KIA Soul (2018 year). Manual — part 35
Maintenance
82
8
Description
Fuse rating
Protected component
MODULE 3
10A
HLLD_ACTR, TPMS_UNIT, BLIND_SPOT_DETECTOR, REAR_PARKING_ASSIST_SYSTEM_SNSR,
SMART_PARKING_ASSIST_SYSTEM_SNSR, SMART_PARKING_ASSIST_SYSTEM_UNIT,
LANE_DEPARTURE_WARNING_SYSTEM_UNIT, OIL_LEVEL_SNSR_EXTN
VACUUM PUMP 2
15A
VACUUM_PUMP
ECU
7.5A
ENGINE_CONTROL_UNIT, AIR_FLOW_SNSR, START_RLY_COIL, SMK_UNIT, SMATRA_IMMOBI-
LIZATION, GLOW_UNIT
IOD 2
15A
LDC_AMP(200W), AUDIO/UVO/AVN4.0_HEAD_UNIT
IOD 3
7.5A
E_CALL_UNIT
AEB
15A
AUTONOMOUS_EMERGENCY_BRAKING_UNIT
CLUSTER
10A
CLUSTER
TCU
15A
SPEED_SNSR (MT), BACK_UP_LAMP_SW, OIL_PUMP_INVERTER, INHIBITOR,
TRANSMISSION_CONTROL_UNIT
IOD 4
7.5A
TPMS_UNIT(POWER), CLUSTER, AIR_CONTROL_UNIT(MANUAL, AUTO), BCM, REAR-
PARKING_ASSIST_SYSTEM_BUZZER, OUTSIDE_MIRROR_FOLDING_RLY,
OUTSIDE_MIRROR_FOLDING_RLY_COIL, OUTSIDE_MIRROR_UNFOLDING_RLY, OUTSIDE_MIR-
ROR_UNFOLDING_RLY_COIL, RAIN_SNSR
SPARE 10A
-
SUNROOF 2
20A
SUNROOF_MOTOR (POWER)
P/SEAT DRV
30A
SEAT_EXTN_DRV(POWER)
SUNROOF 1
20A
SUNROOF_MOTOR (POWER)
8 83
Maintenance
Description
Fuse rating
Protected component
MDPS
7.5A
MDPS_UNIT
A/CON 2
7.5A
AIR_CONTROL_UNIT_MANUAL(MAX_BLOWER), AIR_CONTROL_UNIT_AUTO(BLOWER_MOTOR)
START
7.5A
E/R_FUSE & RELAY_BOX(RELAY - START / SUB START), PDM
IOD 1
7.5A
GLOVE_BOX_LAMP, DOOR_WARNING_SW, OVER_HEAD_CONSOLE_LAMP, PERSONAL_LAMP,
SUNVISOR_LAMP, LUGGAGE_LAMP, PORTABLE_LAMP(DOOR)
PDM 2
7.5A
SMK_UNIT(BATT_CPU), SMATRA_IMMOBILIZATION(BATT)
P/SEAT PASS
30A
SEAT_EXTN_PASS(POWER)
PDM 1
20A
SMK_UNIT(POWER)
BRAKE SWITCH
10A
STOP_LAMP_SW(NORMAL_OPEN), SMK_UNIT
Maintenance
84
8
Engine compartment fuse panel
✽
✽
NOTICE
The actual fuse/relay panel label
may differ from equipped items.
OPS073013
OPS076106N
8 85
Maintenance
Engine compartment fuse panel
Description
Fuse rating
Protected component
IG1
40A
IGN_SW(B1), BUTTON_START_RLY(IG1), BUTTON_START_RLY(ACC)
BLOWER
40A
BLOWER_RLY, BLOWER_MOTOR
REAR HEATED
40A
REAR_GLASS_HEATED_RLY, REAR_GLASS_HEATED_RLY_COIL
ECU 2
30A
MAIN_RLY, MAIN_RLY_COIL
ECU 3
15A
ECU(AFTER_AIN_RELAY)
IGN COIL
20A
IGNITION_COIL(POWER)
ECU 1
20A
ECU(AFTER_MAIN_RELAY)
SENSOR 1
10A
STOP_LAMP_SW(NORMAL_CLOSE), O2_SNSR, PURGE_CONTROL_SOLENOID_VALVE, OCV,
PCSV, VIS, CAM_P_SNSR, CAM POSITION SENSOR, VGT_VACCUM
SENSOR 2
10A
CMP, COOLING_FAN_LOW_RLY_COIL, AIR_FLAP_SNSR, VIS , EGR_VALVE, O2_SNSR,
LAMBDA_SNSR, WGV, EGR_ACTUATOR
INJECTOR
10A
-
B/UP LAMP
10A
RR_COMBI_LAMP(BACK_UP_LAMP)
WIPER
10A
ECU(WIPER_SWITCH)
FUEL PUMP
15A
FUEL_PUMP_MOTOR
HORN
15A
HORN_RLY, HORN_RLY_COIL, HORN
TCU4
15A
TRANSMISSION_CONTROL_UNIT
A/CON
10A
A/CON_RLY
Maintenance
86
8
Description
Fuse rating
Protected component
H/LAMP WASHER
20A
HEAD_LAMP_WASHER_RLY, HEAD_LAMP_WASHER_RLY_COIL, HEAD_LAMP_WASHER_MOTOR
POWER OUTLET 4
20A
P_OUTLET
B+ 1
50A
SMART_JUNCTION_BLOCK(B+1)
B+ 2
50A
SMART_JUNCTION_BLOCK(B+2)
TCU 3
30A
TRANSMISSION_CONTROL_UNIT
B+ 3
50A
SMART_JUNCTION_BLOCK(B+3)
IG2
40A
IGN_SW(IG2), BUTTON_START_RLY(IG2), START_RLY
MDPS
80A
MDPS_UNIT
ALT (GAMMA)
125A
ALTERNATOR
ALT (NU)
180A
TCU
20A
TRANSMISSION_CONTROL_UNIT
DEICER
20A
DEICER
ECU 4
15A
ECU(BATT_DIRECT)
ECU 5
15A
ECU(BATT_DIRECT)
POWER OUTLET 3
20A
P_OUTLET
VACUUM PUMP 1
30A
VACUUM_PUMP
8 87
Maintenance
Description
Fuse rating
Protected component
COOLING FAN
40A (*/**)
60A (***)
COOLING_FAN_MOTOR, SUB_FUEL_PUMP, SUB_FUEL_VALVE, COOLING_FAN_PWM_MOTOR
INVERTER (**)
TCU2 (*/****)
50A
OIL_PUMP_INVERTER, TRANSMISSION_CONTROL_UNIT
ABS 1
40A
ABS/ESP_UNIT(MOTOR)
ABS 2
30A
ABS/ESP_UNIT(SOLENOID)
Maintenance
88
8
LIGHT BULBS
Bulb replacement precaution
Please keep extra bulbs on hand
with appropriate wattage ratings in
case of emergencies.
Refer to “Bulb Wattage” in chapter 9.
When changing lamps, first turn off
the engine at a safe place, firmly
apply the parking brake and detach
the battery’s negative (-) terminal.
Use only bulbs of the specified
wattage.
✽
✽
NOTICE
• If the light bulb or lamp connector
is removed while the lamp is still
on, the fuse box's electronic sys-
tem may log it as a malfunction.
Therefore, a lamp malfunction
incident may be recorded as a
Diagnostic Trouble Code (DTC) in
the fuse box.
• It is normal for an operating lamp
to flicker momentarily. This is due
to a stabilization function of the
vehicle’s electronic control device.
If the lamp lights up normally
after momentarily blinking, then
it is functioning as normal.
However, if the lamp continues to
flicker several times or turns off
completely, there may be an error
in the vehicle’s electronic control
device. Please have the vehicle
checked by an authorized Kia
dealer immediately.
WARNING
- Working on
the lights
Prior to working on the light,
firmly apply the parking brake,
ensure that the ignition switch
is turned to the LOCK position
and turn off the lights to avoid
sudden movement of the vehi-
cle and burning your fingers or
receiving an electric shock.
CAUTION -
Light replace-
ment
Be sure to replace the burned-
out bulb with one of the same
wattage rating. Otherwise, it
may cause damage to the fuse
or electric wiring system.
CAUTION -
Headlamp
Lens
To prevent damage, do not
clean the headlamp lens with
chemical solvents or strong
detergents.
8 89
Maintenance
If you don’t have the necessary tools,
the correct bulbs and the expertise,
consult an authorized Kia dealer. In
many cases, it is difficult to replace
vehicle light bulbs because other
parts of the vehicle must be removed
before you can get to the bulb. This is
especially true if you have to remove
the headlamp assembly to get to the
bulb(s).
Removing/installing the headlamp
assembly can result in damage to
the vehicle.
If non-genuine parts or substandard
bulbs are used, it may lead to blow-
ing a fuse or other wiring damages.
Do not install extra lamps or LEDs to
the vehicle. If additional lights are
installed, it may lead to lamp mal-
functions and flickering. Additionally,
the fuse box and other writing may
be damaged.
Light bulb position (Front)
(1) Front turn signal lamp
(2) Headlamp (Low/High)
(3) Side marker
(4) Headlamp (High)
(5) Headlamp (Low)
(6) Position lamp (LED Type)
(7) Position lamp/Daytime running
lamp (LED Type)
(8) Front fog lamp
■
Type B
■
Type A
OPS076021N
OPS076020N
■
Type C
OPS076134N
Maintenance
90
8
Light bulb position (Rear)
(1) Tail lamp (Bulb type)
(2) Tail and stop lamp (Bulb type)
(3) Rear turn signal lamp
(4) Back-up lamp
(5) Tail lamp (Bulb type)
(6) Tail and stop lamp (LED type)
Headlamp (HID type) bulb
replacement
If the light bulb does not operate,
have the vehicle checked by an
authorized Kia dealer.
✽
✽
NOTICE
HID lamps have superior perform-
ance vs. halogen bulbs. HID lamps
are estimated by the manufacturer to
last twice as long or longer than halo-
gen bulbs depending on their fre-
quency of use. They will probably
require replacement at some point in
the life of the vehicle. Cycling the
headlamps on and off more than typ-
ical use will shorten HID lamps life.
HID lamps do not fail in the same
manner as halogen incandescent
lamps. If a headlamp goes out after a
period of operation but will immedi-
ately relight when the headlamp
switch is cycled it is likely the HID
lamp needs to be replaced. HID
lamping components are more com-
plex than conventional halogen bulbs
thus have higher replacement cost.
OPS076030L
OPS076029L
■
Type A
■
Type B
WARNING
- HID
Headlamp (if equipped)
Do not attempt to replace or
inspect the HID headlamp
(XENON bulb) due to electric
shock danger. If the light bulb
does not operate, have your
vehicle checked by an author-
ized Kia dealer.
8 91
Maintenance
Headlamp (Low/High beam)
bulb replacement
1. Turn off the engine and open the
hood. Disconnect the negative
battery cable.
2. Disconnect the power connector
front the back of the headlamp
assembly.
3. Loosen the retaining bolts.
4. Pull out the end of the front
bumper.
5. Remove the headlamp assembly
from the body of the vehicle.
❈
If you can reach the bulb without
removing the headlamp assembly,
you do not need to do step 3,4 and
5.
OPS073051
OPS076028L
OPS076046L
Maintenance
92
8
6. Remove the headlamp bulb cover
by turning it counterclockwise.
7. Disconnect the headlamp bulb
socket-connector.
8. Unsnap the headlamp bulb retain-
ing wire by depressing the end
and pushing it upward.
9. Remove the bulb from the head-
lamp assembly.
10. Install a new headlamp bulb and
snap the headlamp bulb retaining
wire into position by aligning the
wire with the groove on the bulb.
11. Connect the headlamp bulb
socket connector.
12. Install the headlamp bulb cover
by turning it clockwise.
13. Connect the power connector to
the back of the headlamp assem-
bly.
14. Reinstall the headlamp assembly
to the body of the vehicle.
✽
✽
NOTICE
If the headlamp aiming adjustment
is necessary after the headlamp
assembly is reinstalled, we recom-
mend that you consult an authorized
Kia dealer.
Headlamp bulb
OPS073047
OPS073023
WARNING
- Halogen
bulbs
Handle halogen bulbs with care.
• Halogen bulbs contain pres-
surized gas that will produce
flying pieces of glass if bro-
ken.
OHD076046
8 93
Maintenance
• Always handle them carefully, and
avoid scratches and abrasions. If
the bulbs are lit, avoid contact with
liquids. Never touch the glass with
bare hands. Residual oil may
cause the bulb to overheat and
burst when lit. A bulb should be
operated only when installed in a
headlamp.
• If a bulb becomes damaged or
cracked, replace it immediately
and carefully dispose of it.
• Wear eye protection when chang-
ing a bulb. Allow the bulb to cool
down before handling it.
Front turn signal lamp bulb
replacement
1. Turn off the engine and open the
hood. Disconnect the negative
battery cable.
2. Disconnect the power connector
front the back of the headlamp
assembly.
3. Loosen the retaining bolts.
OPS073051
OPS076028L
Maintenance
94
8
■
Type B
■
Type A
OPS073049
OPS073024
■
Type C
OPS076125L
4. Pull out the end of the front
bumper.
5. Remove the headlamp assembly
from the body of the vehicle.
❈
If you can reach the bulb without
removing the headlamp assembly,
you do not need to do step 3,4 and
5.
6. Remove the socket from the
assembly by turning the socket
counterclockwise until the tabs on
the socket align with the slots on
the assembly.
7. Remove the bulb from the socket
by pressing it in and rotating it
counterclockwise until the tabs on
the bulb align with the slots in the
socket.
8. Insert a new bulb by inserting it
into the socket and rotating it until
it locks into place.
9. Install the socket in the assembly
by aligning the tabs on the socket
with the slots in the assembly and
turning the socket clockwise.
10. Reinstall the lamp assembly to
the body of the vehicle.
OPS076046L
8 95
Maintenance
Front side marker bulb
replacement
1. Turn off the engine and open the
hood. Disconnect the negative
battery cable.
2. Disconnect the power connector
front the back of the headlamp
assembly.
3. Loosen the retaining bolts.
4. Pull out the end of the front
bumper.
5. Remove the headlamp assembly
from the body of the vehicle.
❈
If you can reach the bulb without
removing the headlamp assembly,
you do not need to do step 3,4 and
5.
OPS073051
OPS076028L
OPS076046L
Maintenance
96
8
6. Remove the socket from the
assembly by turning the socket
counterclockwise until the tabs on
the socket align with the slots on
the assembly.
7. Pull the bulb out of the socket.
8. Insert a new bulb into the socket.
9. Install the socket into the assem-
bly by aligning the tabs on the
socket with the slots on the
assembly and turning the socket
clockwise.
10. Reinstall the lamp assembly to
the body of the vehicle.
Position lamp + DRL (LED
type) bulb replacement
If the position lamp + DRL (1) does
not operate, we recommend that you
checked an authorized Kia dealer.
Front fog lamp bulb replace-
ment
1. Remove the front bumper under
cover.
2. Reach your hand into the back of
the front bumper.
OPS073025
OPS076028L
OPS073027
OPS076127L
8 97
Maintenance
3. Disconnect the power connector
from the socket.
4. Remove the bulb-socket from the
housing by turning the socket
counter clockwise until the tabs on
the socket align with the slots on
the housing.
5. Install the new bulb-socket into the
housing by aligning the tabs on
the socket with the slots in the
housing. Push the socket into the
housing and turn the socket clock
wise.
6. Connect the power connector to
the socket.
7. Reinstall the front bumper under
cover.
✽
✽
NOTICE
If the fog lamp aiming adjustment is
necessary after the fog lamp assem-
bly is reinstalled, we recommend that
you consult an authorized Kia dealer.
Side repeater lamp (LED type)
bulb replacement
If the Side repeater lamp (LED type)
does not operate, we recommend
that you checked an authorized Kia
dealer.
OPS073035
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст