Mitsubishi Outlander PHEV (2019 year). Manual — part 10
NOTE
l
Depending on the state of the vehicle (such
as during heating of the air conditioner), the
engine may start even if the needle of the en-
ergy usage indicator is indicated before zone
2 (the zone that the engine starts in high pos-
sibility).
l
Even when the EV priority mode is selected
and the engine does not start, the needle of
the energy usage indicator may indicate zone
2 (the zone that the engine starts in high pos-
sibility).
l
When the EV priority mode is selected, even
if the needle of the energy usage indicator
enters zone 2, it will not start the engine un-
less it is over the specified point by pressing
the accelerator pedal.
l
Depending on the vehicle condition, the
movement of the needle of the energy usage
indicator may be different or fluctuate.
l
Economical driving can be achieved by op-
erating in such state that the swing of the
needle is small within zone 1.
Charge zone
Indicates the charging power generated by
the regenerative brake.
The more the needle moves, the more electric
energy is charged.
The needle of the energy usage indicator may
not enter the charge zone when the drive bat-
tery is close to full charge.
Also, if the needle of the energy usage indi-
cator indicates the engine output zone, the
needle does not indicate the charge zone even
when there is charging of the electrical ener-
gy by regenerative braking.
NOTE
l
With the charging power gauge of the multi
information display, you can check the
charging power of electric energy generated
by regenerative braking even while the en-
gine is operating.
l
Both the display of the charge zone by the
energy usage indicator needle and the dis-
play of the charging power gauge in the mul-
ti information display indicate the charging
power of electric energy by regenerative
braking.
Engine output zone
Indicates the instantaneous output (kW) of
the engine.
Meter illumination control
E00531301174
Each time you press the rheostat illumination
button, there is a sound and the brightness of
the instruments changes.
1- Brightness level
2- Rheostat illumination button
NOTE
l
You can adjust to 8 different levels respec-
tively for when the position lamps are illu-
minated and when they are not.
l
When the lamp switch is in a position other
than the “OFF” position, the meter illumina-
tion switches automatically to the adjusted
brightness, depending on the brightness out-
side the vehicle.
Instruments
6-03
OGGE19E1
Instruments and controls
6
NOTE
l
The brightness level of the instruments is
stored when the operation mode of the pow-
er switch is put in OFF.
l
If you press and hold the button for about 2
seconds or more when the position lamps are
illuminated, the brightness level changes to
the maximum level. Pressing and holding
the button for about 2 seconds or more again
returns the brightness level to the previous
level.
On
vehicles
equipped
with
the
MITSUBISHI Multi-Communication Sys-
tem (MMCS), the map screen colour of
MITSUBISHI Multi-Communication Sys-
tem (MMCS) may not be switched to night-
time setting when the meter illumination
brightness level is at the maximum.
Multi information display
E00519903158
Always stop the vehicle in a safe place before
operating.
The following information is included on the
multi information display: warnings, odome-
ter, tripmeter, average fuel consumption, EV
cruising range, total cruising range, EVHV
driving rate, energy flow, etc.
[When the operation mode of the power
switch is OFF]
3- Drive battery level display screen
4- Odometer
5- “ ” or “ ” mark indicator
Multi information display
6-04
OGGE19E1
Instruments and controls
6
6- Door ajar warning display screen
NOTE
l
The drive battery level display screen ap-
pears when any of the doors or the tailgate is
opened during charging.
[When the operation mode of the power
switch is ON]
1- NORMAL mode indicator display
2- SNOW mode indicator display
3- LOCK mode indicator display
S-AWC (Super All Wheel Control)
4- ECO mode indicator display
5- SPORT mode indicator display
6- Battery charge mode display screen
7- Battery save mode display screen
8- EV priority mode display screen
10- Forward Collision Mitigation System
Ultrasonic misacceleration Mitigation
System (UMS) OFF display screen*
11- Lane Departure Warning (LDW) display
12- Cruise
Multi information display
6-05
OGGE19E1
Instruments and controls
6
13- Adaptive Cruise Control System (ACC)
14- Speed
15- Drive battery level display screen
16- Odometer
17- “ ” or “ ” mark indicator
20- Fuel
21- Outside temperature display screen
Multi information display
switch
E00520001911
Each time the multi information display
switch is operated, the buzzer sounds and the
multi information display changes between
information such as warnings, tripmeter,
average fuel consumption, EV cruising range,
total cruising range, EVHV driving rate, en-
ergy flow, etc.
It is also possible to change elements such as
the language and units used on the multi in-
formation display by operating the multi in-
formation display switch.
Multi information display
6-06
OGGE19E1
Instruments and controls
6
Information screen (when the operation mode is OFF)
E00520201968
Each time you lightly press the multi information display switch, the display screen switches in the following order.
*2
*1
*
1
: When there is no warning display
*
2
: When there is a warning display
1- Tripmeter ® p. 6-13
2- Tripmeter ® p. 6-13
6- Redisplay of a warning display screen
Multi information display
6-07
OGGE19E1
Instruments and controls
6
Information screen (when the operation mode is changed from OFF to ON)
E00520702351
When the operation mode is put in ON, the display screen switches in the following order.
*
1
: When the inspection time has arrived
1- Screen when the operation mode is OFF
2- System check screen
3- Screen when the operation mode is ON
4- Service reminder
Multi information display
6-08
OGGE19E1
Instruments and controls
6
Information screen (when the operation mode is ON)
E00521102192
Each time you lightly press the multi information display switch, the display screen switches in the following order.
or
*
1
: When the vehicle is charged
*
2
: When there is no warning display
*
3
: When there is a warning display
1- Tripmeter ® p. 6-13
2- Tripmeter ® p. 6-13
3- EV cruising range display/Total cruising
4- Average fuel consumption display
® p. 6-16
EVHV driving rate display
or
Energy flow display during charging
7- S-AWC (Super-All Wheel Control) op-
10- Redisplay of a warning display screen
Multi information display
6-09
OGGE19E1
Instruments and controls
6
NOTE
l
While driving, the service reminder is not displayed even if you operate the multi information display switch. Always stop the vehicle in a safe place before
operating.
l
While driving, the function setting screen is not displayed even if you operate the multi information display switch.
Before operation, park the vehicle in a safe place, firmly apply the parking brake, press the electrical parking switch, and shift to “P” (PARK) position.
Refer to “Changing the function settings” on page 6-17.
l
When there is information to be announced, such as a system fault, the buzzer sounds and the screen display is switched.
Refer to “Interrupt display screen” on page 6-10.
Interrupt display screen
E00522002084
Warning display
When there is information to be announced,
such as a system fault, the buzzer sounds and
the information screen is switched to the
warning display screen.
Refer to the warning list and take the neces-
sary measures.
Refer to “Warning display list” on page
6-26.
When the cause of the warning display is
eliminated, the warning display goes out au-
tomatically.
To return to the screen dis-
played before the warning dis-
play
Even if the cause of the warning display is
not eliminated, you can return to the screen
that was displayed before the warning dis-
play.
If you press the multi information display
switch, the display screen switches to the
screen that was displayed before the warning
display and the mark (A) is displayed.
If you want to switch the dis-
play
Warning display screens with a “ ” or “ ”
mark displayed in the upper right of the
screen can be switched. If you want to switch
the display, press the multi information dis-
play switch as follows.
“ ”: Press lightly.
“ ”: Press for approximately 2 seconds or
more.
Redisplay of a warning display
screen
When the mark is displayed, if you lightly
press the multi information display switch a
few times, the warning display screen you
switched from is redisplayed.
Other interrupt displays
The operation status of each system is dis-
played on the information screen.
Multi information display
6-10
OGGE19E1
Instruments and controls
6
Refer to the appropriate page in the warning
display list for further details.
Refer to “Other interrupt displays” on page
6-48.
mark display screen
E00533901028
This is displayed when you press the multi
information display switch and return from
the warning display screen to the previous
screen.
This mark is also displayed if there is another
warning other than the one displayed.
When the cause of the warning display is
eliminated, the mark goes out automatical-
ly.
NOTE
l
When the mark is displayed, the warning
display screen can be redisplayed on the in-
formation screen.
Refer to “Information screen (when the op-
eration mode is OFF)” on page 6-07.
Refer to “Information screen (when the op-
eration mode is ON)” on page 6-09.
Door ajar warning display
screen
E00522601979
If any of the doors or the tailgate is not com-
pletely closed, this displays the open door or
tailgate.
When the operation mode of the power
switch is ON, if the vehicle speed exceeds
approximately 8 km/h (5 mph) while a door
is ajar, a buzzer sounds 4 times. This notifies
the driver that a door is ajar.
CAUTION
l
Before moving your vehicle, check that the
warning display does not appear.
Drive battery level display
screen
E00537700027
Indicates the remaining pow-
er in the drive battery.
Fuel remaining display screen
E00522201542
This displays the amount of fuel remaining.
F- Full
E- Empty
Multi information display
6-11
OGGE19E1
Instruments and controls
6
NOTE
l
It may take several seconds to stabilise the
display after refilling the tank.
l
If fuel is added with the operation mode of
the power switch is in ON, the fuel gauge
may incorrectly indicate the fuel level.
l
The arrow (A) indicates that the fuel tank
filler is located on the left side of the body.
Fuel remaining warning display
E00522402495
When the fuel is reduced to approximately 7
litres, the information screen switches to the
interrupt display of the fuel remaining warn-
ing display, and the “ ” mark (B) on the fuel
remaining display flashes slowly (approxi-
mately once per second). After a few sec-
onds, the information screen returns from the
fuel remaining warning display to the previ-
ous screen.
If the remaining fuel level is reduced further,
the information screen switches to the fuel re-
maining warning display and the “ ” mark
(B) on the fuel remaining display flashes
quickly (approximately twice per second).
CAUTION
l
If the warning display appears, refuel as
soon as possible.
If the vehicle runs out of fuel, the engine
will not start even in a situation need to be
generated electricity, the following condi-
tions will occur.
•
The driving performance falls (since only
the electrical power stored in the drive
battery can be used for the driving).
•
The heating performance cannot be avail-
able (except for vehicles with an electric
heater).
•
The effectiveness of the heater is insuffi-
cient (vehicles with electric heater).
CAUTION
•
The catalytic converter may be damaged
due to excessive high temperature.
NOTE
l
On inclines or curves, the display may be in-
correct due to the movement of fuel in the
tank.
l
The battery save mode or battery charge
mode are cancelled or may not be activated
even if the battery save mode switch or the
battery charge mode is selected, depending
on the remaining quantity of the drive bat-
tery or the control condition of the system.
Charging power gauge
E00538400021
The charging power gauge shows momentary
charging power of the electric energy that is
generated by regenerative braking.
Charging power with regenerative brake
Low
High
Multi information display
6-12
OGGE19E1
Instruments and controls
6
NOTE
l
The charging power gauge does not include
the electric power generation by the engine
operation.
l
The charging power gauge does not indicate
the running condition of
bat-
tery charge.
l
The movement of the gauge decreases as the
drive battery level is nearly full.
Outside temperature display
screen
E00522101509
This shows the temperature
outside the vehicle.
NOTE
l
The display setting can be changed to the
preferred units (°C or °F).
Refer to “Changing the function settings” on
page 6-17.
l
Depending on factors such as the driving
conditions, the displayed temperature may
vary from the actual outside temperature.
Odometer
E00527800083
The odometer indicates the distance travel-
led.
Tripmeter
E00527901078
The tripmeter indicates the distance travelled
between two points.
Example usage of tripmeter
and tripmeter
It is possible to measure two currently
travelled distances, from home using
tripmeter
and from a particular point
on the way using tripmeter
.
To reset the tripmeter
To return the display to 0, hold down the
multi-information display switch for about 2
seconds or more. Only the currently dis-
played value will be reset.
Example
If tripmeter
is displayed, only tripmeter
will be reset.
NOTE
l
When disconnecting the auxiliary battery
terminal, the memory of tripmeter
and
are cleared, and the display returns to
“0”.
Service reminder
E00522502021
Displays the approximate time until the next
periodic
inspection
recommended
by
MITSUBISHI MOTORS. “---” is displayed
when the inspection time has arrived.
NOTE
l
Depending on the vehicle specifications, the
displayed time may differ from the next peri-
odic inspection time recommended by
MITSUBISHI MOTORS.
In addition, the display settings for the next
periodic inspection time can be modified.
To modify the display settings, have it adjus-
ted at a MITSUBISHI MOTORS Authorized
Service Point.
For more details, consult a MITSUBISHI
MOTORS Authorized Service Point.
1. Displays the time until the next periodic
inspection.
Multi information display
6-13
OGGE19E1
Instruments and controls
6
NOTE
l
The distance is shown in units of 100 km
(100 miles). The time is shown in units of
months.
2. This informs you that a periodic inspec-
tion is due. We recommend you to con-
sult a MITSUBISHI MOTORS Author-
ized Service Point.
At that time, when the ignition switch is
switched from “OFF” to “ON”, the
warning display is displayed for a few
seconds on the information screen.
3. After your vehicle is inspected at a
MITSUBISHI MOTORS Authorized
Service Point, it displays the time until
the next periodic inspection.
To reset
The “---” display can be reset while the igni-
tion switch or the opertion mode is in OFF.
When the display is reset, the time until the
next periodic inspection is displayed and the
warning display is no longer displayed when
the ignition switch is switched from “OFF” to
“ON”.
1. When you lightly press the multi infor-
mation display switch a few times, the
information display switches to the serv-
ice reminder display screen.
2. Press and hold the multi information dis-
play switch for about 2 seconds or more
to display “ ” and make it flash. (If
there is no operation for about 10 sec-
onds with flashing, the display returns to
the previous screen.)
3. Lightly press the multi information dis-
play switch while the icon is flashing to
change the display from “---” to
“CLEAR”. After this, the time until the
next periodic inspection will be dis-
played.
CAUTION
l
The customer is responsible for making sure
that periodic inspection and maintenance are
performed.
Inspections and maintenance must be per-
formed to prevent accidents and malfunc-
tions.
NOTE
l
“---” display cannot be reset when the opera-
tion mode is in ON.
Multi information display
6-14
OGGE19E1
Instruments and controls
6
NOTE
l
When “---” is displayed, after a certain dis-
tance and a certain period of time, the dis-
play is reset and the time until the next peri-
odic inspection is displayed.
l
If you accidentally reset the display, we rec-
ommend you to consult a MITSUBISHI
MOTORS Authorized Service Point.
System check screen
E00531001070
When the operation mode is put in ON, the
system check screen is displayed for about 4
seconds. If there is no fault, the information
screen (when the operation mode is ON) is
displayed.
If there is a fault, the screen changes to warn-
ing display.
Refer to “Warning display list” on page
6-26.
NOTE
l
The system check screen display varies de-
pending on the customer’s equipment.
EV cruising range display/
Total cruising range display
E00537600042
This displays the approximate driving range
(how many more kilometres or miles you can
drive).
EV cruising range display (A)
This displays the distance that can be traveled
with the remaining power in the drive battery.
Total cruising range display (B)
This displays the distance that can be traveled
with the remaining power in the drive battery
and the remaining amount of fuel.
NOTE
l
The EV cruising range may vary depending
on the driving conditions and your personal
driving habits.
The EV cruising range is calculated from the
following information.
•
Current remaining power in the drive bat-
tery.
•
The most recent electric power consump-
tion rate.
NOTE
•
Operation status of the air-conditioner.
If the preceding driving condition is in the
following situations, the EV cruising
range display may show less distance than
before even though there is almost the
same level of remaining power in the
drive battery.
•
When much electricity is consumed from
the drive battery, such as in a traffic jam,
hill-climbing or high-speed driving.
•
When the air conditioner is operating.
Treat the distance displayed as just a rough
guideline.
In addition, disconnecting the auxiliary bat-
tery cable will reset the EV cruising range
and the EV cruising range display may show
a different distance from the previous dis-
tance.
l
The learned value for the EV cruising range
can be reset by operating the multi informa-
tion display switch.
If the EV cruising range display shows an
extremely different distance, please reset the
learned value to the initialized value.
For details, refer to “Reset of EV/Total
cruising range” on page 6-22.
l
When the drive battery is charged or the ve-
hicle is refuelled, the cruising range display
is updated. However, if the charge level is
low or the refueling amount is small, it can-
not be updated correctly. Fully charge the
battery or refill to full tank whenever possi-
ble.
Multi information display
6-15
OGGE19E1
Instruments and controls
6
NOTE
l
On rare occasions, the value displayed for
the driving range may change if you are
parked on an extremely steep incline. This is
due to the movement of fuel in the tank and
does not indicate a malfunction.
l
The display setting can be changed to the
preferred units (km or miles).
Refer to “Changing the function settings” on
page 6-17.
l
When the EV cruising range falls below ap-
proximately 1 km (1 mile), the EV cruising
range display shows “---”.
l
When the total cruising range falls below ap-
proximately 50 km (30 miles), the total
cruising range display shows “---”.
Average fuel consumption dis-
play
E00531201128
This displays the average fuel consumption
from the last reset to the present time.
There are the following 2 mode settings.
Refer to “Changing the reset mode for aver-
age fuel consumption” on page 6-18.
For information on how to change the aver-
age fuel consumption display setting, refer to
“Changing the function settings” on page
6-17.
NOTE
l
The average fuel consumption display can
be reset separately for the auto reset mode
and for the manual reset mode.
l
“---” is displayed when the average fuel con-
sumption cannot be measured.
l
The initial (default) setting is “Auto reset
mode”.
l
The average fuel consumption depends on
the driving condition (road condition, driv-
ing behavior, etc.). The displayed fuel con-
sumption may vary from the actual fuel con-
sumption. Treat the fuel consumption dis-
played as just a rough guideline.
l
The memory of the auto reset mode or man-
ual reset mode for the average fuel con-
sumption display is erased if the auxiliary
battery is disconnected.
l
The display setting can be changed to the
preferred units {km/L, mpg (US), mpg (UK)
or L/100 km}.
Refer to “Changing the function settings” on
page 6-17.
EVHV driving rate display
E00537500038
This displays the ratios of the time travelled
with electric power and the time travelled
with both electric power and engine power.
The ratio of the time traveled with electric
power is displayed with a bar graph (blue)
and in a percentage.
NOTE
l
When the drive battery is fully charged,
EVHV driving rate is reset and display be-
comes 100 %.
Energy flow display
E00537400040
This displays the flow of energy.
A- Engine
B- Drive battery
C- Tyre
Multi information display
6-16
OGGE19E1
Instruments and controls
6
Blue arrow-
Flow of electric en-
ergy
Amber arrow-
Flow of other energy
Display of energy flow (exam-
ple)
When driving with electric energy
When driving with fuel (petrol) energy
When driving with both electric energy
and fuel (petrol) energy
When charging the drive battery
When there is no energy flow
NOTE
l
During charging, the energy flow display for
charging is displayed. For details, refer to
“Energy flow display during charging” on
page 3-26.
ECO Score
E00531601207
ECO score indicates the points you have
scored on fuel-efficient driving by the num-
ber of leaves as follows:
[When the operation mode is ON]
The display shows the score you achieved in
the last several minutes.
[When the operation mode is put in OFF]
The display shows the overall ECO score the
function has counted from the time when the
operation mode is set to “ON” to the time
when it is set to “OFF”.
ECO drive level
Low
High
Changing the function settings
E00522702254
The “Display language”, “Temperature unit”,
“Fuel consumption unit”, and “Average fuel
consumption and speed reset method” etc.
setting can be modified as desired.
1. Stop the vehicle in a safe place.
Firmly apply the parking brake, and
press the electrical parking switch and
shift to “P” (PARK) position.
2. Lightly press the multi information dis-
play switch a few times to switch the in-
formation screen to the function setting
screen.
Multi information display
6-17
OGGE19E1
Instruments and controls
6
Refer to “Information screen” on page
6-09.
CAUTION
l
For safety, stop the vehicle before operating.
While driving, even if you operate the multi
information display switch, the function set-
ting screen is not displayed.
3. Press and hold the multi information dis-
play switch for about 2 seconds or more
to switch from the setting mode screen
to the menu screen.
NOTE
l
To return the menu screen to the function
setting screen, press and hold the multi in-
formation display switch for about 2 seconds
or more.
l
If no operations are made within about 30
seconds of the menu screen being displayed,
the display returns to the function setting
screen.
4. Select the item to change on the menu
screen and change to the desired setting.
Refer to the following items for further
details on the operation methods.
Refer to “Changing the reset mode for
average fuel consumption” on page
6-18.
Refer to “Changing the fuel consump-
tion display unit” on page 6-19.
Refer to “Changing the temperature
unit” on page 6-20.
Refer to “Changing the display lan-
guage” on page 6-20.
Refer to “Changing the language cooper-
ative control” on page 6-21.
Refer to “Operation sound setting” on
page 6-21.
Refer to “Changing the time until
“REST REMINDER” is displayed” on
page 6-22.
Refer to “Changing the turn-signal
sound” on page 6-22.
Refer to “Reset of low tyre pressure
warning threshold” on page 7-96.
Refer to “Tyre ID set change” on page
7-96.
Refer to “Reset of EV/Total cruising
range” on page 6-22
Refer to “Returning to the factory set-
tings” on page 6-22.
NOTE
l
If the auxiliary battery is disconnected, these
function settings are reset from memory and
return automatically to the factory settings
(except the low tyre pressure warning
threshold and tyre ID set).
Changing the reset mode for
average fuel consumption
E00522902243
The mode conditions for the average fuel
consumption display can be switched be-
tween “Auto reset” and “Manual reset”.
1. Press and hold the multi information dis-
play switch for about 2 seconds or more
to switch from the setting mode screen
to the menu screen.
Refer to “Changing the function set-
tings” on page 6-17.
Multi information display
6-18
OGGE19E1
Instruments and controls
6
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст