KIA Venga (2016 year). Manual — part 17
YN ENG 6.QXP
28.11.2016
16:06 Page 9
What to do in an emergency
WARNING - Changing a tire
•
To prevent vehicle movement
while changing a tire, always
set the parking brake fully,
and always block the wheel
diagonally opposite the wheel
being changed.
•
We recommend that the
wheels of the vehicle be
chocked, and that no person
OYN066019L
remain in a vehicle that is
OYN066027L
4. Remove the wheel lug nut wrench,
being jacked.
6. Loosen the wheel lug nuts coun-
jack, jack handle, and spare tire
terclockwise one turn each, but do
from the vehicle.
not remove any nut until the tire
has been raised off the ground.
5. Block both the front and rear of
wheel that is diagonally opposite
the jack position.
6 9
YN ENG 6.QXP
28.11.2016
16:06 Page 10
What to do in an emergency
WARNING - Jack location
To reduce the possibility of
injury, be sure to use only the
jack provided with the vehicle
and in the correct jack position;
never use any other part of the
vehicle for jack support.
OYN065022L
OYN066025L
8. Insert the jack handle into the jack
and turn it clockwise, raising the
vehicle until the tire just clears the
ground. This measurement is
approximately
30 mm (1.2 in).
Before removing the wheel lug
nuts, make sure the vehicle is sta-
ble and that there is no chance for
OYN065020L
movement or slippage.
7. Place the jack at the Front (1) or
rear (2) jacking position closest to
the tire you are changing. Place
the jack at the designated loca-
tions under the frame. The jacking
positions are plates welded to the
frame with two tabs and a raised
dot to index with the jack.
6 10
YN ENG 6.QXP
28.11.2016
16:06 Page 11
What to do in an emergency
9. Loosen the wheel nuts and
10. To reinstall the wheel, hold it on
remove them with your fingers.
WARNING
the studs, put the wheel nuts on
Slide the wheel off the studs and
Wheels and wheel covers may
the studs and tighten them finger
lay it flat so it cannot roll away. To
have sharp edges. Handle them
tight. Jiggle the tire to be sure it is
put the wheel on the hub, pick up
carefully to avoid possible
completely seated, then tighten
the spare tire, line up the holes
severe injury. Before putting the
the nuts as much as possible
with the studs and slide the wheel
wheel into place, be sure that
with your fingers again.
onto them. If this is difficult, tip the
there is nothing on the hub or
11. Lower the vehicle to the ground
wheel slightly and get the top hole
wheel (such as mud, tar, gravel,
by turning the wheel nut wrench
in the wheel lined up with the top
etc.) that interferes with the
counterclockwise.
stud. Then jiggle the wheel back
wheel from fitting solidly
and forth until the wheel can be
against the hub.
slid over the other studs.
If there is, remove it. If there is
not good contact on the mount-
ing surface between the wheel
and hub, the wheel nuts could
come loose and cause the loss
of a wheel. Loss of a wheel may
result in loss of control of the
vehicle. This may cause serious
injury or death.
6 11
YN ENG 6.QXP
28.11.2016
16:06 Page 12
What to do in an emergency
If you have a tire gauge, remove the
valve cap and check the air pressure.
CAUTION
If the pressure is lower than recom-
Your vehicle has metric threads
mended, drive slowly to the nearest
on the wheel studs and nuts.
service station and inflate to the cor-
Make certain during wheel
rect pressure. If it is too high, adjust
removal that the same nuts that
it until it is correct. Always reinstall
were removed are reinstalled -
the valve cap after checking or
or, if replaced, that nuts with
adjusting tire pressure. If the cap is
metric threads and the same
not replaced, air may leak from the
chamfer configuration are used.
tire. If you lose a valve cap, buy
Installation of a non-metric
another and install it as soon as pos-
thread nut on a metric stud or
OYN066028L
sible.
vice-versa will not secure the
Then position the wrench as shown
wheel to the hub properly and
After you have changed wheels,
in the drawing and tighten the wheel
will damage the stud so that it
always secure the flat tire in its place
nuts. Be sure the socket is seated
must be replaced.
and return the jack and tools to their
completely over the nut. Do not stand
proper storage locations.
