Peugeot 1007 (2008 year). Manual — part 4
3
52
4 - Access to the rear seats
If necessary, detach the seat belt
from the handle and position it along
the door pillar.
Lift the control A with one hand
and guide the movement of the
seat
forwards
with
your
other
hand (keeping the control in the
raised position).
The driver has a courtesy handle
B , located on the inner side of the
passenger seat, to enable him to tilt
the seat to allow a child into the rear,
for example.
When it is put back in place, the seat
returns to its initial position.
5 - Head restraint height and
angle adjustment
To raise the head restraint, pull it
upwards.
To lower it, it is necessary to push
simultaneously:
-
the button, located on the left
guide at the base of the head
restraint frame,
-
the head restraint downwards.
No person or object should
prevent the seat from return-
ing to its initial position; the
return to this position is nec-
essary in order for it to be
secured.
The head restraint is fi tted with a
frame which has notches which
prevent it from lowering; this is an
impact safety device.
Never drive with the head
restraints removed; they must
be in place and correctly
adjusted.
The adjustment is correct
when the upper edge of
the head restraint is level
with the top of the head.
To adjust the angle of the head
restraint, tilt it.
To remove it, press the lug and pull
it upwards.
3
53
6 - Storage drawer
Your vehicle has a storage drawer
under each seat.
To open it, lift it and pull.
To remove it, bring it to the end of its
travel, press the ends of the slides
and lift it, then pull it fully.
To put it back in place, at the end
of its travel, press on the top of the
drawer to secure it.
7 - Placing the passenger seat in
the table position
Use one of the two red controls at the
base, on each side of the seat.
To place the seat in the table position,
lift this control with one hand and
guide the seat back to the table
position with your other hand.
To return the seat to its upright
position,
carry
out
exactly
the
same operations in reverse order
(always raise the red control).
As a safety precaution, a
passenger sitting in the rear
of the vehicle must not place
his feet on the front seat
when placed in the table
position.
Do not place objects weigh-
ing more than 1 kg in the
drawers.
3
54
REAR SEATS
Seat back angle adjustment
Tilt the control C and adjust the angle
to the comfort or loading position.
Release the control to lock.
Folding/Placing in the
"fully folded" position
Place the head restraint in the low
position.
Position the seat belt buckle as close
as possible to the strap return.
Move the seat as far back as
possible using the bar A or the
handle B .
Fold the seat back onto the seat
cushion tilting control C fully.
Note: you can lock the seat back in
this position by pressing on it.
Push the control D upwards to
release the rear feet.
Place the seat in the "fully folded"
position.
When driving, the seat is retained in
this position by the side strut.
Table position
Place the head restraint in the low
position.
Fold the seat back onto the seat
cushion tilting control C fully.
Note: you can lock the seat back in
this position by pressing on it.
Forwards-backwards adjustment
Lift the bar A and slide the seat
forwards or backwards.
From the boot, you can press the red
handle B and slide the seat forwards
or backwards.
This manoeuvre makes folding of the
seat when loading the boot easier.
3
55
Never drive with the head
restraints
removed,
they
must be in place and correctly
adjusted.
Locked
Released
In order to ensure that the
seat covers have a long
service life, do not leave
the seat in the table or "fully
folded" position after loading.
Avoid placing luggage on the seats
when they are in the table position.
REAR HEAD RESTRAINTS
The rear head restraints can be
removed and have two positions;
-
high, position for use
-
low, storage position
Repositioning the seat
Press the control D upwards to check
that the rear feet are released.
Tilt the folded seat rearwards.
The rear feet are secured automatically.
Check that the seat is secured
correctly.
Raise the seat back, releasing it fi rst
by pulling the control C .
To raise a head restraint, pull it
upwards.
To lower it, press the lug then the
head restraint.
To remove it, place it in the high
position, push the lug and pull it
upwards.
To refi t it, engage the head restraint
rods in the holes taking care to remain
in the centreline of the seat back.
3
56
SEAT MODULARITY AND
THE VARIOUS SEAT
CONFIGURATIONS
The design of your vehicle and of its
seats offers several confi gurations.
Examples of various arrangements
combining convenience and con-
viviality:
It is imperative that the
various
operations
which
lead to modifi cation of the
existing confi guration are
carried out when stationary.
3
57
3
58
Although one of PEUGEOT’s main
criteria when designing your vehicle,
the safety of your children also
depends on you.
INSTALLING A CHILD SEAT
USING A THREE POINT SEAT
BELT
Intermediate longitudinal
position
*
The rules for transporting chil-
dren are specifi c to each country.
Consult the current legislation in
your country.
GENERAL POINTS RELATING
TO CHILD SEATS
"Forwards-facing"
When a "forwards-facing" child seat
is installed on the front passenger
seat , adjust the vehicle’s seat to the
intermediate
longitudinal
position
with the seat back upright and leave
the passenger air bag armed.
"Rearwards-facing"
When a "rearwards-facing"
child seat is installed on the
front passenger seat , it is
essential that the passenger
air bag is disarmed. Otherwise, the
child would risk being seriously
injured or killed if the air bag were
to infl ate.
For maximum safety, please
follow these precautions:
-
in accordance with Directive
2003/20, all children under
the age of 12 or less than one
metre fi fty tall must travel in
approved child seats suited
to their weight
, on seats fi tted
with a seat belt or ISOFIX
mountings * ,
-
statistically, the safest seats
in your vehicle for the trans-
portation of children are the
rear seats,
-
a child weighing less than 9 kg
must travel in the "rearwards-
facing" position both in the
front and in the rear.
PEUGEOT recommends that chil-
dren should travel in the rear seats
of your vehicle:
-
"rearwards-facing" up to the
age of 2,
-
"forwards-facing" over the age
of 2.
3
61
ADVICE ON CHILD
SEATS
Installing a booster seat
The chest part of the seat belt must
be positioned on the child’s shoulder
without touching the neck.
Ensure that the lap part of the seat
belt passes correctly over the child’s
thighs.
PEUGEOT recommends the use of
a booster seat which has a back,
fi tted with a seat belt guide at
shoulder level.
As a safety precaution, do not leave:
-
one or more children alone and
unsupervised in a vehicle,
-
a child or an animal in a vehicle
which is exposed to the sun,
with the windows closed,
-
the keys within reach of children
inside the vehicle.
To protect young children from the
rays of the sun, fi t side blinds on the
rear windows.
Children under the age of 10 must not
travel in the "forward facing" position
on the front passenger seat, unless
the rear seats are already occupied
by other children, cannot be used or
are absent.
Disarm the passenger air bag when
a "rear facing" child seat is installed
on the front seat.
Otherwise, the child would risk being
seriously injured or killed if the air
bag were to infl ate.
The incorrect installation of a child
seat in a vehicle compromises the
child’s protection in the event of an
accident.
Remember to fasten the seat belts or
the child seat harness keeping the
slack in relation to the child’s body to
a minimum , even for short journeys.
For optimum installation of the
"forward facing" child seat, ensure
that the back of the child seat is in
contact with the back of the vehicle’s
seat and that the head restraint does
not cause any discomfort.
If the head restraint has to be
removed, ensure that it is stored or
attached securely to prevent it from
being thrown around the vehicle in
the event of sharp braking.
3
59
CHILD SEATS RECOMMENDED BY PEUGEOT
PEUGEOT offers a complete range of recommended child seats which are
secured using a three point seat belt :
Passenger air bag OFF
Group 0: from birth to 10 kg
Group 0+: from birth to 13 kg
L1
"ROMER Baby-Safe Plus"
Installed in the rear-facing position
Groups 1, 2 and 3: from 9 to 36 kg
L2
"KIDDY Life"
For the safety of young children
(from 9 to 18 kg), PEUGEOT
recommends use of the restraining
cushion.
Groups 2 and 3: from 15 to 36 kg
L3
"RECARO Start"
L4
"KLIPPAN Optima"
From the age
of 6 years
(approximately 22 kg),
the booster is used on
its own.
3
60
INSTALLING CHILD SEATS SECURED USING THE SEAT BELT
In accordance with European regulations, this table indicates the options for the installation of child seats secured using the
seat belt and universally approved in accordance with the weight of the child and the seat in the vehicle.
U : seat suitable for the installation of a child seat secured using the seat belt and universally approved "rear facing" and/or
"forward facing".
Child seats fi tted with a support which rests on the fl oor of the vehicle must not be installed in the rear.
Weight of the child/indicative age
Seat
Below 13 kg
(groups 0 ( a ) and 0+)
Up to 1 year approx
From 9 to 18 kg
(group 1)
From 1 to 3 years approx
From 15 to 25 kg
(group 2)
From 3 to 6 years approx
From 22 to 36 kg
(group 3)
From 6 to 10 years approx
Front passenger
seat (b)
U
U
U (c)
U (c)
Rear seat
U (d)
U
U (c)
U (c)
(a) Group 0: from birth to 10 kg.
(b) Consult the legislation in force in your country before installing your child on this seat.
(c) Vehicle seat in the intermediate longitudinal position.
(d) Vehicle seat in the most rearward position.
3
62
"ISOFIX" MOUNTINGS
Your vehicle has been approved in
accordance with the new ISOFIX
regulation .
The
seats * ,
represented
below,
are fi tted with regulation ISOFIX
mountings:
These are three rings for each seat:
This
ISOFIX
mounting
system
guarantees you fast, reliable and
safe fi tting of the child seat in your
vehicle.
The ISOFIX child seats
are fi tted
with two locks which are secured
easily on these lower rings A .
Some also have an upper strap
which is attached to the upper ring B .
-
two lower rings A , located
between the vehicle seat back
and
cushion,
indicated
by
a label,
-
an upper ring B , referred to as
the TOP TETHER , indicated by
a label.
To attach this strap, raise the
vehicle seat’s head restraint
then pass the hook between
its rods. Then fi x the hook
on the upper ring B and tighten the
upper strap.
The incorrect installation of a
child seat in a vehicle compro-
mises the child’s protection in
the event of an accident.
For information regarding the ISOFIX
child seats which can be installed in
your vehicle, consult the summary
table for the location of the ISOFIX
child seats.
Child seats fi tted with a support which
rests on the fl oor of the vehicle must
not be installed in the rear
*
According to version.
3
63
This child seat can also be used on seats which are not fi tted with ISOFIX mountings.
In this case, it must be attached to the vehicle seat using the three point seat belt.
Follow the instructions for fi tting the child seat given in the seat manufacturer’s installation guide.
ISOFIX RÖMER Duo Plus (size category B1 )
Group 1: from 9 to 18 kg
Installed in the forward facing position.
Fitted with an upper strap to be secured on the ISOFIX upper ring,
referred to as the TOP TETHER.
Three seat body angles: sitting, reclining, lying.
ISOFIX CHILD SEAT RECOMMENDED BY PEUGEOT AND APPROVED FOR YOUR VEHICLE
3
64
SUMMARY TABLE FOR THE INSTALLATION OF ISOFIX CHILD SEATS
In accordance with European regulations, this table indicates the options for the installation of ISOFIX child seats on the
vehicle seats fi tted with ISOFIX mountings.
In the case of the universal and semi-universal ISOFIX child seats, the child seat’s ISOFIX size category, determined by a
letter from A to G , is indicated on the child seat next to the ISOFIX logo.
IUF: seat suitable for the installation
of an I
sofi x U niversal seat,
" F orward facing" and secured
using the "Top Tether" upper
strap.
*
The ISOFIX infant car seat is
fi xed to the lower rings of an
ISOFIX seat and occupies the
two rear seats.
IL-SU: seat suitable for the installation
an I
sofi x S emi- U niversal seat
which is:
-
"rear facing" fi tted with a "Top
Tether" upper strap,
-
an infant car seat which is secured
using the "Top Tether" upper strap.
Child seats fi tted with a support which rests on the fl oor of the vehicle must not be installed on the rear seats.
Weight of the child /indicative age
Less than 10 kg
(group 0)
Up to approx.
6 months
Less than 10 kg
(group 0)
Less than 13 kg
(group 0+)
Up to approx. 1 year
From 9 to 18 kg
(group 1)
From 1 to 3 years approx
Type of ISOFIX child seat
Infant car seat *
"rear facing"
"rear facing"
"forward facing"
ISOFIX size category
F
G
C
D
E
C
D
A
B
B1
Universal and semi-universal
ISOFIX child seats
which can be installed on the
rear seats
IL-SU
IL-SU
IL-SU
IUF
IL-SU
For the securing of the "Top Tether"
upper strap, refer to the "Isofi x Mountings"
section.
3
65
"CAMELEO" INTERIOR
The Cameleo concept is based
on a range of very different kits
which enable you to transform the
passenger compartment into one
which is unique and attractive.
They consist of the following 18 items:
-
two coverings 1 on the fascia,
-
four trims 2 for the side and centre
vents,
-
two trims 3 for the door panels,
-
four trims 4 for the seat cushions,
-
four trims 5 for the seat backs,
-
two trims 6 for the rear side
storage compartment covers.
For safety reasons, you must
not drive until you have installed
a kit completely.
Kits consisting of four vent trims are
also available.
The removal and fi tting of the items
in this kit does not require any tools.
3
66
1 - Fascia coverings
Removal
Pull one of the four corners of
the old fascia covering to detach
the velcro.
Fitting
Position the new covering fl at on
the fascia.
Press on the four corners to
attach the velcro securely.
2 - Vent trims
Removal
Turn an eighth of a turn to remove
the old trim.
Fitting
Position the new trim on the
vent.
Turn an eighth of a turn to the
notch to fi x the new trim.
3 - Door panel trims
Removal
Pull at the two notches to unclip
it fully.
Remove the old trim.
Fitting
Position the new trim on the door
starting at the top.
Press on the edges to clip it
securely.
3
67
4 - Seat cushion trims
Fitting
Position the new trim on the seat
cushion or on the seat back.
Engage the zip pull, located at
the base of the seat cushion or
seat back.
Guide the zip pull along the three
sides of the seat cushion or seat
back.
Position the velcro on the last
side of the seat cushion or seat
back trim.
On the rear seats, take care to
position the velcro correctly so
that the ISOFIX mountings are not
covered.
Fold down the zip pull tab in
the seat cushion or seat back
location.
6 - Rear side storage
compartment cover trims
Removal
Remove the tab from the zip pull,
located at the base of the seat
cushion or seat back.
Guide the zip pull along the three
sides of the seat cushion or seat
back.
Remove the zip pull.
Pull on the last side to detach the
velcro, then remove the old seat
cushion or seat back trim.
Removal
Open the cover to 45°.
Unclip the lug located under the
cover.
Remove the old cover trim.
Refi tting
Open the cover to 45°.
Position the new trim on the cover
by means of the two notches.
Tilt the trim on the cover.
Clip the lug located under the
cover.
Some Cameleo seat trims
can be dry cleaned. Please
ask a PEUGEOT dealer for
details.
5 - Seat back trims
Follow these instructions starting,
for each seat, with the complete
seat cushion removal and fi tting
operations, then repeat them for the
seat back.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст