Mitsubishi ASX (2018 year). Manual — part 26
2. Turn the cap (B) anticlockwise to re-
move it.
*: Front of the vehicle
3. Turn the bulb (C) anticlockwise to re-
move it.
*: Front of the vehicle
4. While holding down the tab (D), pull out
the socket (E).
5. To install the bulb, perform the removal
steps in reverse.
CAUTION
l
Handle halogen lamp bulbs with care. The
gas inside halogen lamp bulbs is highly pres-
surized, so dropping, knocking, or scratching
a halogen lamp bulb can cause it to shatter.
l
Never hold the halogen lamp bulb with a
bare hand, dirty glove, etc.
The oil from your hand could cause the bulb
to break the next time the headlamps are op-
erated.
If the glass surface is dirty, it must be
cleaned with alcohol, paint thinner, etc., and
refit it after drying it thoroughly.
Position lamps (type 1)
E01003702619
1. When replacing the bulb on the left side
of the vehicle in the case of diesel-pow-
ered vehicles, remove the bolt (A) hold-
ing down the relay box and move the re-
lay box towards the rear of the vehicle.
*: Front of the vehicle
Replacement of lamp bulbs
10-30
OGAE18E1
Maintenance
10
2. When replacing the bulb on the right
side of the vehicle in the case of diesel-
powered vehicles, remove the clips (B)
by prying with a straight blade (or mi-
nus) screwdriver, and remove the side
cover.
*: Front of the vehicle
3. Turn the socket (C) anticlockwise to re-
move it.
*: Front of the vehicle
4. Pull the bulb out of the socket.
5. To install the bulb, perform the removal
steps in reverse.
Front turn-signal lamps
E01003800922
To remove
1. Remove the upper cover.
For information regarding how to re-
move the upper cover, refer to “Remov-
ing and installing the upper cover and
duct” on page 10-10.
2. Remove the entire socket and bulb as-
sembly (A) by turning it anticlockwise.
*: Front of the vehicle
3. Remove the bulb by pulling it out.
To install
1. To install the bulb, perform the removal
steps in reverse.
Replacement of lamp bulbs
10-31
OGAE18E1
Maintenance
10
2. Install the upper cover.
For information regarding how to install
the upper cover, refer to “Removing and
installing the upper cover and duct” on
page 10-10.
Side turn-signal lamps (on
fender)*
E01003900516
NOTE
l
For the side turn-signal lamps (on fender), it
is not possible to repair or replace just the
bulb.
Contact a MITSUBISHI MOTORS Author-
ized Service Point when there is a need for
repair or replacement.
Side turn-signal lamps (on out-
side rear-view mirror)*
E01003900529
NOTE
l
An LED, not a bulb, is used in the side turn-
signal lamps (on outside rear-view mirror).
Contact a MITSUBISHI MOTORS Author-
ized Service Point when there is a need for
repair or replacement.
Front fog lamps*
E01004003603
1. Remove the clip (A).
2. Insert a straight blade (or minus) screw-
driver with a cloth over its tip into the
fog lamp cover (B) and pry gently to re-
move it.
3. Remove the screws (C) and remove the
lamp unit.
NOTE
l
Except for vehicles equipped with daytime
running lamps, when unfastening the screws,
be careful not to move the beam position ad-
justment screw (D).
Replacement of lamp bulbs
10-32
OGAE18E1
Maintenance
10
4. While holding down the tab (E), pull out
the socket (F).
5. Turn the bulb (G) anticlockwise to re-
move it.
6. To install the bulb, perform the removal
steps in reverse.
CAUTION
l
Handle halogen lamp bulbs with care. The
gas inside a halogen lamp bulbs is highly
pressurized, so dropping, knocking, or
scratching a halogen lamp bulb can cause it
to shatter.
l
Never hold the halogen lamp bulb with a
bare hand, dirty glove, etc.
The oil from your hand could cause the bulb
to break the next time the fog lamps are op-
erated.
If the glass surface is dirty, it must be
cleaned with alcohol, paint thinner, etc., and
refit it after drying it thoroughly.
NOTE
l
When refitting the clip, first insert part (H)
of the clip into the hole and then press part
(I) into it.
Daytime running lamps* / Posi-
tion lamps (Type 2)*
E01012400096
NOTE
l
The daytime running lamps/position lamps
(Type 2) use an LED instead of a bulb.
Check with a MITSUBISHI MOTORS Au-
thorized Service Point when the lamp needs
to be repaired or replaced.
Replacement of lamp bulbs
10-33
OGAE18E1
Maintenance
10
Rear fog lamp
E01004101730
NOTE
l
The rear fog lamp uses an LED instead of a
bulb. Check with a MITSUBISHI MOTORS
Authorized Service Point when the lamp
needs to be repaired or replaced.
Rear combination lamps
E01004203009
1. Remove the screws (A) that hold the
lamp unit and remove the lamp unit.
2. Turn the socket and bulb assembly anti-
clockwise to remove it.
B- Stop and tail lamp (LED) - cannot be
replaced
C- Rear turn-signal lamps
NOTE
l
An LED, not a bulb, is used in the stop
lamp/tail lamp. Contact a MITSUBISHI
MOTORS Authorized Service Point when
there is a need for repair or replacement.
3. Pull the bulb out of the socket.
4. To install the bulb, perform the removal
steps in reverse.
NOTE
l
When mounting the lamp unit, align the
groove (D) on the lamp unit with the clip on
the body and the pin (E) on the unit with the
hole in the body.
Reversing lamps
E01004401430
1. Open the tailgate.
2. Insert a straight blade (or minus) screw-
driver into the notch of the cover and pry
gently to remove the cover.
Replacement of lamp bulbs
10-34
OGAE18E1
Maintenance
10
NOTE
l
Wrap a piece of cloth around the tip of the
screwdriver in order to avoid scratching the
cover.
3. Remove the socket and bulb assembly
by turning it anticlockwise.
4. Remove the bulb by pulling it out.
5. To install the bulb, perform the removal
steps in reverse.
NOTE
l
When installing the lid, align the tab on the
lid with the hole on the vehicle side.
Licence plate lamps
E01004602093
1. When removing the lamp unit (A), push
it towards the left side of the vehicle
body.
2. Remove the socket (B) and bulb assem-
bly by turning it anticlockwise.
Replacement of lamp bulbs
10-35
OGAE18E1
Maintenance
10
3. Remove the bulb by pulling it out.
4. To install the bulb, perform the removal
steps in reverse.
NOTE
l
When installing the lamp, insert tab (C) first
then align and insert tab (D).
High-mounted stop lamp
E01004500593
NOTE
l
An LED, not a bulb, is used in the high-
mounted stop lamp.
Contact a MITSUBISHI MOTORS Author-
ized Service Point when there is a need for
repair or replacement.
Replacement of lamp bulbs
10-36
OGAE18E1
Maintenance
10
Vehicle labeling. . . . . . . . . . . . . . . . . . . . 11-02
Vehicle dimensions. . . . . . . . . . . . . . . . . . ... 11-04
Vehicle performance. . . . . . . . . . . . . . . . . . . 11-06
Vehicle weight. . . . . . . . . . . . . . . . . . . . .. 11-07
Engine specifications. . . . . . . . . . . . . . . . . . 11-10
Electrical system. . . . . . . . . . . . . . . . . . . ... 11-11
Tyres and wheels. . . . . . . . . . . . . . . . . . . ...11-12
Fuel consumption. . . . . . . . . . . . . . . . . . . ..11-12
Refill capacities. . . . . . . . . . . . . . . . . . . . .11-15
Specifications
OGAE18E1
11
Vehicle labeling
E01100105207
Vehicle identification number
The vehicle identification number is stamped
on the bulkhead as shown in the illustration.
Vehicle information code plate
The vehicle information code plate is riveted
as shown in the illustration.
The plate shows model code, engine model,
transmission model and body colour code,
etc.
Please use this number when ordering re-
placement parts.
1- Model code
2- Engine model code
3- Transmission model code
4- Body colour code
5- Interior code
6- Option code
7- Exterior code
Vehicle labeling
11-02
OGAE18E1
Specifications
11
Vehicle identification number
plate (RHD vehicles only)
The vehicle identification number is stamped
on the plate riveted to the left front corner of
the vehicle body. It is visible from outside of
the vehicle through the windscreen.
Engine model/number
The engine model and number are stamped
on the engine cylinder block as shown in the
illustrations.
Petrol-powered vehicles
1600 models
*: Front of the vehicle
2000 models
*: Front of the vehicle
Diesel-powered vehicles
1600 models
*: Front of the vehicle
2200 models
*: Front of the vehicle
Vehicle labeling
11-03
OGAE18E1
Specifications
11
Vehicle dimensions
E01100204995
Except for vehicles equipped with wheel lip moldings
Vehicles equipped with wheel lip moldings
Vehicle dimensions
11-04
OGAE18E1
Specifications
11
Item
Vehicles for Russia, Kazakhstan,
Moldova and Ukraine
Except for vehicles for Russia,
Kazakhstan, Moldova and Uk-
raine
Vehicles with
16 or 17 inch
tyre
Vehicles with
18 inch tyre
Vehicles with
16 or 17 inch
tyre
Vehicles with
18 inch tyre
1
Front track
1,525 mm
1,540 mm
1,525 mm
1,545 mm
2
Overall width
Without wheel lip molding
—
—
1,770 mm
—
With wheel lip molding
1,810 mm
―
1,810 mm
3
Front overhang
930 mm
4
Wheel base
2,670 mm
5
Rear Overhang
765 mm
6
Overall length
4,365 mm
7
Ground clearance (unla-
den)
Petrol-powered vehicles
195 mm
215 mm
180 mm,
190 mm
*
190 mm
Diesel-powered vehicles
—
—
170 mm,
180 mm
*
180 mm
8
Overall height (unladen)
1,630 mm
1,645 mm
1,630 mm,
1,640 mm
*
1,640 mm
9
Rear track
1,530 mm
1,540 mm
1,530 mm
1,545 mm
Minimum turning radius
Body
5.7 m
Wheel
5.3 m
*
: 215/70R16 size tyre
Vehicle dimensions
11-05
OGAE18E1
Specifications
11
NOTE
l
The overall width varies depending on whether the vehicle is equipped with wheel lip moldings.
To determine whether your vehicle is equipped with wheel lip moldings, refer to “Exterior” on page 1-12.
Vehicle performance
E01100304228
Petrol-powered vehicles
Maximum speed
1600 models
183 km/h (114 mph)
2000 models
191 km/h (119 mph)
Diesel-powered vehicles
Maximum speed
1600 models
2WD
182 km/h (113 mph)
4WD
180 km/h (112 mph)
2200 models
190 km/h (118 mph)
Vehicle performance
11-06
OGAE18E1
Specifications
11
Vehicle weight
E01100408780
Petrol-powered vehicles
Item
1600 models
INFORM
INVITE
INTENSE
INSTYLE
Kerb weight
Without optional parts
1,260 kg
1,260 kg, 1,290 kg
*1
1,285 kg
With full optional parts
1,299 kg
1,299 kg, 1,306 kg
*1
1,355 kg
Maximum gross vehicle weight
1,870 kg, 1,825 kg
*2
Maximum axle weight
Front
930 kg
Rear
1,000 kg, 1,070 kg
*2
Maximum towable weight
With brake
1,200 kg
Without brake
665 kg, 670 kg
*1
Maximum trailer-nose weight
60 kg
Maximum roof load
80 kg
Seating capacity
5 persons
*1
: Vehicles for Russia, Kazakhstan, Moldova and Ukraine
*2
: In case of trailer towing
NOTE
l
Trailer specifications indicate the manufacturer’s recommendation.
Vehicle weight
11-07
OGAE18E1
Specifications
11
Item
2000 models
INVITE
INTENSE
Kerb weight
Without optional parts
1,440 kg
1,445 kg
With full optional parts
1,455 kg
1,512 kg
Maximum gross vehicle weight
1,970 kg, 2,035 kg
*
Maximum axle weight
Front
1,030 kg
Rear
1,000 kg, 1,085 kg
*
Maximum towable weight
With brake
1,300 kg
Without brake
745 kg
Maximum trailer-nose weight
65 kg
Maximum roof load
80 kg
Seating capacity
5 persons
*
: In case of trailer towing
NOTE
l
Trailer specifications indicate the manufacturer’s recommendation.
Vehicle weight
11-08
OGAE18E1
Specifications
11
Diesel-powered vehicles
Item
1600 models
2200 models
2WD
4WD
M/T
INFORM
INVITE
INTENSE
INSTYLE
INFORM
INVITE
INTENSE
INSTYLE
INFORM
INVITE
INTENSE
INSTYLE
Kerb weight
Without option-
al parts
1,355 kg
1,380 kg
1,420 kg
1,445 kg
1,520 kg
1,540 kg
With full option-
al parts
1,378 kg
1,442 kg
1,443 kg
1,507 kg
1,543 kg
1,602 kg
Maximum gross vehicle weight
1,980 kg, 2,050 kg
*
2,060 kg, 2,130 kg
*
Maximum axle
weight
Front
1,120 kg
Rear
1,000 kg, 1,090 kg
*
Maximum towa-
ble weight
With brake
1,400 kg
Without brake
695 kg
745 kg
750 kg
Maximum trailer-nose weight
70 kg
Maximum roof load
80 kg
Seating capacity
5 persons
*
: In case of trailer towing
NOTE
l
Trailer specifications indicate the manufacturer’s recommendation.
Vehicle weight
11-09
OGAE18E1
Specifications
11
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст