deactivated compared to
the default (factory) setting.
green indicator: you have switched on the
corresponding system.
Orange indicator: you have switched off the
corresponding system.

● Function not activated.

● Operating fault alert.

then

45

1

Instruments

308_en_Chap01_instruments-de-bord_ed01-2016

the functions available through this menu are detailed in the table below.

"Configuration" menu

Button

Corresponding function

Comments

Audio settings

Adjustment of volume, balance...

Colour schemes

Choice of colour scheme.

Interactive help

Access to the interactive user guide.

Turn off screen

Brightness

46

Instruments

Button

Corresponding function

Comments

System Settings

Choice of units:
-

temperature (°Celsius or °Fahrenheit)

-

distance and fuel consumption (l/100 km, mpg or km/l).

Time/Date

Setting the date and time.

Languages

Choice of language used: French, english, Italian, Spanish, german, Dutch, Portuguese,
Polish, turkish, Russian, Serbian, Croat, Hungarian, Czech, Brazilian.

Screen settings

Adjustment of the display settings (scrolling of text, animations...)

Calculator

Calendar