KIA Sedona (2019 year). Manual — part 2

Safety features of your vehicle

12

3

Storing positions into memory
using the buttons on the door

Storing driver’s seat positions
1. Shift the shift lever into P while the

engine start/stop button is ON or
ignition switch ON.

2. Adjust the driver’s seat and out-

side rearview mirror comfortable
for the driver.

3. Press SET button on the control

panel. The system will beep once.

4. Press one of the memory buttons

(1 or 2) within 4 seconds after
pressing the SET button. The sys-
tem will beep twice when memory
has been successfully stored.

✽

✽

NOTICE

When recalling an adjustment mem-
ory button while sitting in the vehi-
cle, you can be surprised by the set-
ting chosen if the memory has been
adjusted by someone else. If that
occurs, immediately push the seat
position control knob in the direc-
tion of the desired position to stop
further undesired movement.

Recalling positions from memory
1. Shift the shift lever into P while the

engine start/stop button is ON or
ignition switch ON.

2. To recall the position in the memo-

ry, press the desired memory but-
ton (1 or 2). The system will beep
once, then the driver’s seat will
automatically adjust to the stored
position.

Adjusting the control switch for the
driver’s seat while the system is
recalling the stored position will
cause the movement to stop and
move in the direction that the control
switch is moved.

3 13

Safety features of your vehicle

Easy access function
(if equipped)

The system will move the driver's
seat automatically as follows:
• Without smart key system

- It will move the driver’s seat rear-

ward when the ignition key is
removed.

- It will move the driver’s seat for-

ward when the ignition key is
inserted.

• With smart key system

- It will move the driver’s seat rear-

ward when the engine start/stop
button is changed to the OFF
position.

- It will move the driver’s seat for-

ward when the engine start/stop
button is changed to the ACC or
START position.

You can activate or deactivate this fea-
ture. Refer to "User settings" in chap-
ter 4.

Headrest (for front seat)

The driver's and front passenger's
seats are equipped with a headrest
for the occupant's safety and comfort.
The headrest not only provides com-
fort for the driver and front passenger,
but also helps protect the head and
neck in the event of a rear collision.

For maximum effectiveness in case
of an accident, the headrest should
be adjusted so the middle of the
headrest is at the same height of the
center of gravity of an occupant's
head. Generally, the center of gravity
of most people's head is similar with
the height of the top of their eyes.
Also, adjust the headrest as close to
your head as possible. For this rea-
son, the use of a cushion that holds
the body away from the seatback is
not recommended.

OYP034285N

Safety features of your vehicle

14

3

Adjusting the height up and down

To raise the headrest, pull it up to the
desired position (1). To lower the
headrest, push and hold the release
button (2) on the headrest support
and lower the headrest to the desired
position (3).

✽

✽

NOTICE

If you recline the seatback towards
the front with the headrest and seat
cushion raised, the headrest may
come in contact with the sunvisor or
other parts of the vehicle.

OYP034010

OYFH034205

WARNING

- Headrest

removal/adjustment

• Do not operate the vehicle

with the headrests removed.
Headrests can provide critical
neck and head support in a
crash.

• Do not adjust the headrest

height while the vehicle is in
motion. Driver may lose con-
trol of the vehicle.

3 15

Safety features of your vehicle

Removal and reinstallation

To remove the headrest:
1. Recline the seatback (2) with the

recline lever or switch (1).

2. Raise headrest as far as it can go.

3. Press the headrest release button

(3) while pulling the headrest up
(4).

To reinstall the headrest :
1. Put the headrest poles (2) into the

holes while pressing the release
button (1).

2. Recline the seatback (4) with the

recline lever or switch (3).

WARNING

NEVER allow anyone to ride in a
seat with the headrest removed.

OYP034012

OYP034013N

■ Type A

■ Type B

OYP034014

OYP034015N

■ Type A

■ Type B

Safety features of your vehicle

16

3

3. Adjust the headrest to the appro-

priate height.

Seatback pocket

The seatback pocket is provided on
the back of the front passenger’s and
driver’s seatbacks.

OYP044077K

WARNING

- Seatback

pockets

Do not put heavy or sharp
objects in the seatback pockets.
In an accident they could come
loose from the pocket and
injure vehicle occupants.

WARNING

- Headrest

Reinstallation

To reduce the risk of injury to
the head or neck, always make
sure the headrest is locked into
position and adjusted properly
after reinstalling.

3 17

Safety features of your vehicle

Rear seat adjustment

Forward and backward
(2nd row seat)

To move the seat forward or back-
ward:
1. Pull the seat slide adjustment lever

up and hold it.

2. Slide the seat to the position you

desire.

3. Release the lever and make sure

the seat is locked in place.

Adjust the seat before driving, and
make sure the seat is locked securely
by trying to move forward and back-
ward without using the lever. If the
seat moves, it is not locked properly.

❈ 7-seater SXL Seat
To move the seat inward, first turn
the left/right control lever, and then
move the seat to the farthest back
position.

Left and Right
(2nd row seat, SXL package)

To move the seat left side or right
side:
1. Pull the seat slide adjustment lever

up and hold it.

2. Slide the seat to the position you

desire.

3. Release the lever and make sure

the seat is locked in place.

Adjust the seat before driving, and
make sure the seat is locked securely
by trying to move left side and right
side without using the lever. If the seat
moves, it is not locked properly.

OYP034202N

OYP034291N

■ for SXL package

OYP034293N

Safety features of your vehicle

18

3

Seatback angle

To recline the seatback:
1. Pull up the seatback recline lever

(for 2nd row outboard seat) or
strap (for 2nd row center or 3rd
row seat).

2. Hold the lever or strap and adjust

the seatback of the seat to the
position you desire.

3. Release the lever or strap and

make sure the seatback is locked
in place. (The lever MUST return
to its original position for the seat-
back to lock.)

OYP034292N

■ 2nd row seat for SXL package

OYP034205N

■ 3rd row seat

OYP034204N

■ 2nd row seat

OYP034206N

■ 2nd row center seat (if equipped)

3 19

Safety features of your vehicle

Walk-in seat (2nd row seat)

To get in or out of the 3rd row seat,
1. Lift the armrest up and lower the

head rest to the lowest position (if
necessary).

2. Pull up the walk-in lever (1) or pull

the walk-in strap (2) on the 2nd
row seat to allow passenger to exit
3rd row seat.

3.At this time, 2nd row seat position

will be changed to stand up posi-
tion, and the head rest will be fold-
ed automatically.
After getting in or out, push the 2nd
row seat to the original position
until it clicks into place and check
the head rest position (unfolded
position).
Make sure that the seat is locked in
place.

Walk-in seat
(2nd row seat for SXL package)

To get in or out of the 3rd row seat,

OYP034209N

OYP034210N

OYP036299N

OYP036321N

Safety features of your vehicle

20

3

1.Lift the armrest up , lower the head-

rests to the lowest position and
slide the seat inside. (if necessary).

2.Pull the walk-in strap (1) or recline

lever (2) on the 2nd row seat when
the passenger gets in or out of the
3rd row seat.

3.Push the 2nd row seat to forward.

After getting out, push the 2nd row
seat to the original position until it
clicks into place.
Make sure that the seat is locked in
place. In the walk-in position, the
front and back sliding function is
not fixed.

Leg support
(2nd row seat for SXL package)

To use the leg support :
1. Pull the leg support lever up and

hold it.

2. Adjust the angle and length of the

leg support while holding the leg
support. When using the leg rest,
move the seat to the inner position,
and then toward the back. If the seat
is not moved far back, it may come
in contact with the first row seat.

3. Release the lever and make sure

the leg support is locked in place.

Folding the rear seat

The rear seatbacks can be folded to
facilitate carrying long items or to
increase the luggage capacity of the
vehicle.

OYP034294N

WARNING

Never attempt to adjust the 2nd
row seat while the vehicle is
moving or the seat is occupied
as the seat may suddenly move
and cause the passenger on the
seat to be injured.

WARNING

- Folded down

seatback

Never allow passengers sit on
top of the folded down seatback
while the vehicle is moving. This
is not a proper seating position
and no seat belts are available
for use.
This could result in serious
injury or death in case of an
accident or sudden stop.

3 21

Safety features of your vehicle

To fold down the rear seatback
1. Insert the rear seat belt buckle in

the pocket between the rear seat-
back and cushion, and insert the
rear seat belt webbing in the guide
to prevent the seat belt from being
damaged.

2. Set the front seatback to the

upright position and if necessary,
slide the front seat forward.

3. Lower the rear headrests to the

lowest position.

OYP034267N

OYP034212N

■ 2nd row center seat (for 8 passenger vehicle)

■ 3rd row seat

WARNING

- Objects

Objects carried on the folded
down seatback should not
extend higher than the top of
the front seatbacks. This could
allow cargo to slide forward and
cause injury or damage during
sudden stops.

OYP034214N

Safety features of your vehicle

22

3

4. Pull on the seatback folding lever

or strap, then fold the seat toward
the front of the vehicle. When you
return the seatback to its upright
position, always be sure it has
locked into position by pushing on
the top of the seatback.

5. To use the rear seat, lift and pull

the seatback backward by pulling
on the folding lever or strap.
Pull the seatback firmly until it
clicks into place. Make sure the
seatback is locked in place.

6. Return the rear seat belt to the

proper position.

Removing the tumble seat
(for 8 passenger vehicle)

1. Insert the seat belt in the belt

assembly cover.

2. Insert the seat belt buckle in the

seat cushion pocket.

OYP034216N

OYP034218N

OYP037219N

■ 2nd row seat

■ 2nd row center seat (for 8 passenger vehicle)

OYP034220N

OYP034267N

3 23

Safety features of your vehicle

3. Lower the headrest to the lowest

position.

4. Slide the seat to the farthest rear-

ward.

5. Fold the seat back by pull up the

recline strap.

6. Pull the removal strap and lift the

rear portion of the seat cushion.

7. Pull up the catch release lever

under the front of the seat cushion
while reclining the folded seat
rearward slightly to release the
front catches from the anchors.

8. Remove the entire seat from the

floor.

OYP034221N

OYP034223N

OYP034227N

Safety features of your vehicle

24

3

Installing the tumble seat
(for 8 passenger vehicle)

1. Put the front anchor strikers along

the front anchors on the floor.

2. Insert two front anchor strikers into

the front anchors.

3. Lift the rear portion of the seat

cushion then push down firmly to
lock the catches into the rear
anchors until an audible “click” is
heard.

4.Make sure the green mark on the

rear seat cushion frame is visible
and the catches are locked in posi-
tion by moving the seat forward
and backward or lifting the front
portion of the seat. If the green
mark is invisible and the seat
moves, it is not locked properly.

5.Pull up the seatback recline strap.
6.Lift and push the seatback back-

ward firmly until it clicks into place.
Make sure the seatback is locked
in place.

7.Return the seat belt to the proper

position.

OYP034228N

OYP034225N

OYP034232N

3 25

Safety features of your vehicle

If the rear catches of the seat are
locked into the rear anchors (2) while
the front catches are not locked into
the front anchors (1), do the follow-
ings to release the rear catches from
the rear anchors.

Pull the removal strap and lift the
rear portion of the seat cushion.
Then the rear catches will be released.
Remove the seat while lifting up the
rear portion of seat cushion and then
reinstalling the tumble seat.

WARNING -

Installing or

removing the tumble seat

Do not install or remove the
tumble (2nd row center) seat, if
there are occupants in the 3rd
row seats, as this may injure
occupants.

OYP034233N

OYP034235N

OYP034223N

Safety features of your vehicle

26

3

Stowing the rear seat
- 3rd row seat

The rear seat can be folded and
stowed in the luggage compartment
to provide additional cargo space.

To stow the rear seat:
1. Lower the headrest to the lowest

position. To stow easily, adjust the
seatback to upright position. (if
necessary)

2. Pull up the seat by using the stow-

ing lever.

3. Stow the seat by pushing down

firmly.

OYP034240N

OYP037241

OYP034242N

3 27

Safety features of your vehicle

Make sure there is no body or object
around the seat and be careful not to
injure your hands or body under the
seat or in the moving parts when
stowing or reinstalling the seat.

To use the rear seat:
1. Lift the seat by pulling up the stow-

ing lever.

CAUTION

- To stow 3rd

row seat

Do not stow the 3rd row seat
when the seat back is folded
down. It may damage the 3rd
seat mechanism.

OYP037304

OYP037286