KIA Sorento (2018 year). Manual — part 23

Driving your vehicle

32

5

To release EPB (electronic parking
brake) automatically:

• Shift lever in P (Park)

With the engine running depress
the brake pedal and shift out of P
(Park) to R (Reverse) or D (Drive).

• Shift lever in N (Neutral)

With the engine running depress
the brake pedal and shift out of N
(Neutral) to R (Reverse) or D
(Drive).

• Automatic transaxle vehicle

1. Start the engine.
2. Fasten the driver's seat belt.
3. Close the driver's door, engine

hood and trunk.

4. Depress the accelerator pedal

while the shift lever is in R
(Rear), D (Drive) or Sports
mode.

Make sure the brake warning light
goes off.

✽

✽

NOTICE

• For your safety, you can engage

the EPB even though the ignition
switch or engine stop/start button
is in the OFF position, but you
cannot release it.

• For your safety, depress the brake

pedal and release the parking
brake manually with the EPB
switch when you drive downhill or
when backing up the vehicle.

Do not follow the above procedure
when driving on a flat level ground.
The vehicle may suddenly move for-
ward.

CAUTION

• If the parking brake warning

light is still on even though
the EPB has been released,
have the system checked by
an authorized Kia dealer.

• Do not drive your vehicle with

the EPB applied. It may cause
excessive brake pad and
brake rotor wear.

UM USA 5.QXP 3/6/2017 1:35 PM Page 32

5 33

Driving your vehicle

EPB (electronic parking brake) may
be automatically applied when:

• The EPB is overheated
• Requested by other systems

✽

✽

NOTICE

If the driver turns the engine off by
mistake while Auto Hold is operat-
ing, EPB will be automatically
applied. (Vehicles equipped with
Auto Hold)

System warning

• If you try to drive off depressing the

accelerator pedal with the EPB
applied, but the EPB doesn't
release automatically, a warning
will sound and a message will
appear.

• If the driver's seat belt is not fas-

tened and the engine hood, driver's
door or trunk is opened, a warning
will sound and a message will
appear.

• If there is a problem with the vehi-

cle, a warning may sound and a
message may appear.

If the above situation occurs, depress
the brake pedal and release EPB by
pressing the EPB switch.

OUM054104L

WARNING

- Parking

Brake Use

All vehicles should always have
the parking brake fully engaged
when parked to avoid inadver-
tent movement of the car which
can injure occupants or pedes-
trians.

UM USA 5.QXP 3/6/2017 1:35 PM Page 33

Driving your vehicle

34

5

• A click or electric brake motor

whine sound may be heard while
operating or releasing the EPB, but
these conditions are normal and
indicate that the EPB is functioning
properly.

• When leaving your keys with a

parking lot attendant or valet, make
sure to inform him/her how to oper-
ate the EPB.

• The EPB may malfunction if you

drive with the EPB applied.

• When you automatically release

EPB by depressing the accelerator
pedal, depress it slowly.

System warning

When the conversion from Auto Hold
to EPB is not working properly a
warning will sound and a message
will appear.

✽

✽

NOTICE

Depress the brake pedal when the
above message appears for the Auto
Hold and EPB may not activate.

OUM054100L

OUM054101L

■

Type A

■

Type B

UM USA 5.QXP 3/6/2017 1:35 PM Page 34

5 35

Driving your vehicle

System warning

If the EPB is applied while Auto Hold
is activated because of ESC
(Electronic Stability Control) signal, a
warning will sound and a message
will appear.

EPB malfunction indicator
(if equipped)

This warning light illuminates if the
engine start/stop button is changed
to the ON position and goes off in
approximately 3 seconds if the sys-
tem is operation normally.
If the EPB malfunction indicator
remains on, comes on while driving,
or does not come on when the igni-
tion switch or the engine start/stop
button is changed to the ON position,
this indicates that the EPB may have
malfunctioned.

If this occurs, have your vehicle
checked by an authorized Kia dealer
as soon as possible.
The EPB malfunction indicator may
illuminate when the ESC indicator
comes on to indicate that the ESC is
not working properly, but it does not
indicate a malfunction of the EPB.

OUM054106

■

Type A

■

Type B

OUM054102L

OUM054103L

■

Type A

■

Type B

UM USA 5.QXP 3/6/2017 1:35 PM Page 35

Driving your vehicle

36

5

• The EPB warning light may illumi-

nate if the EPB switch operates
abnormally. Shut the engine off
and turn it on again after a few min-
utes. The warning light will go off
and the EPB switch will operate
normally. However, if the EPB
warning light is still on, have the
system checked by an authorized
Kia dealer.

• If the parking brake warning light

does not illuminate or blinks even
though the EPB switch was pulled
up, the EPB is not applied.

• If the parking brake warning light

blinks when the EPB warning light
is on, press the switch, then pull it
up. Once more press it back to its
original position and pull it back up.
If the EPB warning does not go off,
have the system checked by an
authorized Kia dealer.

Emergency braking

If there is a problem with the brake
pedal while driving, emergency brak-
ing is possible by pulling up and
holding the EPB switch. Braking is
possible only while you are holding
the EPB switch.

✽

✽

NOTICE

During emergency braking by the
EPB, the parking brake warning
light will illuminate to indicate that
the system is operating.

If you notice a continuous noise or
burning smell when the EPB is used
for emergency braking, have your
vehicle checked by an authorized Kia
dealer.

When the EPB (electronic parking
brake) is not released

If the EPB does not release normal-
ly, take your vehicle to an authorized
Kia dealer by loading the vehicle on
a flatbed tow truck and have the sys-
tem checked.

WARNING

Do not operate the electronic
parking brake while the vehicle
is moving except in an emer-
gency situation. Applying the
electronic parking brake while
the vehicle is moving at normal
speeds can cause a sudden
loss of control of the vehicle. If
you must use the electronic
parking brake to stop the vehi-
cle, use great caution in apply-
ing the brake.

UM USA 5.QXP 3/6/2017 1:35 PM Page 36

5 37

Driving your vehicle

AUTO HOLD (if equipped)

The Auto Hold maintains the vehicle
in a standstill even though the brake
pedal is not depressed after the driv-
er brings the vehicle to a complete
stop by depressing the brake pedal.

1.Depress the brake pedal, start the

engine and then press the Auto
Hold button.

The white AUTO

HOLD indicator will come on indi-
cating the system is in standby.
Before the Auto Hold will engage,
the driver's door, engine hood and
trunk must be closed and the dri-
ver's seat belt must be fastened.

2.When coming to a complete stop

by depressing the brake pedal, the
AUTO HOLD indicator changes
from white to green indicating the
AUTO HOLD is engaged and EPB
is applied. The vehicle will remain
at a standstill even if you release
the brake pedal.

3.If EPB is applied, Auto Hold will be

released.

OUMA054016

W

W

W

W

h

h

h

h

ii

ii

tt

tt

e

e

e

e

OUM054017

W

W

W

W

h

h

h

h

ii

ii

tt

tt

e

e

e

e

G

G

G

G

rr

rr

e

e

e

e

e

e

e

e

n

n

n

n

UM USA 5.QXP 3/6/2017 1:35 PM Page 37

Driving your vehicle

38

5

4.If you press the accelerator pedal

with the shift lever in R (Reverse),
D (Drive) or sports mode, the Auto
Hold will be released automatically
and the vehicle will start to move.
The indicator changes from green
to white indicating the Auto Hold is
in standby and the EPB is
released.

When driving off from Auto Hold by
depressing the accelerator pedal,
always check the surrounding area
near your vehicle.
Slowly depress the accelerator pedal
for a smooth launch.

Cancel

To cancel the Auto Hold operation,
press the Auto Hold switch. The
AUTO HOLD indicator will go out.
To cancel the Auto Hold operation
when the vehicle is at a standstill,
press the Auto Hold switch while
depressing the brake pedal.

✽

✽

NOTICE

• The following are conditions when

the Auto Hold will not engage
(Auto Hold light will not turn
green and the Auto Hold system
remains in stand by):
- The driver's seat belt is unfas-

tened and driver's door is opened

- The engine hood is opened
- The trunk is opened
- The shift lever is in P (Park)
- The EPB is applied

• For your safety, the Auto Hold

automatically switches to EPB
under any of the following condi-
tions (Auto Hold light remains
white and the EPB automatically
applies):
- The driver's seat belt is unfas-

tened and driver's door is opened

- The engine hood is opened
- The trunk is opened
- The vehicle is in a standstill for

more than 10 minutes

- The vehicle is standing on a steep

slope

- The vehicle moved several times

(Continued)

OUMA054018

L

L

L

L

ii

ii

g

g

g

g

h

h

h

h

tt

tt

o

o

o

o

ff

ff

ff

ff

UM USA 5.QXP 3/6/2017 1:35 PM Page 38

5 39

Driving your vehicle

(Continued)

In these cases, the brake warning
light comes on, the AUTO HOLD
indicator changes from green to
white, and a warning sounds and a
message will appear to inform you
that EPB has been automatically
engaged. Before driving off again,
press foot brake pedal, check the
surrounding area near your vehi-
cle and release parking brake
manually with the EPB switch.

• If the AUTO HOLD indicator

lights up yellow, the Auto Hold is
not working properly. Take your
vehicle to an authorized Kia deal-
er and have the system checked.

If there is a malfunction with the dri-
ver’s door, engine hood or trunk open
detection system, the Auto Hold may
not work properly.
Take your vehicle to an authorized Kia
dealer and have the system checked.

✽

✽

NOTICE

A click or electric brake motor
whine sound may be heard while
operating or releasing the EPB, but
these conditions are normal and
indicate that the EPB is functioning
properly.

WARNING

To reduce the risk of an acci-
dent, do not activate Auto Hold
while driving downhill, backing
up or parking your vehicle.

UM USA 5.QXP 3/6/2017 1:35 PM Page 39

Driving your vehicle

40

5

Anti-lock brake system (ABS)

ABS (or ESC) will not prevent acci-
dents due to improper or dangerous
driving maneuvers. Even though
vehicle control is improved during
emergency braking, always maintain
a safe distance between you and
objects ahead.

Vehicle speeds

should always be reduced during
extreme road conditions. The vehicle
should be driven at reduced speeds
in the following circumstances:
• When driving on rough, gravel or

snow-covered roads

• When driving with tire chains

installed

• When driving on roads where the

road surface is pitted or has differ-
ent surface heights.

Driving in these conditions increase
the stopping distance for your vehi-
cle.

The ABS continuously senses the
speed of the wheels. If the wheels
are going to lock, the ABS system
repeatedly modulates the hydraulic
brake pressure to the wheels.
When you apply your brakes under
conditions which may lock the
wheels, you may hear a “tik-tik’’
sound from the brakes, or feel a cor-
responding sensation in the brake
pedal. This is normal and it means
your ABS is active.
In order to obtain the maximum ben-
efit from your ABS in an emergency
situation, do not attempt to modulate
your brake pressure and do not try to
pump your brakes. Press your brake
pedal as hard as possible or as hard
as the situation allows the ABS to
control the force being delivered to
the brakes.

✽

✽

NOTICE

A click sound may be heard in the
engine compartment when the vehi-
cle begins to move after the engine is
started. These conditions are normal
and indicate that the anti-lock brake
system is functioning properly.

UM USA 5.QXP 3/6/2017 1:35 PM Page 40

5 41

Driving your vehicle

• Even with the anti-lock brake sys-

tem, your vehicle still requires suf-
ficient stopping distance. Always
maintain a safe distance from the
vehicle in front of you.

• Always slow down when cornering.

The anti-lock brake system cannot
prevent accidents resulting from
excessive speeds.

• On loose or uneven road surfaces,

operation of the anti-lock brake
system may result in a longer stop-
ping distance than for vehicles
equipped with a conventional
brake system.

The ABS warning light will stay on for
approximately 3 seconds after the
ignition switch is ON. During that
time, the ABS will go through self-
diagnosis and the light will go off if
everything is normal. If the light stays
on, you may have a problem with
your ABS. Contact an authorized Kia
dealer as soon as possible.

• When you drive on a road having

poor traction, such as an icy road,
and have operated your brakes
continuously, the ABS will be active
continuously and the ABS warning
light may illuminate. Pull your vehi-
cle over to a safe place and stop
the engine.

• Restart the engine. If the ABS

warning light goes off, then your
ABS system is normal. Otherwise,
you may have a problem with the
ABS. Contact an authorized Kia
dealer as soon as possible.

✽

✽

NOTICE

When you jump start your vehicle
because of a drained battery, the
engine may not run as smoothly and
the ABS warning light may turn on
at the same time. This happens
because of low battery voltage. It
does not mean your ABS has mal-
functioned.
• Do not pump your brakes!
• Have the battery recharged before

driving the vehicle.

W-78

UM USA 5.QXP 3/6/2017 1:35 PM Page 41

Driving your vehicle

42

5

Electronic stability control
(ESC)

The Electronic Stability control
(ESC) system is designed to stabi-
lize the vehicle during cornering
maneuvers. ESC checks where you
are steering and where the vehicle is
actually going. ESC applies the
brakes on individual wheels and
intervenes with the engine manage-
ment system to stabilize the vehicle.

Electronic stability control (ESC) will
not prevent accidents. Excessive
speed in turns, abrupt maneuvers
and hydroplaning on wet surfaces
can still result in serious accidents.
Only a safe and attentive driver can
prevent accidents by avoiding
maneuvers that cause the vehicle to
lose traction.

Even with ESC

installed, always follow all the normal
precautions for driving - including
driving at safe speeds for the condi-
tions.

The Electronic Stability Control (ESC)
system is an electronic system
designed to help the driver maintain
vehicle control under adverse condi-
tions. It is not a substitute for safe driv-
ing practices. Factors including speed,
road conditions and driver steering
input can all affect whether ESC will be
effective in preventing a loss of control.
It is still your responsibility to drive and
corner at reasonable speeds and to
leave a sufficient margin of safety.
When you apply your brakes under
conditions which may lock the wheels,
you may hear a “tik-tik’’ sound from the
brakes, or feel a corresponding sensa-
tion in the brake pedal. This is normal
and it means your ESC is active.

✽

✽

NOTICE

A click sound may be heard in the
engine compartment when the vehi-
cle begins to move after the engine is
started. These conditions are normal
and indicate that the Electronic
Stability Control System is function-
ing properly.

OUMA054019

UM USA 5.QXP 3/6/2017 1:35 PM Page 42

5 43

Driving your vehicle

ESC operation

ESC ON condition

• When the ignition is turned

ON, ESC and ESC OFF
indicator lights illuminate for
approximately 3 seconds,
then ESC is turned on.

• Press the ESC OFF but-

ton for at least half a sec-
ond after turning the igni-
tion ON to turn ESC off.
(ESC OFF indicator will
illuminate). To turn the
ESC on, press the ESC
OFF button (ESC OFF
indicator light will go off).

• When starting the engine,

you may hear a slight tick-
ing sound. This is the ESC
performing an automatic
system self-check and does
not indicate a problem.

When operating

When the ESC is in opera-
tion, the ESC indicator light
blinks.
•

When the Electronic

Stability Control is operat-
ing properly, you can feel a
slight pulsation in the vehi-
cle. This is only the effect
of brake control and indi-
cates nothing unusual.

• When moving out of the

mud or driving on a slip-
pery road, pressing the
accelerator pedal may not
cause the engine rpm
(revolutions per minute) to
increase.

ESC operation off

ESC OFF state

This car has 2 kinds of ESC
off states.
If the engine stops when
ESC is off, ESC remains off.
Upon restarting the engine,
the ESC will automatically
turn on again.

-

UM USA 5.QXP 3/6/2017 1:35 PM Page 43

Driving your vehicle

44

5

• ESC off state 1
To cancel ESC operation, press the
ESC OFF button (ESC OFF

)

shortly (ESC OFF indicator light
(ESC OFF

) illuminates). At this

state, the engine control function
does not operate. It means the trac-
tion control function does not oper-
ate. Brake control function only oper-
ates.

• ESC off state 2
To cancel ESC operation, press the
ESC OFF button (ESC OFF

) for

more than 3 seconds. ESC OFF indi-
cator light (ESC OFF

) illuminates

and ESC OFF warning chime will
sound. At this state, the engine con-
trol function and brake control func-
tion do not operate. It means the car
stability control function does not
operate any more.

Indicator light

When ignition switch is turned to ON,
the indicator light illuminates, then
goes off if the ESC system is operat-
ing normally.
The ESC indicator light blinks when-
ever ESC is operating or illuminates
when ESC fails to operate.
The ESC OFF indicator light comes
on when the ESC is turned off with
the button.

OUM054165L

OUM054161L

■

Type A

■

Type B

OUM054162L

OUM054163L

■

Type A

■

Type B

■

ESC indicator light

■

ESC OFF indicator light

UM USA 5.QXP 3/6/2017 1:35 PM Page 44

5 45

Driving your vehicle

ESC OFF usage

When driving

• ESC should be turned on for daily

driving whenever possible.

• To turn ESC off while driving, press

the ESC OFF button while driving
on a flat road surface.

✽

✽

NOTICE

• When operating the vehicle on a

dynamometer, ensure that the
ESC is turned off (ESC OFF light
illuminated). If the ESC is left on,
it may prevent the vehicle speed
from increasing, and result in false
diagnosis.

• Turning the ESC off does not

affect ABS or brake system opera-
tion.

WARNING

- Operating

ESC

Never press the ESC OFF but-
ton while ESC is operating (ESC
indicator light blinks).
If ESC is turned off while ESC is
operating, the vehicle may slip
out of control.

WARNING

- Electronic sta-

bility control

Drive carefully even though
your vehicle has Electronic
Stability Control. It can only
assist you in maintaining con-
trol under certain circum-
stances.

UM USA 5.QXP 3/6/2017 1:35 PM Page 45

Driving your vehicle

46

5

Vehicle stability management
(VSM)

This system provides further
enhancements to vehicle stability
and steering responses when a vehi-
cle is driving on a slippery road or a
vehicle detects changes in coeffi-
cient of friction between right wheels
and left wheels when braking.

VSM operation

When the VSM is in operation, ESC
indicator light (

) blinks.

When the vehicle stability manage-
ment is operating properly, you can
feel a slight pulsation in the vehicle
and/or abnormal steering responses
(EPS). This is only the effect of brake
and EPS control and indicates noth-
ing unusual.

The VSM does not operate when:

• Driving on bank road such as gra-

dient or incline

• Driving in reverse
• ESC OFF indicator light (

)

remains on the instrument cluster

• EPS indicator light remains on the

instrument cluster

VSM operation off

If you press the ESC OFF button to
turn off the ESC, the VSM will also
cancel and the ESC OFF indicator
light (

) illuminates.

To turn on the VSM, press the button
again. The ESC OFF indicator light
goes out.

WARNING

- Tire/

Wheel size

When replacing tires and wheels,
make sure they are the same size
as the original tires and wheels
installed. Driving with varying
tire or wheel sizes may diminish
any supplemental safety benefits
of the VSM system.

UM USA 5.QXP 3/6/2017 1:35 PM Page 46

5 47

Driving your vehicle

Malfunction indicator

The VSM can be deactivated even if
you don’t cancel the VSM operation
by pressing the ESC OFF button. It
indicates that a malfunction has
been detected somewhere in the
Electric Power Steering system or
VSM system. If the ESC indicator
light (

) or EPS warning light

remains on, take your vehicle to an
authorized Kia dealer and have the
system checked.

✽

✽

NOTICE

• The VSM is designed to function

above approximately 13 mph (22
km/h) on curves.

• The VSM is designed to function

above approximately 6 mph (10
km/h) when a vehicle is braking on
a split-mu road. The split-mu road
is made of surfaces which have dif-
ferent friction forces.

• The Vehicle Stability Management

system is not a substitute for safe
driving practices but a supplemen-
tary function only. It is the respon-
sibility of the driver to always check
the speed and the distance to the
vehicle ahead. Always hold the
steering wheel firmly while driving.

• Your vehicle is designed to activate

according to the driver’s intention,
even with installed VSM. Always
follow all the normal precautions
for driving at safe speeds for the
conditions – including driving in
clement weather and on a slippery
road.

Hill-start assist control (HAC)

A vehicle has the tendency to roll
back on a steep hill when it starts to
go after stopping. The Hill-start
Assist Control (HAC) prevents the
vehicle from rolling back by applying
the brakes automatically for about 2
seconds. The brakes are released
when the accelerator pedal is
depressed or after about 2 seconds.
The HAC is activated only for about 2
seconds, so when the vehicle is
starting off always depress the accel-
erator pedal.

WARNING

- Maintaining

Brake Pressure on Incline

HAC does not replace the need
to apply brakes while stopped
on an incline. While stopped,
make sure you maintain brake
pressure sufficient to prevent
your vehicle from rolling back-
ward and causing an accident.
Don’t release the brake pedal
until you are ready to accelerate
forward.

UM USA 5.QXP 3/6/2017 1:35 PM Page 47