DongFeng RICH. Instruction — part 4
Pre-driving checks and adjustments 2-15
SEAT BELTS
Precautions on seat belt usage
Zhengzhou NISSAN strongly
encourages you and all of your
passengers to buckle up every
time you drive.
Your chances of being injured in
an accident and the severity of
injury may be greatly reduce if
you are wearing your seat belt
and it is properly adjusted.
Warning
●
Seat belts are designed to
bear upon the bony structure of
the body, and should be worn
low across the front of the
pelvis, or the pelvis, chest and
shoulders,
as
applicable;
wearing the lap section of the
belt across the abdominal area
must be avoided. Serious injury
can occur if seat belt is not
worn properly.
●
No
modifications
or
additions should be made
●
by the user which will
either prevent the seat belt
adjusting
devices
from
operating to remove slack, or
prevent the seat belt assembly
from being adjust to remove
slack.
●
Seat
belts
should
be
adjusted as firmly as possible,
consistent with comfort, to
pro-vide the protection for
which they have been designed.
A slack belt will greatly reduce
the protection afforded to the
wearer. Care should be taken to
avoid contamination of the
webbing with polishes, oils and
chemicals,
and
particularly
battery acid. Cleaning may
safely be carried out using mild
soap and water. The belt
should be replaced if webbing
becomes frayed, contaminated
or damaged.
●
It is essential to replace the
entire assembly after it has
been worn in a severe impact
even if damage to the assembly
is not obvious.
●
Belts should not be worn
with straps twisted.
●
Each seat belt assembly
must only be used by one
occupant; it is dangerous to
put a belt around a child being
carried on the occupant
’s lap.
●
All seat belt assemblies
including
retractors
and
attaching hardware should be
inspected after any collision at
your Zhengzhou NISSAN dealer.
Zhengzhou
NISSAN
recommends that all seat belt
assemblies in use during a
collision be replaced unless the
collision was minor and the
belts show no damage and
continue to operate properly.
Seat belt assemblies not in use
during a collision should also
be inspected and replaced if
either damage or improper
operation is noted.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
2-16 Pre-driving checks and adjustments
Pregnant women
Zhengzhou NISSAN recommends
that pregnant women use seat
belts. Contact your doctor for
specific recommendations. The
lap belt should be worn snug and
positioned as low possible around
the hips, not the waist.
Injured persons
Zhengzhou NISSAN recommends
that injured persons use seat
belts, depending on the injury.
Check with your doctor for
specific recommendations.
SEAT BELT MAINTENANCE
To clean the seat belt webbings,
apply a mild soap solution or any
solution
recommended
for
cleaning upholstery or carpets.
Then brush it, wipe with a cloth
and allow it to dry in the shade.
Do not allow the seat belts to
retract until they are completely
dry.
If dirt builds up in the shoulder
belt guide of the seat belt anchors,
the seat belts may retract slowly.
Wipe the shoulder belt guide with
a clean, dry cloth.
Periodically check to see that the
seat
belt
and
the
metal
components such as buckles,
tongues, retractors, flexible wires
and anchors work properly. If
loose parts, deterioration, cuts or
other damage on the webbing is
found, the entire belt assembly
should be replaced.
3-Point Type With Retractor
Fastening The Belts
1
, Adjust the seat
Warning
●
The seatback should not
be reclined any more than
needed for comfort. Seat belts
are most effective when the
passenger sits well back and
straight up in the seat.
●
If the seatback is reclined,
the risk of sliding under the lap
belt and being injured is
increased.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Pre-driving checks and adjustments 2-17
2
, Slowly pull the seat belt out
of the retractor and insert the
tongue into the buckle until it
snaps.
The retractor is designed to
lock during a sudden stop or
on impact. A slow pulling
motion will permit the belt to
move, and allow you some
freedom of movement in the
seat.
3
, Position the lap belt portion
low on the hips as shown.
4
, Pull the shoulder belt portion
toward the retractor to take up
extra slack.
Warning
●
The seat belt should rest
on the middle of the shoulder.
It must not rest against the
neck.
●
Make sure that the seat belt
is not twisted in any way.
Unfastening the belts
To unfasten the belt, press the
button on the buckle. The seat
belt will automatically retract.
Checking seat belt operation
Your seat belt retractors are
designed to lock belt movement
by two separate methods:
1
, When the belt is pulled
quickly from the retractor.
2
, When the vehicle slows down
rapidly.
To increase your confidence in
the belts, check the operation
as follows: Grasp the shoulder
belt and pull quickly forward.
The retractor should lock and
restrict further belt movement.
If the retractor does not lock
during these checks or if you
have any question about belt
operation see your Zhengzhou
NISSAN dealer.
2-Point Type Without Retractor
(If So Equipped)
Fastening the belts
1
, Insert the tongue into the
buckle until it snaps.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
2-18 Pre-driving checks and adjustments
2
, To lengthen, hold the tongue
at a right angle to the belt and pull
on the belt. To shorten, pull the
free end of the belt away from the
tongue then pull the belt clip to
take up the slack.
3
, Position the lap belt low on
the hips as illustrated.
Unfastening the belts
To unfasten the belt, press the
button on the buckle.
Fasten the seat belts when not in
use to prevent them from being
caught in the door.
PARKING BRAKE LEVER
To apply : pull the lever up.
To release: pull the lever up
slightly, push the button and lower
completely. Before driving, be
sure the parking brake warning
light goes out.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Pre-driving checks and adjustments 2-19
TILTING STEERING WHEEL
Push the lever down and adjust
the steering wheel up or down to
the desired position. Push the
lock lever up securely to lock the
steering wheel in place.
Warning
Do not adjust the steering
wheel while driving.
OUTSIDE MIRROR
Remote control type
Push the right or left end of the
switch to adjust the right or left
side mirror, then control the lever.
Warning
Check the position of all
mirrors before driving. Altering
position while driving could
distract your attention from the
driving operation.
REARVIEW MIRROR
The night position will reduce
glare from the headlights of
vehicles behind you at night.
Caution
Use the night position only
when necessary, because it
reduce rear view clarity.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
2-20 Pre-driving checks and adjustments
REMOTE KEYLESS ENTRY
SYSTEM
(IF SO EQUIPPED)
With the remote keyless entry
system you could lock/unlock all
doors, active the panic alarm and
find the car from outside the car.
Be sure to remove the key from
the vehicle before locking the
doors and leaving it.
As many as four key fobs can be
used with one vehicle. For more
information
concerning
the
purchase and use of addition key
fobs, contact your Zhengzhou
NISSAN dealer.
The key fob will not function
when:
The battery in the key fob is
dead.
The distance between the
key fob and vehicle is more than
8m.
Caution
●
Do not allow the key fob to
be wet.
●
Do not drop the key fob.
●
Do not strike the key fob
sharply to another object.
●
Do not place the key fob
for an extended period in an
area where temperature exceed
)
140
(
60
0
0
F
C
.
If a key fob is stolen, Zhengzhou
NISSAN recommends erasing the
ID code of that key fob. This will
prevent
the
key
fob
from
unauthorized use to unlock the
vehicle. For information regarding
the erasing procedure, please
contact your Zhengzhou NISSAN
dealer.
Locking door
1. Remove the ignition key.
2. Close all of the doors.
3. Push the LOCK button on the
key fob.
4. The hazard indicators flash
twice, all of doors will lock.
5. If you lock the doors with any
door unclosed well, the hazard
indicators will flash three times,
please close the door well and
then lock it with the key fob.
Although door locking with carob
can be confirmed by looking at
the hazard indicator, always
check to be sure that the doors
are properly before leaving your
vehicle.
Unlocking door
1. Push the UNLOCK button on
the key fob.
2. The hazard indicators flash
once and unlock all doors.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Pre-driving checks and adjustments 2-21
Finding car
1. Push the TRUNK button on
the key fob, the hazard indicators
will flash for 15S to remind the
vehicle owner.
2. Push the TRUNK button
again to cancel reminding.
Panic
In any case, push the PANIC
button on the key fob, the horn
will tweet loudly and the hazard
indicators will flash at the same
time, all these will be turned off by
themselves after 25S, if you push
the PANIC button in 25S again it
will turn them off also.
Auto lock
After locking doors well, it will be
locked automatically if there is no
operation of opening door or
operating ignition key in 25S
when the door is opened by
pushing the
“UNLOCK” button
haphazard,
then
the
hazard
indicators flash once.
If you use the key to lock doors, it
only can lock the driver
’s side
door, please use the remote
keyless entry system to all doors.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Heater, air conditioner and audio system
1
3. HEATER, AIR CONDITIONER AND AUDIO SYSTEM
CENTER AND SIDE VENTS . . . . . ... 3-2
HEATER AND AIR CONDITIONER. . . . 3-2
AIR CONDITIONER OPERATION (IF SO
EQUIPPED) . . . . . . . . . . . . . 3-5
-------------------------------------------------------------------------------------------------------------------------------------------------------------
2 Heater, air conditioner and audio system
CENTER AND SIDE VENTS
Open or close (if so equipped),
and adjust the air flow direction of
the ventilators.
HEATER AND AIR
CONDITIONER
CONTROLS
Fan control lever/dia
l
This lever/dial turns the fan on
and off, and controls fan speed.
Air flow control lever/dial
This lever/dial allows you to select
the air flow outlets.
— Air flows from center and
side ventilators.
— Air flows from center and
side ventilators and foot outlets.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Heater, air conditioner and audio system
3
— Air flows mainly from foot
outlets.
— Air flows from defroster
outlets and foot outlets.
— Air flows mainly from
defroster outlets.
Temperature control lever/dial
This lever/dial allows you to adjust
the temperature of the outlet air.
(Except models without heater)
Air intake lever/Air recirculation
button
position/
button
off
position (Indicator goes out)
Outside air is drawn into the
passenger compartment.
Use this position for normal heater,
or air conditioner operation.
If dust is not raised in front of the
vehicle, this position is effective to
prevent dust entry.
position/
button
on
position (Indicator comes on)
Interior air is recirculated inside
the vehicle.
Move the air intake lever to this
position/push the”
” button to
the on position when driving on a
dust raised road or to avoid traffic
fumes.
WARNING:
Do not use in this position for long
periods of time because it may
cause the interior air to become
stuffy and the windows to fog up.
Air conditioner button (If so
equipped)
This button is provided only for
vehicles with an air conditioner.
Start the engine, move the fan
control lever/dial to the desired (1
to 4) position and push the air
conditioner button to turn on the
air conditioner. The indicator light
will come on when the air
conditioner is on. To stop the air
conditioner, push the switch again
to return it to the original position.
The air conditioner cooling
function operates only when
the engine is running.
WARNING:
Positioning of the heating or air
conditioning controls should
not be done while driving, in
order that full attention may be
given to the driving operation.
HEATER OPERATION
Heating
This mode is used to direct hot air
from the floor outlets.
1.
Move the air intake lever to
the”
” position, or push
the”
” button to the off
position for normal heating
.
2.
Move the air control lever/dial
to the
position
.
3.
Turn on the fan control
lever/dia
l.
4.
Move the temperature control
lever/dial
to
the
desired
position between the middle
and the “HOT” position
.
Ventilation
This mode directs outside air from
the side and center vents
.
1.
Move the air intake lever to
the”
” position, or push
the”
” button to the off
position
.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
4 Heater, air conditioner and audio system
2.
Move the air control lever/dial
to the”
”position
.
3.
Turn on the fan control
lever/dial.
4.
Move the temperature control
lever/dial
to
the
desired
position
.
Defrosting or defogging
This
mode
is
used
to
defrost/defog the windows
.
1.
Move the air intake lever to
the”
” position, or push
the”
” button to the off
position
.
2.
Move the air control lever/dial
to the”
” position
.
3.
Turn on the fan control
lever/dial
.
4.
Move the temperature control
lever/dial
to
the
desired
position between the middle
and the “HOT” position.
5.
Push on the air conditioner
button. The indicator light will
come on
.
Bi-level heating
This mode directs outside air from
side and center vents and hot air
from the floor outlets
.
1.
Move the air intake lever to
the”
” position, or push
the”
” button to the off
position.
2.
Move the air control lever/dial
to the”
”position
.
3.
Turn on the fan control
lever/dial.
4.
Normally
move
the
temperature control lever/dial
to
the
midpoint between
"HOT" and "COLD"
.
Heating and defrosting
This mode heats the interior and
defogs the windshield
.
1.
Move the air intake lever to
the”
” position, or push
the”
” button to the off
position
.
2.
Move the air control lever/dial
to the”
”position
.
3.
Turn on the fan control
lever/dial.
4.
Move the temperature control
lever/dial
to
the
desired
position between the middle
and the “HOT” position
.
Operating tips
Clear snow and ice from the
wiper blade and air inlet in front
of the windshield. This will
improve heater and defroster
operation.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Heater, air conditioner and audio system
5
AIR CONDITIONER
OPERATION (If so
equipped)
Start the engine, move the fan
control lever/dial to the desired (1
to 4) position and push in the air
conditioner button to activate the
air conditioner. When the air
conditioner is on, cooling and
dehumidifying functions will be
added to the heater operation
.
The air conditioner cooling
function operates only when
the engine is running.
Cooling
This mode is used to cool and
dehumidify
.
1.
Move the air intake lever to
the”
” position, or push
the”
” button to the off
position
.
2.
Move the air control lever/dial
to the”
”position
.
3.
Turn on the fan control
lever/dial.
4.
Push on the air conditioner
button. The indicator light will
come on
.
5.
Move the temperature control
lever/dial
to
the
desired
position.
For quick cooling, move the
air intake lever to the
“
”
position, or push the
“
”
button to the on position. Be
sure to return the air intake
lever to the
“
” position, or
push the
“
” button to the
off
position
for
normal
cooling
.
Dehumidified heating
This mode is used to heat and
dehumidify
.
1.
Move the air intake lever to
the
“
” position, or push the
“
” button to the off
position
.
2.
Move the air control lever/dial
to the
“
” position
.
3.
Turn on the fan control
lever/dial.
4.
Push on the air conditioner
button. The indicator light will
come on
.
5.
Move the temperature control
lever/dial
to
the
desired
position
.
Dehumidified defrosting
This
mode
is
used
to
defrost/defog the windows and
dehumidify
.
1.
Move the air intake lever to
the
“
” position, or push the
“
” button to the off
position
.
2.
Move the air control lever/dial
to the
“
” position
.
3.
Turn on the fan control
lever/dial
.
4.
Push on the air conditioner
button. The indicator light will
come on.
5.
Move the temperature control
lever/dial
to
the
desired
position
.
Operating tips
Keep windows and sun roof
closed
while
the
air
conditioner is in operation
.
After parking in the sun, drive
for two or three minutes with
the windows open to vent hot
-------------------------------------------------------------------------------------------------------------------------------------------------------------
6 Heater, air conditioner and audio system
air
from
the
passenger
compartment. Then, close
the windows. This will allow
the air conditioner to cool the
interior more quickly
.
The air conditioning system
should be operated for about
ten minutes at least once a
month, especially in winter.
This helps prevent damage to
the system due to lack of
lubrication.
If the coolant temperature
gauge exceeds the "HOT"
position,
turn
the
air
conditioner off. Have your
Vehicle
inspected
by
PARSKHODRO service center.
See "If your vehicle overheats" in
the “In case of emergency”
section for additional information
.
Servicing air conditioner
The air conditioning system in
your NISSAN vehicle is charged
with a new refrigerant designed
with the environment in mind
.
This new refrigerant will not
harm the earth’s ozone layer.
However it may contribute in a
small part to global warming
.
Special charging equipment and
lubricant
are
required
when
servicing
your
NISSAN
air
conditioner.
Using
improper
refrigerants or lubricants will
cause severe damage to your air
conditioning system. See “Air
conditioning system refrigerant
an
d lubricant recommendations”
in the "Technical information"
section of this manual
.
PARSKHODRO service center
will be able to service your
environmentally
"friendly"
air
conditioning system.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Heater, air conditioner and audio system
7
AUDIO SYSTEM
Please read CD/USB FM player
instruction part for operation and
caution which followed
vehicle’s
audio system
。
AUDIO SYSTEM
CAUTION
:
Please use authorized tape
less than 60minutes
。
Use authorized disk
。
Don
’t start it in a bump road
。
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Starting and driving
4-1
4. STARTING AND DRIVING
BREAK-IN SCHEDULE . . . . . . . .. 4-2
BEFORE STARTING THE ENGINE . . ... 4-2
DRIVING . . . . . . . . . . . . . . 4-3
EXHAUST GAS (CARBON MONOXIDE) ... 4-3
ON-PAVEMENT AND OFF-ROAD . . . .. 4-4
CARE WHEN DRIVING . . . . . . . .. 4-5
TRAILER TOWING . . . . . . . . . . 4-5
IGNITION SWITCH . . . . . . . . . . 4-6
STARTING THE ENGINE . . . . . . ... 4-7
DRIVING WITH MANUAL TRANSMISSION
. . . . . . . . . . . . . . . . . . 4-7
4×4 TRANSFER CASE SHIFTING . . ... 4-10
AUTO-LOCK FREE-RUNNING HUBS . .. 4-11
DRIVING SAFETY PRECAUTIONS . . . 4-15
4×4 TIRES OF 4-WHEEL DRIVE . . . .. 4-17
PARKING . . . . . . . . . . . . ... 4-18
FOR YOUR VEHICLE SECURITY . . . 4-19
PRECAUTIONS WHEN DRIVING . . . 4-19
IN COLD WEATHER . . . . . . . . . 4-22
-------------------------------------------------------------------------------------------------------------------------------------------------------------
4-2
Starting and driving
BREAK-IN SCHEDULE
During the first 1600km,
follow the recommendations for
the future reliability and economy
of your new vehicle. Failure to
follow these recommendations
may results in vehicle damage or
shortened engine life.
Do not drive over the following
speed limits:
●
2-wheel drive models and
4×4
(2H position)
90km/h
●
4×4
(4H position):
80km/h
●
4×4
(4L position):
50km/h
Engine speed
:
DISTANCE
(km)
Weight
Speed
(rpm)
1
0~200
0
2000~3000
2
200~800
≤25%
2000~3500
3
800~1500
≤50%
2000~4000
4
1500~2000
≤75%
2000~4000
Avoid driving for long periods at
constant speed, either fast or
slow.
●
Do not accelerate hard in
top gear.
●
Avoid quick starts and full
acceleration.
●
Avoid hard stops as much
as possible.
●
Do not tow a trailer for the
first 800 km.
●
Change the engine oil and
oil filter at the first 500km
,
2000km
in
the
break-in
schedule
。
BEFORE STARTING THE
ENGINE
WARNING:
The driving characteristics of
your vehicle can be changed
remarkably by any additional
load and its distribution as well
as
by
adding
optional
equipment
(trailer
coupling,
roof rack, etc). Your driving
style and speed have to be
adjusted accordingly especially
when carrying heavy loads,
your speed must be reduced
adequately.
●
Make sure the area around
the vehicle is clear.
●
Check fluid levels such
engine oil, coolant, brake and
clutch fluid, window washer
fluid as frequently as possible,
at least whenever you refuel.
●
Check to be sure that all
windows and light lenses are
clean.
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст