KIA Sorento (2018 year). Manual — part 26

Driving your vehicle

- After an engine start, please stop

for several seconds. If system ini-
tialization is not completed, the
ASCC does not normally operate.

- After an engine start, if any objects

are not detected or the sensor
cover is obscured with foreign sub-
stances, there is a possibility that
the ASCC system may not work.

- Below conditions may cause mal-

function: over baggage loading in a
trunk, suspension remodeling, tire
replacement with unauthorized
tires or tires with different worn-out
and pressure levels.

This device complies with Part 15
of the FCC rules.
Operation is subject to the following
three conditions:
1. This device may not cause harm-

ful interference, and

2. This device must accept any inter-

ference received, including inter-
ference that may cause undesired
operation.

3. Changes or modifications not

expressly approved by the party
responsible for compliance could
void the user’s authority to operate
the device.

Radio frequency radiation expo-
sure information:
This equipment complies with FCC
radiation exposure limits set forth for
an uncontrolled environment.
This equipment should be installed
and operated with minimum distance
of 20 cm between the radiator
(antenna) and your body.
This transmitter must not be co-
located or operating in conjunction
with any other antenna or transmit-
ter.

WARNING

- Inclines &

Towing

Do not use ASCC on steep
inclines or when towing another
vehicle or trailer since such
extreme loading can interfere
with your vehicle's ability to
maintain the selected speed.

UM USA 5.QXP 3/6/2017 1:38 PM Page 80

5 81

Driving your vehicle

DRIVE mode

The drive mode may be selected
according to the driver’s preference
or road condition.

The mode changes whenever the
DRIVE MODE button is pressed.

❈

When normal mode is selected, it
is not displayed on the cluster.

ECO mode (Active ECO)

Active ECO helps improve
fuel efficiency by control-
ling certain engine and
transaxle system operat-
ing parameters. Fuel effi-
ciency depends on the
driver's driving habit and
road condition.
• When the DRIVE MODE

button is pressed and
the ECO mode is select-
ed, the ECO indicator
(green) will illuminate to
show that the Active
ECO is operating.

• When the Active ECO is

activated, it does not
turn off even though the
engine is restarted
again. To turn off the
system, press the
DRIVE MODE button
again.

DRIVE MODE INTEGRATED CONTROL SYSTEM

OUMA054036

■

Type A

■

Type B

OUMA054037

NORMAL

SPORT ECO

ECO

UM USA 5.QXP 3/6/2017 1:38 PM Page 81

Driving your vehicle

When Active ECO is activated:
• The acceleration may slightly be

reduced even though you depress
the accelerator fully.

• The air conditioner performance

may be limited

• The shift pattern of the automatic

transaxle may change.

• The engine noise may get louder.

The above situations are normal
conditions when the Active Eco
System is activated to improve fuel
efficiency.

Limitation of Active ECO opera-
tion:
If the following conditions occur while
Active ECO is operating, the system
operation is limited even though
there is no change in the ECO indi-
cator.
• When the coolant temperature is

low:
The system will be limited until
engine performance becomes nor-
mal.

• When driving up a hill:

The system will be limited to gain
power when driving uphill because
the engine torque is restricted.

• When using manual mode:

The system will be limited accord-
ing to the shift location.

• When the accelerator pedal is

deeply depressed for a few sec-
onds:
The system will be limited, judging
that the driver wants to speed up.

SPORT mode

SPORT mode focuses on
dynamic driving by auto-
matically adjusting the
steering wheel, engine
and transaxle system.
• When the DRIVE MODE

button is pressed and
the SPORT mode is
selected, the SPORT
indicator (yellow) will illu-
minate.

• When the SPORT mode

is activated, and the
engine start/stop button
is turned off and on it will
change to NORMAL
mode. To turn on the
SPORT mode press
DRIVE MODE button
again.

SPORT

UM USA 5.QXP 3/6/2017 1:38 PM Page 82

5 83

Driving your vehicle

• If the system is activat-

ed:

- While holding vehicle

speed, it maintains the
gear and RPM for some
time even though the
accelerator pedal is not
depressed.

- Up-shifting is delayed.

✽

NOTICE

In Sport drive mode, the fuel effi-
ciency may decrease.

UM USA 5.QXP 3/6/2017 1:38 PM Page 83

Driving your vehicle

The Blind Spot Detection System
(BSD) uses a radar sensor to alert
the driver.
It senses the rear side territory of the
vehicle and provides and indication
to the driver.

(1) BSD (Blind Spot Detection)

The warning range depends on

your vehicle speed. However, if
your vehicle is about 6 mph (10
km/h) faster than the other vehi-
cle, the system will not warn you.

(2) LCA (Lane Change Assist)

When a vehicle approaches you

at high speed, the system will
warn you.

(3) RCTA (Rear Cross Traffic Alert)

When your vehicle moves rear-

ward, and the sensor detects an
approaching vehicle in the left or
right side, the system will warn
you.

BLIND SPOT DETECTION SYSTEM (BSD) (IF EQUIPPED)

WARNING

- BSD

Limitations

• The Blind Spot Detection

System (BSD) is a supplemen-
tal system. Do not solely rely
on the system and always pay
attention to drive safely.

• The Blind Spot Detection

System may not detect every
object alongside the vehicle
and is not a substitute for
proper and safe lane chang-
ing procedures. Always drive
safely and use caution when
changing lanes.

OUM054176L

UM USA 5.QXP 3/6/2017 1:38 PM Page 84

5 85

Driving your vehicle

BSD (Blind Spot Detection) /
LCA (Lane Change Assist)

Operating conditions

The indicator on the switch will illumi-
nate when the Blind Spot Detection
System (BSD) switch is pressed with
the Engine Start/Stop Button ON.
If vehicle speed exceeds 18.6 mph
(30 km/h), the system will activate.
If you press the switch again, the
switch indicator and system will be
turned off.
If the ignition switch is turned OFF
and ON the system returns to the
previous state.

When the system is not used turn the
system off by turning off the switch.
When the system is turned on the
warning light will illuminate for 3 sec-
onds on the outside rearview mirror.

Warning type

The system will activate when:
1.The system is on.
2.Vehicle speed is above 18.6 mph

(30 km/h).

3.Other vehicles are detected in the

rear side.

WARNING

The Blind Spot Detection
System with Lane Change
Assist and Rear Cross Traffic
Alert is not a substitute for
proper and safe lane changing
procedures. Always drive safely
and use caution when changing
lanes. The Blind Spot Detection
System may not detect every
object alongside the vehicle.

OUMA054027

UM USA 5.QXP 3/6/2017 1:38 PM Page 85

Driving your vehicle

If a vehicle is detected within the
boundary of the system, a warning
light will illuminate on the outside
rearview mirror.
If the detected vehicle is not in
detecting range, the warning will turn
off according to driving conditions.

The second stage alarm will activate
when:
1.The first stage alert is on
2.The turn signal is on to change a

lane

When the second stage alert is acti-
vated, a warning light will blink on the
outside rearview mirror and an alarm
will sound.
If you move the turn signal switch to
the original position, the second
stage alert will be deactivated.

- The second stage alarm may be

deactivated.

• To activate the alarm:

Go to the User Settings Mode

→

Sound and select "BSD" on the
LCD display.

• To deactivate the alarm:

Go to the User Settings Mode

→

Sound and deselect "BSD" on the
LCD display.

✽

NOTICE

The alarm function helps alert the
driver. Deactivate this function only
when it is necessary

OUM054029

2nd stage

OUM054028

1st stage

UM USA 5.QXP 3/6/2017 1:38 PM Page 86

5 87

Driving your vehicle

Detecting sensor

The sensors are located inside of the
rear bumper.
Always keep the rear bumper clean
for the system to work properly.

Warning message

The message will appear to notify
the driver if there are foreign sub-
stances on the rear bumper or it is
hot near the rear bumper. The light
on the switch and the system will
turn off automatically.

Remove the foreign substance on
the rear bumper.
After the foreign substance is
removed, if you drive for approxi-
mately 10 minutes, the system will
work normally.
If the system does not work normally
even though the foreign substance is
removed, take your vehicle to an
authorized Kia dealer and have the
system checked.

OUM054030

OUMA057228

■

Type A

■

Type B

OUMA057227

UM USA 5.QXP 3/6/2017 1:38 PM Page 87

Driving your vehicle

If the system does not work properly,
a warning message will appear and
the light on the switch will turn off. The
system will turn off automatically.

Have your vehicle inspected by an
authorized Kia dealer.

RCTA (Rear Cross Traffic Alert)

When your vehicle moves backwards
from a parking position, the sensor
detects approaching vehicles to the
left or right side direction and gives
information to the driver.

Operating conditions

• Select RCTA (Rear Cross Traffic

Alert) in "User Settings" under
"Driving Assist" on the instrument
cluster. The system will turn on and
standby to activate.

• Select RCTA again, to turn the sys-

tem off.

• If the vehicle is turned off and on

again, the RCTA system will return
to the state right before the vehicle
was turned off. Always turn the
RCTA system off when not in use.

OUM054178L

OYP054026K

OUM054124L

UM USA 5.QXP 3/6/2017 1:38 PM Page 88

5 89

Driving your vehicle

• The system operates when the

vehicle speed is below 6.2 mph (10
km/h) with the shift lever in R
(Reverse).

• The RCTA (Rear Cross Traffic

Alert) detecting range is 0.5m ~
20m based on the side direction. If
the approaching vehicle speed is
2.5 mph (4 km/h) ~ 22 mph (36
km/h) within sensing range, it is
detected. However, the system
sensing range is different based on
conditions. Always pay attention to
your surroundings.

Warning type

• If the vehicle detected by sensors

approaches your vehicle, the warn-
ing chime will sound and the warn-
ing light will blink on the outside
rearview mirror.

• If the detected vehicle is out of the

sensing range of your vehicle,
move the vehicle away from the
detected object slowly; the warning
will be cancelled.

• The system may not operate prop-

erly due to other factors or circum-
stances. Always pay attention to
your surroundings.

❈

If your vehicle's left or right side
bumper is blinded by barrier or
vehicles, the system sensing abili-
ty may be deteriorated.

OYP054027K

WARNING

UM USA 5.QXP 3/6/2017 1:38 PM Page 89

Driving your vehicle

✽

NOTICE

• The system may not work proper-

ly if the bumper has been replaced
or if a repair work has been done
near the sensor.

• The detection area differs accord-

ing to the roads width. If the road
is narrow the system may detect
other vehicles in the next lane.

• On the contrary, if the road is very

wide the system may not detect
other vehicles.

• The system may turn off due to

strong electromagnetic waves.

Non-operating condition

Driver's Attention

The driver must be cautious in the
below situations for the system may
not assist the driver and may not
work properly.

- Curved roads, tollgates, etc.
- The sensor cover is obscured by

rain, snow, mud, etc

- The rear bumper near the sensor is

covered or hidden with a foreign
matter such as a sticker, bumper
guard, bicycle stand etc.

- The rear bumper is damaged or the

sensor is out of place.

- The height of the vehicle has signif-

icantly changed such as when the
trunk is loaded with heavy objects,
abnormal tire pressure etc.

- Due to bad weather such as heavy

rain or snow.

- A fixed object is near such as a

guardrail, etc.

- A substantial amount of metallic

objects such as a construction
area.

- A large vehicle is nearby such as a

bus or truck.

- A motorcycle or bicycle is near.
- A flat trailer is near.
- If the vehicle starts at the same

time as the vehicle next to it and
has accelerated.

- When the other vehicle passes by

at a high rate of speed.

- When changing lanes.
- When going down or up a steep,

uneven road.

- When the other vehicle drives at

the rear very nearby or drives very
close.

- When a trailer or carrier is installed.

UM USA 5.QXP 3/6/2017 1:38 PM Page 90

5 91

Driving your vehicle

- When the temperature of the rear

bumper is very high or low.

- When parking structure covers the

sensor.

- When reversing from a parking

space with pillars or metal struc-
tures.

- When you are reversing and if the

detected vehicle is simultaneously
reversing.

- If there are small objects like shop-

ping carts and baby carriages.

- If there is a vehicle with decreased

ride height (lowered).

- When the vehicle is close to anoth-

er vehicle.

- When driving through a narrow

road with many plants.

- When driving on wet surface.

Outside rearview mirror may not
alert the driver when:

- The outside rearview mirror hous-

ing is obscured by mud, snow, etc.

- The window is obscured by mud,

snow, etc.

- The windows are overly tinted.

This device complies with Part 15
of the FCC rules.
Operation is subject to the following
two conditions:
1. This device may not cause harm-

ful interference, and

2. This device must accept any inter-

ference received, including inter-
ference that may cause undesired
operation.

UM USA 5.QXP 3/6/2017 1:38 PM Page 91

Driving your vehicle

LANE DEPARTURE WARNING SYSTEM (LDWS) (IF EQUIPPED)

Lane Departure Warning System
detects the lane with a front view
camera at the front windshield and
warns you when your vehicle departs
from the lane.

OUM054032

OUM054149

WARNING

• Driver is responsible for being

aware of surroundings and
steering the vehicle for safe
driving practices.

• The LDWS does not make the

vehicle change lanes or stay
in the lane.

• Do not turn the steering wheel

suddenly if the LDWS warns
that your vehicle is leaving the
lane.

• If the a front view camera can-

not detect the lane or if the
vehicle speed does not
exceed 40 mph (64 kph), the
LDWS will not be able to noti-
fy you if the vehicle leaves the
lane.

(Continued)

(Continued)
• Do not disassemble a front

view camera temporarily for
tinted window or attaching
any types of coatings and
accesorsories. If you disas-
semble the camera and
assemble it again, take your
vehicle to an authorized Kia
dealer and have the system
checked to need a calibration.

• When you replace the wind-

shield glass or front view
camera, take your vehicle to
an authorized Kia dealer and
have the system checked to
need a calibration.

• Do not allow any water or liq-

uid to contact the front view
camera. If not, the camera
may be damaged.

• Do not remove the LDWS

parts and do not damage the
camera by a strong impact.

(Continued)

UM USA 5.QXP 3/6/2017 1:38 PM Page 92

5 93

Driving your vehicle

LDWS operation

To activate/deactivate the LDWS:
With the ignition switch in the ON
position, press the LDWS button
located on the instrument panel on
the lower left hand side of the driver.

The indicator in the cluster display
will initially illuminate white.

If the

indicator(white) activated in the pre-
vious ignition cycle, the system turns
on without any control. If you press
the LDWS button again, the indicator
on the cluster display will go off. The
color of indicator will change depend
on the condition of LDWS.
- White : Sensor does not detect the

lane marker or vehicle
speed is less than 40mph
(64kph).

- Green : Sensor detects the lane

marker.

(Continued)
• Do not put objects that reflect

light on the crash pad.

• You may not hear warning

sound of LDWS because of
the excessive audio sound.

OUMA054031

OUM054133L

UM USA 5.QXP 3/7/2017 5:43 PM Page 93

Driving your vehicle

If the vehicle leaves the lane when
the LDWS operates and vehicle
speed exceeds 40 mph (64 kph), the
warning is issued as follows :

1. Visual warning
If the vehicle leaves the lane, the
lane marker indicator of leaving
direction and the warning indicator
on the LCD display blinks less than 3
seconds.

2. Audible warning
If the vehicle leaves the lane, the
warning sound is provided less than
3 seconds.

OUM054126L

OUM054127L

■

When the sensor detects the lane line

■

When the sensor doesn’t detect the lane line

OUM054128L

OUM054129L

■

Left lane departure warning

■

Right lane departure warning

UM USA 5.QXP 3/6/2017 1:39 PM Page 94

5 95

Driving your vehicle

Warning light and message

Check LDWS

LDWS failure indicator

The LDWS failure indicator(yellow)
will illuminate if the LDWS is not
working properly. We recommend
you to have your vehicle checked by
an authorized Kia dealer.

The LDWS does not operate
when:

• The driver turns on the turn signal

to change lanes or operates the
hazard warning flasher.

• Driving on the lane marker.

❈

Always operate the turn signal
before changing lanes.

DRIVER'S ATTENTION

The LDWS may not warn you even if
the vehicle leaves the lane, or may
warn you even if the vehicle does not
leave the lane when recognition of
the lane marker is poor or limited :

❖

When lane and road condition is
poor

- It is difficult to distinguish the lane

marker from road when the lane
marker is covered with dust, sand
or other factors.

- It is difficult to distinguish the color

of the lane marker from road.

- There is something looks like a

lane marker.

- The lane marker is indistinct or

damaged.

- The number of lanes increases/

decreases or the lane lines are
crossing (Driving through a toll
plaza/toll gate, merged/divided
lane).

- There are more than two lane

markers.

- The lane marker is very thick or

thin.

OUM054158L

UM USA 5.QXP 3/6/2017 1:39 PM Page 95

Была ли эта страница вам полезна?

Да!Нет

KIA Sorento (2018 year). Manual — part 26

Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.