Note that most lug nuts do not
on the wrench handle or use an
have metric threads. Be sure to
extension pipe over the wrench han-
use extreme care in checking
dle. Go around the wheel tightening
for thread style before installing
every other nut until they are all tight.
aftermarket lug nuts or wheels.
Then double-check each nut for
If in doubt, we recommend that
tightness. After changing wheels, we
you consult an authorized Kia
recommend that the system be
dealer.
checked by an authorized Kia dealer.
Wheel nut tightening torque:
Steel wheel & aluminum alloy wheel:
9~11 kgf·m (65~79 lbf·ft)
6 12
YN ENG 6.QXP
28.11.2016
16:06 Page 13
What to do in an emergency
Important - use of compact spare tire
WARNING - Wheel studs
(if equipped)
WARNING
If the studs are damaged, they
Your vehicle is equipped with a com-
The compact spare tire is for
may lose their ability to retain
pact spare tire. This compact spare
emergency use only. Do not
the wheel. This could lead to the
tire takes up less space than a regu-
operate your vehicle on this
loss of the wheel and a collision
lar-size tire. This tire is smaller than a
compact spare at the speed
resulting in serious injuries.
conventional tire and is designed for
over 80 km/h (50 mph). The
temporary use only.
original tire should be repaired
or replaced as soon as possible
To prevent the jack, jack handle,
to avoid failure of the spare
CAUTION
wheel lug nut wrench and spare tire
possibly leading to personal
from rattling while the vehicle is in
• You should drive carefully
injury or death.
motion, store them properly.
when the compact spare is in
use. The compact spare
should be replaced by the
The compact spare should be inflat-
WARNING - Inadequate
proper conventional tire and
ed to 420 kPa (60 psi).
spare tire pressure
rim at the first opportunity.
Check the inflation pressures
• The operation of this vehicle
as soon as possible after
is not recommended with
✽ NOTICE
installing the spare tire. Adjust
more than one compact spare
Check the inflation pressure after
it to the specified pressure, if
tire in use at the same time.
installing the spare tire. Adjust it to
necessary. Refer to “Tires and
the specified pressure, as necessary.
wheels” in section 8.
6 13
YN ENG 6.QXP
28.11.2016
16:06 Page 14
What to do in an emergency
When using a compact spare tire,
•
Do not take this vehicle through an
•
The compact spare tire should not
observe the following precautions:
automatic car wash while the com-
be used on any other wheels, nor
pact spare tire is installed.
should standard tires, snow tires,
•
Under no circumstances should
wheel covers or trim rings be used
you exceed 80 km/h (50 mph); a
•
Do not use tire chains on the com-
with the compact spare wheel. If
higher speed could damage the
pact spare tire. Because of the
such use is attempted, damage to
tire.
smaller size, a tire chain will not fit
these items or other car compo-
properly. This could damage the
•
Ensure that you drive slowly
nents may occur.
enough to avoid all hazards. Any
vehicle and result in loss of the
chain.
•
Do not use more than one compact
road hazard, such as a pothole or
debris, could seriously damage the
•
The compact spare tire should not
spare tire at a time.
compact spare.
be installed on the front axle if the
•
Do not tow a trailer while the com-
vehicle must be driven in snow or
pact spare tire is installed.
•
Any continuous road use of this tire
on ice.
could result in tire failure, loss of
vehicle control, and possible per-
•
Do not use the compact spare tire
sonal injury.
on any other vehicle because this
tire has been designed especially
•
Do not exceed the vehicle’s maxi-
for your vehicle.
mum load rating or the load-carry-
ing capacity shown on the sidewall
•
The compact spare tire’s tread life
of the compact spare tire.
is shorter than a regular tire.
Inspect your compact spare tire
•
Avoid driving over obstacles. The
compact spare tire diameter is
regularly and replace worn com-
pact spare tires with the same size
smaller than the diameter of a con-
ventional tire and reduces the
and design, mounted on the same
wheel.
ground clearance approximately
25 mm (1 inch), which could result
in damage to the vehicle.
6 14
YN ENG 6.QXP
28.11.2016
16:06 Page 15
What to do in an emergency
Jack label
1. Model Name
■ Example
2. Maximum allowable load
• Type A
3. When using the jack, set your
parking brake.
4. When using the jack, stop the
engine.
5. Do not get under a vehicle that is
supported by a jack.
OHYK064001
• Type B
6. The designated locations under
the frame
7. When supporting the vehicle, the
base plate of jack must be vertical
under the lifting point.
8. Shift into Reverse gear on vehicles
with manual transmission or move
OHYK064005
the shift lever to the P position on
• Type C
vehicles with automatic transmis-
sion.
9. The jack should be used on firm
level ground.
10. Jack manufacturer
11. Production date
OHYK064002
12. Representative company and
❈ The actual Jack label in the vehicle may differ from the illustration. For
address
more detailed specifications, refer to the label attached to the jack.
6 15
YN ENG 6.QXP
28.11.2016
16:06 Page 16
What to do in an emergency
EC Declaration of Conformity for Jack
JACKDOC14S
6 16
YN ENG 6.QXP
28.11.2016
16:06 Page 17
What to do in an emergency
IF YOU HAVE A FLAT TIRE (WITH TIREMOBILITYKIT, IF EQUIPPED)
Air pressure loss in the tire may
adversely affect tire performance.
For this reason, you should avoid
abrupt steering or other driving
maneuvers, especially if the vehicle is
heavily loaded or if a trailer is in use.
The TireMobilityKit is not designed or
intended as a permanent tire repair
method and is to be used for one tire
only.
This instruction shows you step by
OJC064010
OYN066026L
step how to temporarily seal the
puncture simply and reliably.
Please read the instructions before
Introduction
Read the section "Notes on the safe
using the TireMobilityKit.
With the TireMobilityKit you stay mobile
use of the TireMobilityKit".
(1) Compressor
even after experiencing a tire puncture.
(2) Sealant bottle
The system of compressor and seal-
WARNING
ing compound effectively and comfort-
ably seals most punctures in a pas-
Do not use the TireMobilityKit if
a tire is severely damaged by
senger car tire caused by nails or sim-
ilar objects and reinflates the tire.
driving run flat or with insuffi-
cient air pressure.
After you ensured that the tire is prop-
erly sealed you can drive cautiously
Only punctured areas located
on the tire (up to 200 km (120 miles))
within the tread region of the
at a max. speed of 80 km/h (50 mph)
tire can be sealed using the
in order to reach a vehicle or tire deal-
TireMobilityKit.
er to have the tire replaced.
Damage to the sidewall must
It is possible that some tires, especially
not be repaired due to safety rea-
with larger punctures or damage to the
sons.
sidewall, cannot be sealed completely.
6 17
YN ENG 6.QXP
28.11.2016
16:06 Page 18
What to do in an emergency
7. Pressure gauge for displaying the
tire inflation pressure
8. Button for reducing tire inflation
pressure
Connectors, cable and connection
hose are stored in the compressor
housing.
WARNING
Before using the TireMobilityKit,
follow the instructions on the
sealant bottle.
Remove the label with the speed
restriction from the sealant bottle
and apply it to the steering wheel.
Please note the expiry date on the
sealant bottle.
OGDE064102
Components of the TireMobilityKit
0. Speed restriction label
3. Connectors and cable for the
power outlet direct connection
1. Sealant bottle and label with
speed restriction
4. Holder for the sealant bottle
2. Filling hose from sealant bottle to
5. Compressor
wheel
6. On/off switch
6 18
YN ENG 6.QXP
28.11.2016
16:06 Page 19
What to do in an emergency
Using the TireMobilityKit
9) Switch off the compressor.
1. Filling the sealant
10) Detach the hose from the
Strictly follow the specified sequence,
sealant bottle connector and
otherwise the sealant may escape
from the tire valve.
under high pressure.
Return the TireMobilityKit to its stor-
1) Shake the sealant bottle.
age location in the vehicle.
WARNING
Carbon monoxide poisoning
and suffocation is possible if the
engine is left running in a poorly
OYN066026L
ventilated or unventilated loca-
6) Ensure that the compressor is
tion (such as inside a building).
switched off, position 0.
7) Connect between compressor
and the vehicle power outlet using
the cable and connectors.
OYN064021
✽ NOTICE
2) Connect the filling hose 2 onto the
Only use the front passenger side
connector of the sealant bottle (A).
power outlet.
3) Ensure that button 6 on the com-
pressor is not pressed.
8) With the ignition switched on:
4) Unscrew the valve cap from the
Switch on the compressor and let it
valve of the defective wheel and
run for approximately 3 minutes to fill
screw filling hose 2 of the sealant
the sealant. The inflation pressure of
bottle onto the valve.
the tire after filling is unimportant.
5) Insert the sealant bottle into the
housing of the compressor so that
the bottle is upright (B).
6 19
YN ENG 6.QXP
28.11.2016
16:06 Page 20
What to do in an emergency
Distributing the sealant
Producing the tire inflation pres-
- To reduce the inflation pres-
sure
sure: Press the button 8 on the
Immediately drive approximately 3 km
1) After driving approximately 3 km (2
compressor.
(2 miles) to evenly distribute the
sealant in the tire.
miles), stop at a suitable location.
2) Connect the filling hose 2 of the
CAUTION
compressor
(clip mounted side)
If the inflation pressure is not
CAUTION
directly and then connect the filling
maintained, drive the vehicle a
Do not exceed a speed of 80
hose 2 (opposite side) to the tire
second time, refer to Distributing
km/h (50 mph). If possible, do
valve.
the sealant. Then repeat steps 1
not fall below a speed of
20
to 4.
km/h (12 mph).
3) Connect between compressor and
the vehicle power outlet using the
Use of the TireMobilityKit may
While driving, if you experience
cable and connectors.
be ineffectual for tire damage
any unusual vibration, ride dis-
larger than approximately 4 mm
turbance or noise, reduce your
4) Adjust the tire inflation pressure to
(0.16 in).
speed and drive with caution
220 kPa (32 psi). With the ignition
until you can safely pull off of
switched on, proceed as follows.
We recommend that you contact
the side of the road.
the nearest Kia A/S center, or a
- To increase the inflation pres-
workshop that works according
Call for road side service or tow-
sure: Switch on the compressor,
to Kia repair procedures with
ing.
position I. To check the current
correspondingly trained per-
inflation pressure setting, briefly
sonnel if the tire cannot be
switch off the compressor.
made roadworthy with the
TireMobilityKit.
WARNING
Do not let the compressor run for
more than 10 minutes, otherwise
WARNING
the device will overheat and may
The tire inflation pressure must
be damaged.
be at least 200 kPa (29 psi). If it is
not, do not continue driving. Call
for road side service or towing.
6 20
YN ENG 6.QXP
28.11.2016
16:06 Page 21
What to do in an emergency
Notes on the safe use of the
•
Never leave the TireMobilityKit
Technical Data
TireMobilityKit
unattended while it is being used.
System voltage: DC 12 V
•
Park your car at the side of the
•
Do not leave the compressor run-
Working voltage: DC 10 - 15 V
road so that you can work with the
ning for more than 10 min. at a time
Amperage rating: max. 10A ± 1A
TireMobilityKit away from moving
or it may overheat.
(at DC 12V operation)
traffic. Place your warning triangle
•
Do not use the TireMobilityKit if the
Suitable for use at temperatures:
in a prominent place to make pass-
ambient temperature is below -30°C
-30 ~ +70°C (-22 ~ +158°F)
ing vehicles aware of your location.
(-22°F).
Max. working pressure:
•
To be sure your vehicle won't
•
Do not use the sealing compound
6 bar (87 psi)
move, even when you're on fairly
after its expiration date which can
Size
level ground, always set your park-
be found on the label of the bottle.
ing brake.
Compressor: 161 X 150 X 55.8 mm
•
Keep away from children.
(6.3 X 5.9 X 2.2 in.)
•
Only use the TireMobilityKit for
sealing/inflation passenger car
Sealant bottle: 81 x ø 85 mm
tires. Do not use on motorcycles,
(3.2 x ø 3.3 in.)
bicycles or any other type of tires.
Compressor weight:
•
Do not remove any foreign objects-
735 g ± 25 g (1.62 lbs ± 0.06 lbs)
such as nails or screws -that have
Sealant volume:
penetrated the tire.
200 ml (12.2 cu. in.)
•
Before using the TireMobilityKit,
❈ Sealing compound and spare
read the precautionary advice
parts can be obtained and
printed on the sealant bottle!
replaced at an authorized vehicle
•
Provided the car is outdoors, leave
or tire dealer. Empty sealing com-
the engine running. Otherwise
pound bottles may be disposed of
operating the compressor may
at home. Liquid residue from the
eventually drain the car battery.
sealing compound should be dis-
posed of by your vehicle or tire
dealer or in accordance with local
waste disposal regulations.
6
21
YN ENG 6.QXP
28.11.2016
16:06 Page 22
What to do in an emergency
TIRE PRESSURE MONITORING SYSTEM (TPMS) (IF EQUIPPED)
Each tire, including the spare (if pro-
Please note that the TPMS is not a
vided), should be checked monthly
substitute for proper tire mainte-
when cold and inflated to the inflation
nance, and it is the driver’s responsi-
pressure recommended by the vehi-
bility to maintain correct tire pres-
cle manufacturer on the vehicle plac-
sure, even if under-inflation has not
ard or tire inflation pressure label. (If
reached the level to trigger illumina-
your vehicle has tires of a different
tion of the TPMS low tire pressure
size than the size indicated on the
telltale.
vehicle placard or tire inflation pres-
Your vehicle has also been equipped
sure label, you should determine the
with a TPMS malfunction indicator to
proper tire inflation pressure for
indicate when the system is not
those tires.)
OYN069013
operating properly. The TPMS mal-
As an added safety feature, your
function indicator is combined with
(1) Low tire pressure telltale /
vehicle has been equipped with a tire
the low tire pressure telltale. When
TPMS malfunction indicator
pressure monitoring system (TPMS)
the system detects a malfunction,
(2) Low tire pressure position telltale
that illuminates a low tire pressure
the telltale will flash for approximate-
telltale when one or more of your
ly one minute and then remain con-
tires is significantly under-inflated.
tinuously illuminated. This sequence
Accordingly, when the low tire pres-
will continue upon subsequent vehi-
sure telltale illuminates, you should
cle start-ups as long as the malfunc-
stop and check your tires as soon as
tion exists. When the malfunction
possible, and inflate them to the
indicator is illuminated, the system
proper pressure. Driving on a signifi-
may not be able to detect or signal
cantly under-inflated tire causes the
low tire pressure as intended. TPMS
tire to overheat and can lead to tire
malfunctions may occur for a variety
failure. Under-inflation also reduces
of reasons, including the installation
fuel efficiency and tire tread life, and
of replacement or alternate tires or
may affect the vehicle’s handling and
wheels on the vehicle that prevent
stopping ability.
the TPMS from functioning properly.
6 22
YN ENG 6.QXP
28.11.2016
16:06 Page 23
What to do in an emergency
Always check the TPMS malfunction
Low tire pressure tell-
After you replace the low pressure
telltale after replacing one or more
tale
tire with the spare tire, one of the fol-
tires or wheels on your vehicle to
lowing will happen:
ensure that the replacement or alter-
Low tire pressure posi-
•
The TPMS malfunction indicator
nate tires and wheels allow the TPMS
may blink for approximately
1
tion telltale
to continue to function properly.
minute and then remain continuous-
ly illuminated because the TPMS
When the tire pressure monitoring
sensor is not mounted on the spare
✽ NOTICE
system warning indicators are illumi-
wheel. (changed tire equipped with
If any of the below happens, we rec-
nated one or more of your tires is sig-
a sensor not in the vehicle)
ommend that the system be checked
nificantly under-inflated. The low tire
•
The TPMS malfunction indicator
by an authorized Kia dealer.
pressure position telltale light will
will remain continuously illuminated
1.The low tire pressure telltale/
indicate which tire is significantly
while driving because the TPMS
TPMS malfunction indicator do
under-inflated by illuminating the cor-
sensor is not mounted on the spare
not illuminate for 3 seconds when
responding position light.
wheel. (changed tire equipped with
the ignition switch is turned to the
If either telltale illuminates, immediate-
a sensor in the vehicle)
ON position or engine is running.
ly reduce your speed, avoid hard cor-
2.The TPMS malfunction indicator
nering and anticipate increased stop-
remains illuminated after blinking
ping distances. You should stop and
for approximately 1 minute.
check your tires as soon as possible.
3.The Low tire pressure position
telltale remains illuminated.
Inflate the tires to the proper pres-
sure as indicated on the vehicle’s
placard or tire inflation pressure label
located on the driver’s side center pil-
lar outer panel.
If you cannot reach a service station
or if the tire cannot hold the newly
added air, replace the low pressure
tire with a spare tire.
6 23
YN ENG 6.QXP
28.11.2016
16:06 Page 24
What to do in an emergency
TPMS (Tire Pressure
CAUTION
WARNING -
Monitoring System)
In winter or cold weather, the
Low pressure damage
malfunction indicator
low tire pressure telltale may be
Significantly low tire pressure
The TPMS malfunction indicator will
illuminated if the tire pressure
makes the vehicle unstable and
illuminate after it blinks for approxi-
was adjusted to the recom-
can contribute to loss of vehicle
mately one minute when there is a
mended tire inflation pressure
control and increased braking
problem with the Tire Pressure
in warm weather. It does not
distances.
Monitoring System.
mean your TPMS is malfunction-
Continued driving on low pres-
We recommend that the system be
ing because the decreased tem-
sure tires can cause the tires to
perature leads to a proportional
checked by an authorized Kia dealer to
overheat and fail.
determine the cause of the problem.
lowering of tire pressure.
When you drive your vehicle
from a warm area to a cold area
✽ NOTICE
or from a cold area to a warm
If there is a malfunction with the
area, or the outside temperature
TPMS, the low tire pressure position
is greatly higher or lower, you
telltale will not be displayed even
should check the tire inflation
though the vehicle has an under-
pressure and adjust the tires to
inflated tire.
the recommended tire inflation
pressure.
6 24
YN ENG 6.QXP
28.11.2016
16:06 Page 25
What to do in an emergency
Changing a tire with TPMS
If you drive the vehicle for about 10
You may not be able identify a low
minutes at speeds above 25 km/h
tire by simply looking at it. Always
If you have a flat tire, the low Tire
after replaceing the low pressure tire
use a good quality tire pressure
Pressure and Position telltales will
with the spare tire, one of the follow-
gauge to measure the tire's inflation
come on. We recommend that the
ing will happen:
pressure. Please note that a tire that
system be checked by an authorized
is hot (from being driven) will have a
Kia dealer.
•
The TPMS malfunction indicator
higher pressure measurement than a
may blink for approximately
1
tire that is cold (from sitting station-
minute and then remain continuous-
CAUTION
ary for at least 3 hours and driven
ly illuminated because the TPMS
We recommend that you use the
less than 1 mile (1.6 km) during that
sensor is not mounted on the spare
sealant approved by Kia.
wheel. (changed tire equipped with
3 hour period).
The sealant on the tire pressure
a sensor not in the vehicle)
Allow the tire to cool before measur-
sensor and wheel shall be elim-
•
The TPMS malfunction indicator
ing the inflation pressure. Always be
inated when you replace the tire
will remain continuously illuminated
sure the tire is cold before inflating to
with a new one.
while driving because the TPMS
the recommended pressure.
sensor is not mounted on the spare
A cold tire means the vehicle has
Each wheel is equipped with a tire
wheel. (changed tire equipped with
been sitting for 3 hours and driven for
a sensor in the vehicle)
less than 1 mile (1.6 km) in that 3
pressure sensor mounted inside the
tire behind the valve stem. You must
hour period.
use TPMS specific wheels. It is rec-
ommended that you have your tires
CAUTION
serviced by an authorized Kia dealer.
We recommend that you use the
sealant approved by Kia if your
vehicle is equipped with a Tire
Pressure Monitoring System.
The liquid sealant can damage
the tire pressure sensors.
6 25
Большое спасибо!
Ваше мнение очень важно для нас.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст