KIA Venga (2016 year). Manual — part 8
YN ENG 4.QXP
28.11.2016
15:32 Page 54
Features of your vehicle
ESC OFF indicator
Cruise indicator (if equipped)
Speed limit indicator (if equipped)
(if equipped)
CRUISE indicator
①
②
The ESC OFF indicator will illuminate
when the ignition switch is turned ON,
(1) Speed limit indicator
but should go off after approximately 3
The indicator illuminates when the cruise
(2) Set speed limit indicator
seconds. To switch to ESC OFF mode,
control system is enabled.
press the ESC OFF button. The ESC
The cruise indicator in the instrument
The speed limit indicator illuminates
OFF indicator will illuminate indicating
cluster is illuminated when the cruise
when the speed limit control system is
the ESC is deactivated.
control ON-OFF button on the steering
enabled.
wheel is pushed.
The speed limit indicator in the instru-
ment cluster illuminates when the speed
✽ NOTICE
The indicator goes off when the cruise
limit ON-OFF button on the steering
After reconnecting or recharging a dis-
control ON-OFF button is pushed again.
wheel is pressed.
charged battery, the ESC OFF indicator
For more information about the use of
cruise control, refer to
“Cruise control
If the "
" indicator is shown in the
may illuminate. In this case, turn the
steering wheel 360 degrees to the left
system” in section 5.
instrument cluster, it indicates no setting
of the speed limit.
and 360 degrees to the right while the
ignition switch is in the ON position.
The set speed limit will display when the
Cruise SET indicator
Then, restart the engine after the igni-
speed limit control switch (SET-/RES+) is
SET
tion is off. If the ESC OFF indicator
ON.
does not turn off, we recommend that
If you drive over the speed limit, the set
you contact an authorized Kia dealer.
The indicator illuminates when the cruise
speed limit will blink and chime will
control switch (SET- or RES+) is ON.
sound.
The cruise SET indicator in the instru-
The set speed limit turns off when the
ment cluster is illuminated when the
speed limit is cancelled by pressing the
cruise control switch (SET- or RES+) is
CANCEL button.
pushed.
The speed limit indicator goes off when
The cruise SET indicator does not illumi-
the speed limit is deactivated.
nate when the cruise control switch
For more information about the speed
(CANCEL) is pushed or the system is
limit control usage, refer to “Speed Limit
disengaged.
control System” in section 5.
4 54
YN ENG 4.QXP
28.11.2016
15:32 Page 55
Features of your vehicle
TPMS (Tire Pressure Monitoring
AUTO STOP indicator
System) indicator (if equipped)
WARNING
(if equipped)
Low tire pressure telltale /
Significantly low tire pressure
TPMS malfunction indicator
makes the vehicle unstable and can
contribute to loss of vehicle control
This indicator will illuminate when the
and increased braking distances.
engine enters the Idle Stop mode of the
Low tire pressure position
Continued driving on low pressure
ISG (Idle Stop and Go) system.
telltale
tires will cause the tires to overheat
When the automatic starting occurrs, the
and fail.
"AUTO STOP" indicator on the cluster
will blink for 5 seconds.
The low tire pressure telltale comes on
for 3 seconds after the ignition switch is
For more details, refer to the ISG (Idle
turned to the "ON" position.
WARNING - Safe stopping
Stop and Go) system on the front of
The low tire pressure and position tell-
• The TPMS cannot alert you to
chapter 5.
tales illuminate when one or more of your
severe and sudden tire damage
tires is significantly underinflated.
caused by external factors.
✽ NOTICE
The low tire pressure telltale will illumi-
• If you feel any vehicle instability,
When the engine automatically starts by
nate after it blinks for approximately one
immediately take your foot off the
the ISG system, some warning
minute when there is a problem with the
accelerator, apply the brakes
lights(ABS, ESC, ESC OFF, EPS or
Tire Pressure Monitoring System.
gradually and with light force,
Parking brake warning light) may turn
If this occurs, we recommend that the
and slowly move to a safe posi-
on for a few seconds.
system be checked by an authorized Kia
tion off the road.
This happens because of the low battery
dealer.
voltage. It does not mean the system is
For details, refer to the TPMS on chapter 6.
malfunctioning.
4 55
YN ENG 4.QXP
28.11.2016
15:32 Page 56
Features of your vehicle
KEY OUT indicator
Glow indicator
Fuel filter warning light
KEY
(if equipped)
(Diesel engine)
(Diesel engine)
OUT
When the ENGINE START/STOP button
The indicator illuminates when the igni-
This warning light illuminates for 3 sec-
is in the ACC or ON position, if any door
tion switch is in the ON position. The
onds after the ignition switch is set to the
is open, the system checks for the smart
engine can be started after the preheat
ON position and then it will go off. If it
key. If the smart key is not in the vehicle,
indicator light goes off. The illuminating
lights up while the engine is running, it
the indicator will blink, and if all doors are
time varies with the water temperature,
indicates that water has accumulated
closed, the chime (if equipped) will also
air temperature and battery condition.
inside the fuel filter. If this happens,
sound for about 5 seconds. The indicator
remove the water from the fuel filter. For
will go off while the vehicle is moving.
more information, refer to “Fuel filter” in
✽ NOTICE
Keep the smart key in the vehicle or
section 7.
If the engine does not start within 10
insert it in the smart key holder.
seconds after the preheating is complet-
ed, turn the ignition key once more to
CAUTION
Key reminder warning chime
the LOCK position for 10 seconds, and
When the fuel filter warning light is
(if equipped)
then to the ON position, in order to pre-
illuminated, engine power (vehicle
If the driver’s door is opened while the
heat again.
speed & idle speed) may decrease.
ignition key is left in the ignition switch
If you keep driving with the warning
(ACC or LOCK position), the key
light on, you can damage your vehi-
reminder warning chime will sound. This
CAUTION
cle's engine parts and injection sys-
is to prevent you from locking your keys
If the preheat indicator continues to
tem of the Common Rail.
in the vehicle. The chime sounds until the
illuminate or blink on and off after
If this occurs, we recommend that
key is removed from the ignition switch or
the engine has warmed up or while
the system be checked by an author-
the driver’s door is closed.
driving, we recommend that the
ized Kia dealer.
system be checked by an author-
ized Kia dealer.
4 56
YN ENG 4.QXP
28.11.2016
15:32 Page 57
Features of your vehicle
REAR PARKING ASSIST SYSTEM (IF EQUIPPED)
WARNING
The rear parking assist system is a
supplementary function only. The
operation of the rear parking assist
system can be affected by several
factors
(including environmental
conditions). It is the responsibility
of the driver to always check the
area behind the vehicle before and
while backing up.
Sensors
OYN049046
OYN045128
The rear parking assist system assists
Operation of the rear parking
the driver during backward movement of
assist system
the vehicle by chiming if any object is
Operating condition
sensed within a distance of 120 cm (47
• This system will activate when the indi-
in.) behind the vehicle. This system is a
cator on the rear parking assist OFF
supplemental system and it is not intend-
button is not illuminated. If you desire
ed to nor does it replace the need for
to deactivate the rear parking assist
extreme care and attention of the driver.
system, press the rear parking assist
The sensing range and objects
OFF button again. (The indicator on
detectable by the back sensors are limit-
the button will illuminate.) To turn the
ed. Whenever backing-up, pay as much
system on, press the button again.
attention to what is behind you as you
(The indicator on the button will go off.)
would in a vehicle without a rear parking
assist system.
• This system will activate when backing
up with the ignition switch ON.
If the vehicle is moving at a speed over
5 km/h (3 mph), the system may not be
activated correctly.
4 57
YN ENG 4.QXP
28.11.2016
15:32 Page 58
Features of your vehicle
• The sensing distance while the rear
Non-operational conditions of
The detecting range may decrease
parking assist system is in operation is
rear parking assist system
when:
approximately 120 cm (47 in.).
1. The sensor is stained with foreign mat-
The rear parking assist system may
• When more than two objects are
ter such as snow or water. (The sens-
not operate properly when:
sensed at the same time, the closest
ing range will return to normal when
1. Moisture is frozen to the sensor. (It will
one will be recognized first.
removed.)
operate normally when the moisture
2. Outside air temperature is extremely
has been cleared.)
Types of warning sound
hot or cold.
2. The sensor is covered with foreign
• When an object is 120 cm to 61 cm (47
matter, such as snow or water, or the
in. to
24 in.) from the rear bumper:
The following objects may not be rec-
sensor cover is blocked. (It will operate
Buzzer beeps intermittently
ognized by the sensor:
normally when the material is removed
• When an object is 60 cm to 31 cm (23
or the sensor is no longer blocked.)
1. Sharp or slim objects such as ropes,
in. to
12 in.) from the rear bumper:
chains or small poles.
3. Driving on uneven road surfaces
Buzzer beeps more frequently
(unpaved roads, gravel, bumps, gradi-
2. Objects which tend to absorb the sen-
• When an object is within 30 cm (11 in.)
ent).
sor frequency such as clothes, spongy
of the rear bumper:
4. Objects generating excessive noise
material or snow.
Buzzer sounds continuously.
(vehicle horns, loud motorcycle
3. Undetectable objects smaller than 1 m
engines, or truck air brakes) are within
(40 in.) and narrower than 14 cm (6 in.)
range of the sensor.
in diameter.
5. Heavy rain or water spray exists.
6. Wireless transmitters or mobile phones
are within range of the sensor.
7. The sensor is covered with snow.
8. Trailer towing.
4 58
YN ENG 4.QXP
28.11.2016
15:32 Page 59
Features of your vehicle
Rear parking assist system pre-
✽ NOTICE
Self-diagnosis
cautions
This system can only sense objects with-
If you don’t hear an audible warning
•
The rear parking assist system may
in the range and location of the sensors;
sound or if the buzzer sounds intermit-
not sound sequentially depending on
It can not detect objects in other areas
tently when shifting the gear to the R
the speed and shapes of the objects
where sensors are not installed. Also,
(Reverse) position in operating condition,
detected.
small or slim objects, such as poles or
this may indicate a malfunction in the rear
objects located between sensors may not
parking assist system. If this occurs, we
•
The rear parking assist system may
be detected by the sensors.
recommend that the system be checked
malfunction if the vehicle bumper
Always visually check behind the vehi-
by an authorized Kia dealer.
height or sensor installation has been
modified or damaged. Any non-factory
cle when backing up.
Be sure to inform any drivers of the
installed equipment or accessories
vehicle that may be unfamiliar with the
WARNING
may also interfere with the sensor per-
system regarding the systems capabili-
Your new vehicle warranty does not
formance.
ties and limitations.
cover any accidents or damage to
•
The sensor may not recognize objects
the vehicle or injuries to its occu-
less than 40 cm (15 in.) from the sen-
pants due to a rear parking assist
sor, or it may sense an incorrect dis-
WARNING
system malfunction. Always drive
tance. Use caution.
Pay close attention when the vehi-
safely and cautiously.
•
When the sensor is frozen or stained
cle is driven close to objects on the
with snow, dirt, or water, the sensor
road, particularly pedestrians, and
may be inoperative until the stains are
especially children. Be aware that
removed using a soft cloth.
some objects may not be detected
•
Do not push, scratch or strike the sen-
by the sensors, due to the object’s
sor. Sensor damage could occur.
distance, size or material, all of
which can limit the effectiveness of
the sensor. Always perform a visu-
al inspection to make sure the vehi-
cle is clear of all obstructions
before moving the vehicle in any
direction.
4 59
YN ENG 4.QXP
28.11.2016
15:32 Page 60
Features of your vehicle
REARVIEW CAMERA (IF EQUIPPED)
The rearview camera will activate when
✽ NOTICE
the back-up light is ON with the ignition
The warning "Warning ! Check sur-
switch ON and the shift lever in the R
roundings for safety " will appear on the
(Reverse) position.
rearview display when the rearview
This system is a supplemental system
camera is activated.
that shows behind the vehicle through
the rearview display mirror while back-
ing-up.
WARNING
The rearview camera may be turned off
• This system is a supplementary
by pressing the ON/OFF button (1) when
function only. It is the responsibil-
■ Type A
the rearview camera is activated.
ity of the driver to always check
Rear view display
the inside/outside rearview mirror
To turn the camera on again, press the
and the area behind the vehicle
ON/OFF button (1) again when the igni-
before and while backing up
tion switch is on and the shift lever in R
because there is a dead zone that
(Reverse). Also, the camera will turn on
can't see through the camera.
automatically whenever the ignition
• Always keep the camera lens
switch is turned off and on again.
clean. If lens is covered with for-
Detailed information for the rearview
eign matter, the camera may not
camera (Type B) is described in a sepa-
operate normally.
rately supplied manual.
■ Type B
Rear view display
OYN049134/OYN046135/OYN046140
4 60
YN ENG 4.QXP
28.11.2016
15:32 Page 61
Features of your vehicle
HAZARD WARNING FLASHER
LIGHTING
■ Type A
Battery saver function
Headlight escort function
•
The purpose of this feature is to pre-
(if equipped)
vent the battery from being dis-
If you turn the ignition switch to the ACC
charged. The system automatically
or OFF position with the headlights ON,
turns off the parking lights when the
the headlights (and/or tail lights) remain
driver removes the ignition key and
on for about 20 minutes. However, if the
opens the driver-side door.
driver’s door is opened and closed, the
•
With this feature, the parking lights will
headlights are turned off after 30 sec-
turn off automatically if the driver parks
onds.
OYN065023L
on the side of road at night.
The headlights can be turned off by
■ Type B
pressing the lock button on the transmit-
If necessary, to keep the lights on
ter
(or smart key) twice or turning the
when the ignition key is removed, per-
light switch to the OFF or Auto position.
form the following:
However, if you turn the light switch to the
1) Open the driver-side door.
Auto position when it is dark outside, the
2) Turn the parking lights OFF and ON
headlights will not be turned off.
again using the light switch on the
steering column.
CAUTION
If the driver gets out of the vehicle
OYN065024L
through other doors (except driver's
The hazard warning flasher should be
door), the battery saver function
used whenever you find it necessary to
does not operate and the headlight
stop the vehicle in a hazardous location.
escort function does not turn off
When you must make such an emer-
automatically. Therefore, It causes
gency stop, always pull off the road as far
the battery to be discharged. In this
as possible.
case, make sure to turn off the lamp
The hazard warning lights are turned on
before getting out of the vehicle.
by pushing in the hazard switch. Both
turn signal lights will blink. The hazard
warning lights will operate even though
the key is not in the ignition switch.
To turn the hazard warning lights off,
push the switch again.
4
61
YN ENG 4.QXP
28.11.2016
15:32 Page 62
Features of your vehicle
Headlight welcome function
(if equipped)
When the headlight switch is in the ON or
AUTO position and all doors (and tail-
gate) are closed and locked, if you press
the door unlock button on the transmitter
(or smart key), the headlights will come
on for about 15 seconds.
If the headlight switch is in the AUTO
position, the function can only operate at
night.
At this time, if you press the door unlock
OED040045
OED040046
button again or door lock button on the
transmitter (or smart key), the headlights
Lighting control
Parking light position (
)
will turn off immediately.
The light switch has a Headlight and a
When the light switch is in the parking
Parking light position.
light position (1st position), the tail posi-
To operate the lights, turn the knob at the
tion, license and instrument panel lights
end of the control lever to one of the fol-
will turn ON.
lowing positions:
(1) OFF position
(2) Parking light position
(3) Headlight position
(4) Auto light position (if equipped)
4 62
YN ENG 4.QXP
28.11.2016
15:32 Page 63
Features of your vehicle
CAUTION
•
Never place anything over sensor
(1) located on the instrument
panel, this will ensure better auto-
light system control.
•
Don’t clean the sensor using a
window cleaner, the cleanser may
leave a light film which could
interfere with sensor operation.
•
If your vehicle has window tint or
other types of metallic coating on
OED040800
OYN049201
the front windshield, the Auto
Auto light position (if equipped)
light system may not work prop-
Headlight position (
)
erly.
When the light switch is in the AUTO light
When the light switch is in the headlight
position
(2nd position), the head, tail,
position, the taillights and headlights will
position, license and instrument panel
be turned ON or OFF automatically
lights are ON.
depending on the amount of light outside
the vehicle.
✽ NOTICE
The ignition switch must be in the ON
position to turn on the headlights.
4 63
YN ENG 4.QXP
28.11.2016
15:33 Page 64
Features of your vehicle
OED040801
OED040802
OED040804
High beam operation
To flash the headlights, pull the lever
Turn signals and lane change sig-
towards you. It will return to the normal
nals
To turn on the high beam headlights, push
(low beam) position when released. The
the lever away from you. Pull it back for
The ignition switch must be on for the
headlight switch does not need to be on
low beams.
turn signals to function. To turn on the
to use this flashing feature.
The high beam indicator will light when
turn signals, move the lever up or down
the headlight high beams are switched on.
(A). The green arrow indicators on the
To prevent the battery from being dis-
instrument panel indicate which turn sig-
charged, do not leave the lights on for a
nal is operating. They will self-cancel
prolonged time while the engine is not
after a turn is completed. If the indicator
continues to flash after a turn, manually
running.
return the lever to the O (OFF) position.
WARNING
Do not use high beam when there
are other vehicles. Using high beam
could obstruct the other driver's
vision.
4 64
YN ENG 4.QXP
28.11.2016
15:33 Page 65
Features of your vehicle
To signal a lane change, move the turn
■ Type A
signal lever slightly and hold it in position
(B). The lever will return to the O (OFF)
position when released.
If an indicator stays on and does not
flash or if it flashes abnormally, one of the
turn signal bulbs may be burned out and
will require replacement.
OED040806
■ Type B
✽ NOTICE
If an indicator flash is abnormally quick
or slow, a bulb may be burned out or
OYN049200
have a poor electrical connection in the
circuit.
Front fog light (if equipped)
Fog lights are used to provide improved
visibility when visibility is poor due to fog,
OAM049046L
rain or snow, etc. The fog lights will turn
on when the fog light switch (1) is turned
Rear fog light (if equipped)
on after the parklight is turned on and the
To turn the rear fog lights on, turn the
ignition is on.
rear fog light switch (1) to the on position
To turn off the fog lights, turn the fog light
when the headlight is turned on.
switch (1) to the O (OFF) position.
The rear fog lights turn on when the rear
fog light switch is turned on after the front
CAUTION
fog light switch (if equipped) is turned on
When in operation, the fog lights
and the headlight switch is in the park-
consume large amounts of vehicle
light position.
electrical power. Only use the fog
To turn the rear fog lights off, turn the rear
lights when visibility is poor.
fog light switch to the on position again.
4 65
YN ENG 4.QXP
28.11.2016
15:33 Page 66
Features of your vehicle
Daytime running light
Listed below are the examples of proper
(if equipped)
switch settings. For loading conditions
other than those listed below, adjust the
The Daytime Running Lights (DRL) can
switch position so that the beam level
make it easier for others to see the front
may be the nearest as the condition
of your vehicle during the day. DRL can
obtained according to the list.
be helpful in many different driving condi-
tions, and it is especially helpful after
dawn and before sunset.
Loading condition
Switch position
The DRL system will make the head-
Driver only
0
lights turn OFF when:
Driver + Front passenger
0
1. Headlight or front fog light switch is ON.
Full passengers
2. The engine is OFF.
OYN045047
1
(including driver)
Headlight leveling device
Full passengers (including
(if equipped)
To adjust the headlight beam level
driver) + Maximum per-
3
according to the number of the passen-
missible loading
gers and loading weight in the luggage
Driver + Maximum per-
area, turn the beam leveling switch.
5
The higher the number of the switch
missible loading
position, the lower the headlight beam
level. Always keep the headlight beam at
the proper leveling position, or headlights
may dazzle other road users.
4 66
YN ENG 4.QXP
28.11.2016
15:33 Page 67
Features of your vehicle
WIPERS AND WASHERS
A : Wiper speed control (front)
Windshield wipers (front)
■ Front
· 2 - High wiper speed
Operates as follows when the ignition
· 1 - Low wiper speed
switch is turned ON.
· --- - Intermittent wipe
: For a single wiping cycle, move the
· O - Off
lever to this position and release it
with the lever in the OFF position. The
·
- Single wipe
wipers will operate continuously if the
lever is held in this position.
B : Intermittent control wipe time
adjustment
O : Wiper is not in operation
--- : Wiper operates intermittently at the
C : Wash with brief wipes (front)*
same wiping intervals. Use this mode
in a light rain or mist. To vary the
speed setting, turn the speed control
D : Rear wiper/washer control*
knob.
■ Rear (if equipped)
·
- Continuous wipe
1 : Normal wiper speed
·
---
- Intermittent wipe
2 : Fast wiper speed
· O
- Off
E : Wash with brief wipes (rear)
✽ NOTICE
If there is heavy accumulation of snow
or ice on the windshield, defrost the
* : if equipped
windshield for about
10 minutes, or
until the snow and/or ice is removed
before using the windshield wipers to
ensure proper operation.
If you do not remove the snow and/or ice
OXM049230L/OAM049048L
before using the wiper and washer, it may
damage the wiper and washer system.
4 67
YN ENG 4.QXP
28.11.2016
15:33 Page 68
Features of your vehicle
CAUTION
CAUTION
To prevent possible damage to the
•
To prevent possible damage to
washer pump, do not operate the
the wipers or windshield, do not
washer when the fluid reservoir is
operate the wipers when the
empty.
windshield is dry.
•
To prevent damage to the wiper
blades, do not use gasoline,
kerosene, paint thinner, or other
WARNING
solvents on or near them.
Do not use the washer in freezing
•
To prevent damage to the wiper
temperatures without first warming
arms and other components, do
OXM049048E
the windshield with the defrosters;
not attempt to move the wipers
the washer solution could freeze on
manually.
Windshield washers (front)
the windshield and obscure your
•
To prevent possible damage to
In the O (OFF) position, pull the lever
vision.
the wipers and washer system,
gently toward you to spray washer fluid
use anti-freezing washer fluids in
on the windshield and to run the wipers
the winter season or cold weather.
1-3 cycles.
Use this function when the windshield is
dirty.
The spray and wiper operation will con-
tinue until you release the lever.
If the washer does not work, check the
washer fluid level. If the fluid level, you
will need to add appropriate non-abra-
sive windshield washer fluid to the wash-
er reservoir.
The reservoir filler neck is located in the
front of the engine compartment on the
passenger side.
4 68
YN ENG 4.QXP
28.11.2016
15:33 Page 69
Features of your vehicle
If the wiper switch is set in AUTO mode
when the ignition switch is ON, the wiper
will operate once to perform a self-check
of the system. Set the wiper to OFF posi-
tion when the wiper is not in use.
CAUTION
When the ignition switch is ON and
Rain sensor
the windshield wiper switch is
placed in the AUTO mode, use cau-
OYF049103
tion in the following situations to
avoid any injury to the hands or
OXM049103E
other parts of the body:
Rear window wiper and washer
•
Do not touch the upper end of the
switch
windshield glass facing the rain
sensor.
The rear window wiper and washer
•
Do not wipe the upper end of the
switch is located at the end of the wiper
windshield glass with a damp or
and washer switch lever. Turn the switch
wet cloth.
to desired position to operate the rear
wiper and washer.
•
Do not put pressure on the wind-
Rain sensor
shield glass.
- Normal wiper operation
OTFR040207
---
- Intermittent wipe
Auto control (if equipped)
O - Wiper is not in operation
The rain sensor located on the upper end
of the windshield glass senses the
amount of rainfall and controls the wiping
cycle for the proper interval. The more it
rains, the faster the wiper operates.
When the rain stops, the wiper stops.
To vary the speed setting, turn the speed
control knob (1).
4
69
YN ENG 4.QXP
28.11.2016
15:33 Page 70
Features of your vehicle
OXM049125L
Push the lever away from you to spray
rear washer fluid and to run the rear
wipers 1~3 cycles. The spray and wiper
operation will continue until you release
the lever.
4 70
Большое спасибо!
Ваше мнение очень важно для нас.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст