Acura RLX Hybrid (2017 year). Instruction — part 30
472
uu
Maintenance Under the Hood
u
Oil Check
Main
tenan
ce
Oil Check
We recommend that you check the engine oil level every time you refuel.
Park the vehicle on level ground.
Turn off the power system. You can check the oil level without the engine having
run beforehand. If the engine has been running, wait approximately three minutes
before you check the oil.
1. Remove the dipstick (orange loop).
2. Wipe the dipstick with a clean cloth or
paper towel.
3. Insert the dipstick back all the way into its
hole.
4. Remove the dipstick again, and check the
level. It should be between the upper and
lower marks. Add oil if necessary.
1
If the oil level is near or below the lower mark, slowly
add oil being careful not to overfill.
Upper Mark
Lower Mark
17 ACURA RLX E-AWD-31TY36300.book 472 ページ 2016年6月17日 金曜日 午前8時29分
-------------------------------------------------------------------------------------------------------------------------------------------------------------
473
uu
Maintenance Under the Hood
u
Adding Engine Oil
Main
tenan
ce
Adding Engine Oil
1. Unscrew and remove the engine oil fill cap.
2. Add oil slowly.
3. Reinstall the engine oil fill cap, and tighten
it securely.
4. Wait for three minutes and recheck the
engine oil dipstick.
1
If any oil spills, wipe it away immediately. Spilled oil
may damage the engine compartment components.
NOTICE
Do not fill the engine oil above the upper mark.
Overfilling the engine oil can result in leaks and
engine damage.
Engine Oil Fill Cap
17 ACURA RLX E-AWD-31TY36300.book 473 ページ 2016年6月17日 金曜日 午前8時29分
-------------------------------------------------------------------------------------------------------------------------------------------------------------
474
uu
Maintenance Under the Hood
u
Changing the Engine Oil and Oil Filter
Main
tenan
ce
Changing the Engine Oil and Oil Filter
You must change the engine oil and oil filter regularly in order to maintain the
engine’s lubrication. The engine may be damaged if they are not changed regularly.
Turning the power system on automatically starts the engine if the following
conditions are met:
• The SPORT mode is on.
Change the oil and filter in accordance with the maintenance message on the multi-
information display.
1. Run the engine until it reaches normal
operating temperature, and then turn the
engine off.
2. Open the hood and remove the engine oil
fill cap.
3. Remove the drain bolt and washer from
the bottom of the engine, and drain the
oil into a suitable container.
4. Remove the oil filter and dispose of the
remaining oil.
5. Check that the filter gasket is not stuck to
the engine contact surface.
u
If it is stuck, you must detach it.
6. Wipe away dirt and dust adhering to the
contact surface of the engine block, and
install a new oil filter.
u
Apply a light coat of new engine oil to
the oil filter rubber seal.
1
Changing the Engine Oil and Oil Filter
NOTICE
You may damage the environment if you do not
dispose of the oil in a suitable way. If you are
changing the oil by yourself, appropriately dispose of
the used oil. Put the oil in a sealed container and take
it to a recycling center. Do not throw the oil away
into a garbage can or onto the ground.
You will need a special wrench to replace the oil
filter. You can buy this wrench from a dealer.
When installing the new oil filter, follow the
instructions supplied with the oil filter.
Reinstall the engine oil fill cap. Start the engine. The
low oil pressure indicator should go off within five
seconds. If it does not, turn off the engine, and check
your work.
Drain Bolt
Washer
Oil Filter
17 ACURA RLX E-AWD-31TY36300.book 474 ページ 2016年6月17日 金曜日 午前8時29分
-------------------------------------------------------------------------------------------------------------------------------------------------------------
475
uu
Maintenance Under the Hood
u
Changing the Engine Oil and Oil Filter
Main
tenan
ce
7. Put a new washer on the drain bolt, then reinstall the drain bolt.
u
Tightening torque:
29 lbf∙ft (39 N∙m, 4.0 kgf∙m)
8. Pour the recommended engine oil into the engine.
u
Engine oil change capacity (including filter):
4.5 US qt (4.3 L)
9. Reinstall the engine oil fill cap securely and start the engine.
10. Run the engine for a few minutes, and then check that there is no leak from the
drain bolt or oil filter.
11. Stop the engine, wait for three minutes, and then check the oil level on the
dipstick.
u
If necessary, add more engine oil.
17 ACURA RLX E-AWD-31TY36300.book 475 ページ 2016年6月17日 金曜日 午前8時29分
-------------------------------------------------------------------------------------------------------------------------------------------------------------
476
uu
Maintenance Under the Hood
u
Cooling System
Main
tenan
ce
Cooling System
This coolant is premixed with 50% antifreeze and 50% water. Do not add any
straight antifreeze or water.
We recommend you check the engine coolant level every time you refuel. Check the
reserve tank first. If it is completely empty, also check the coolant level in the
radiator. Add the engine coolant accordingly.
1. Check the amount of coolant in the reserve
tank.
2. If the coolant level is below the MIN mark,
add the specified coolant until it reaches
the MAX mark.
3. Inspect the cooling system for leaks.
Specified coolant: Acura Long Life Antifreeze/Coolant Type 2
■
Reserve Tank
1
NOTICE
Genuine Acura engine coolant is a 50/50 mixture of
antifreeze and water that can withstand freezing at
temperatures as low as about -31°F (-35°C). If your
vehicle is consistently subjected to temperatures
below this, the concentration of antifreeze in the
coolant should be increased. Consult a dealer for
details.
If Acura antifreeze/coolant is not available, you may
use another major brand non-silicate coolant as a
temporary replacement. Check that it is a high quality
coolant recommended for aluminum engines.
Continued use of any non-Acura coolant can result in
corrosion, causing the cooling system to malfunction
or fail. Have the cooling system flushed and refilled
with Acura antifreeze/coolant as soon as possible.
Do not add rust inhibitors or other additives to your
vehicle’s cooling system. They may not be compatible
with the coolant or with the engine components.
Reserve
Tank
MAX
MIN
17 ACURA RLX E-AWD-31TY36300.book 476 ページ 2016年6月17日 金曜日 午前8時29分
-------------------------------------------------------------------------------------------------------------------------------------------------------------
477
uu
Maintenance Under the Hood
u
Cooling System
Main
tenan
ce
1. Make sure the engine and radiator are
cool.
2. Remove the engine compartment cover.
2 Engine Compartment Cover P. 470
3. Turn the radiator cap counterclockwise to
relieve any pressure in the cooling system.
Do not push the cap down when turning.
4. Push down and turn the radiator cap
counterclockwise to remove it.
5. The coolant level should be up to the base
of the filler neck. Add coolant if it is low.
6. Put the radiator cap back on, and tighten it
fully.
7. Pour coolant into the reserve tank until it
reaches the MAX mark. Put the cap back
on the reserve tank.
■
Radiator
1
NOTICE
Pour the fluid slowly and carefully so you do not spill
any. Clean up any spills immediately; they can
damage components in the engine compartment.
3
WARNING
Removing the radiator cap while the
engine is hot can cause the coolant to spray
out, seriously scalding you.
Always let the engine and radiator cool
down before removing the radiator cap.
Radiator Cap
17 ACURA RLX E-AWD-31TY36300.book 477 ページ 2016年6月17日 金曜日 午前8時29分
-------------------------------------------------------------------------------------------------------------------------------------------------------------
478
uu
Maintenance Under the Hood
u
Inverter Coolant
Main
tenan
ce
Inverter Coolant
We recommend you check the inverter coolant level every time you refuel.
1. Check the fluid level in the tank.
2. If the coolant level has dropped below the
MIN level, have your vehicle serviced at a
dealer.
u
Only a properly trained technician can
refill the coolant and check the system
for leaks.
Transmission Fluid
Have a dealer check the fluid level and replace if necessary.
Do not attempt to check or change the automatic transmission fluid yourself.
Specified coolant: Acura Long Life Antifreeze/Coolant Type 2
■
Checking the Coolant
MAX
MIN
Filler
Tank
■
Dual Clutch Transmission Fluid
Specified fluid: Acura Automatic Transmission Fluid ATF DW-1
1
Dual Clutch Transmission Fluid
NOTICE
Do not mix Acura ATF DW-1 with other
transmission fluids.
Using a transmission fluid other than Acura ATF
DW-1 may adversely affect the operation and
durability of your vehicle’s transmission, and damage
the transmission.
Any damage caused by using a transmission fluid that
is not equivalent to Acura ATF DW-1 is not covered
by Acura’s new vehicle warranty.
17 ACURA RLX E-AWD-31TY36300.book 478 ページ 2016年6月17日 金曜日 午前8時29分
-------------------------------------------------------------------------------------------------------------------------------------------------------------
479
uu
Maintenance Under the Hood
u
Brake Fluid
Main
tenan
ce
Brake Fluid
The fluid level should be between the MIN
and MAX marks on the side of the reserve
tank.
Refilling Window Washer Fluid
If the washer fluid is low, a message appears on the multi-information display.
Pour the washer fluid carefully. Do not overflow the reservoir.
Specified fluid: Acura Heavy Duty Brake Fluid DOT 3
■
Checking the Brake Fluid
1
NOTICE
Brake fluid marked DOT 5 is not compatible with your
vehicle’s braking system and can cause extensive
damage.
If the specified brake fluid is not available, you should
use only DOT 3 or DOT 4 fluid from a sealed
container as a temporary replacement.
Using any non-Acura brake fluid can cause corrosion
and decrease the longevity of the system. Have the
brake system flushed and refilled with Acura Heavy
Duty Brake Fluid DOT 3 as soon as possible.
If the brake fluid level is at or below the MIN mark,
have a dealer inspect the vehicle for leaks or worn
brake pads as soon as possible.
MIN
Reserve Tank
MAX
1
NOTICE
Do not use engine antifreeze or a vinegar/water
solution in the windshield washer reservoir.
Antifreeze can damage your vehicle’s paint. A
vinegar/water solution can damage the windshield
washer pump.
17 ACURA RLX E-AWD-31TY36300.book 479 ページ 2016年6月17日 金曜日 午前8時29分
-------------------------------------------------------------------------------------------------------------------------------------------------------------
480
Main
tenan
ce
Replacing Light Bulbs
Headlights
Headlights are LED type. Have an authorized Acura dealer inspect and replace the
light assembly.
Daytime Running Lights
Daytime running lights are LED type. Have an authorized Acura dealer inspect and
replace the light assembly.
Fog Lights
Fog lights are LED type. Have an authorized Acura dealer inspect and replace the
light assembly.
Front Turn Signal/Parking Lights
Front turn signal/parking lights are LED type. Have an authorized Acura dealer
inspect and replace the light assembly.
1
The headlight aim is set by the factory, and does not
need to be adjusted. However, if you regularly carry
heavy items in the trunk, have the aiming readjusted
at a dealer or by a qualified technician.
17 ACURA RLX E-AWD-31TY36300.book 480 ページ 2016年6月17日 金曜日 午前8時29分
-------------------------------------------------------------------------------------------------------------------------------------------------------------
481
uu
Replacing Light Bulbs
u
Front Side Marker Light Bulbs
Main
tenan
ce
Front Side Marker Light Bulbs
When replacing, use the following bulbs.
1. Turn the steering wheel all the way to the
opposite side from the light being replaced.
Passenger’s side: Turn the steering wheel
to the left.
Driver’s side: Turn the steering wheel to
the right.
2. Remove the holding clips (A) and (B), pull
the inner fender back.
2 Engine Compartment Cover P. 470
3. Turn the socket counter-clockwise and
remove it, then remove the old bulb.
4. Insert a new bulb.
Side Turn Signal/Emergency Indicator Lights
Door mirror side turn lights are LED type. Have an authorized Acura dealer inspect
and replace the light assembly.
Front Side Marker Light: 2 CP
1
When removing the clip, insert a flat-tip screwdriver,
then lift and remove the clip.
Insert the clip with the pin raised, and push until it is
flat.
Holding clip (B-type)
Clip
Push until the
pin is flat.
Inner Fender
Clip (A)
Clips (B)
Bulb
Socket
17 ACURA RLX E-AWD-31TY36300.book 481 ページ 2016年6月17日 金曜日 午前8時29分
-------------------------------------------------------------------------------------------------------------------------------------------------------------
482
uu
Replacing Light Bulbs
u
Rear Turn Signal Light Bulbs
Main
tenan
ce
Rear Turn Signal Light Bulbs
When replacing, use the following bulbs.
1. Remove the cover.
2. Turn the socket counter-clockwise and
remove it, then remove the old bulb.
3. Insert a new bulb.
Rear Turn Signal Light: 21 W
Left side
Cover
Cover
Right side
Bulb
Socket
17 ACURA RLX E-AWD-31TY36300.book 482 ページ 2016年6月17日 金曜日 午前8時29分
-------------------------------------------------------------------------------------------------------------------------------------------------------------
483
uu
Replacing Light Bulbs
u
Brake/Taillight and Rear Side Marker Lights
Continued
Main
tenan
ce
Brake/Taillight and Rear Side Marker Lights
Brake/taillight and rear side marker lights are LED type. Have an authorized Acura
dealer inspect and replace the light assembly.
Taillights
Taillights are LED type. Have an authorized Acura dealer inspect and replace the light
assembly.
Back-Up Light Bulbs
When replacing, use the following bulbs.
1. Remove the cover.
Back-Up Light: 16 W
Cover
17 ACURA RLX E-AWD-31TY36300.book 483 ページ 2016年6月17日 金曜日 午前8時29分
-------------------------------------------------------------------------------------------------------------------------------------------------------------
484
uu
Replacing Light Bulbs
u
Rear License Plate Lights
Main
tenan
ce
2. Turn the socket counter-clockwise and
remove it, then remove the old bulb.
3. Insert a new bulb.
Rear License Plate Lights
Rear license plate lights are LED type. Have an authorized Acura dealer inspect and
replace the light assembly.
High-Mount Brake Light
High-mount brake light is LED type. Have an authorized Acura dealer inspect and
replace the light assembly.
Door Outer Handle Ambient Lights
Door outer handle ambient lights are LED type. Have an authorized Acura dealer
inspect and replace the light assembly.
Socket
Bulb
17 ACURA RLX E-AWD-31TY36300.book 484 ページ 2016年6月17日 金曜日 午前8時29分
-------------------------------------------------------------------------------------------------------------------------------------------------------------
485
Continued
Main
tenan
ce
Checking and Maintaining Wiper Blades
Checking Wiper Blades
If the wiper blade rubber has deteriorated, it will leave streaks and the hard surfaces
of the blade may scratch the window glass.
Changing the Wiper Blade Rubber
1. Set the power mode to VEHICLE OFF
(LOCK).
2. While holding the wiper switch in the
MIST position, set the power mode to ON,
then to VEHICLE OFF (LOCK).
u
Both wiper arms are set to the
maintenance position as shown in the
image.
3. Lift both wiper arms.
1
Changing the Wiper Blade Rubber
NOTICE
Avoid dropping the wiper arm; it may damage the
windshield.
17 ACURA RLX E-AWD-31TY36300.book 485 ページ 2016年6月17日 金曜日 午前8時29分
-------------------------------------------------------------------------------------------------------------------------------------------------------------
486
uu
Checking and Maintaining Wiper Blades
u
Changing the Wiper Blade Rubber
Main
tenan
ce
4. Press and hold the tab, then slide the
blade out from the wiper arm.
5. Pull the end of the wiper blade to the
direction of the arrow in the image until it
unfastens from the holder’s end cap.
6. Pull the wiper blade to the opposite
direction to slide it out from its holder.
Tab
Wiper
Blade
End Cap at
the bottom
Holder
17 ACURA RLX E-AWD-31TY36300.book 486 ページ 2016年6月17日 金曜日 午前8時29分
-------------------------------------------------------------------------------------------------------------------------------------------------------------
487
uu
Checking and Maintaining Wiper Blades
u
Changing the Wiper Blade Rubber
Main
tenan
ce
7. Insert the flat side of the new wiper blade
onto the bottom part of the holder. Insert
the blade all the way.
8. Install the end of the wiper blade into the
cap.
9. Slide the wiper blade onto the wiper arm
until it locks.
10. Lower both wiper arms.
11. Set the power mode to ON and hold the
wiper switch in the MIST position until
both wiper arms return to the standard
position.
Cap
Wiper
Blade
Holder
17 ACURA RLX E-AWD-31TY36300.book 487 ページ 2016年6月17日 金曜日 午前8時29分
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст