Acura ILX (2018 year). Instruction — part 32
501
uu
If a Tire Goes Flat
u
Changing a Flat Tire
Continued
Han
d
lin
g the U
n
expected
5. Place the compact spare tire (wheel side up)
under the vehicle body, near the tire that
needs to be replaced.
6. Loosen each wheel nut about one turn
using the wheel nut wrench.
18 ACURA ILX-31TX66500.book 501 ページ 2017年8月25日 金曜日 午前11時31分
-------------------------------------------------------------------------------------------------------------------------------------------------------------
uu
If a Tire Goes Flat
u
Changing a Flat Tire
502
Han
d
lin
g the U
n
expected
1. Place the jack under the jacking point
closest to the tire to be changed.
2. Turn the end bracket clockwise as shown in
the image until the top of the jack contacts
the jacking point.
u
Make sure that the jacking point tab is
resting in the jack notch.
3. Raise the vehicle, using the jack handle bar
and the jack handle, until the tire is off the
ground.
■
How to Set Up the Jack
1
Do not use the jack with people or luggage in the
vehicle.
Use the jack provided in your vehicle.
Other jacks may not support the weight (“load”) or
may not fit the jacking point.
The following instructions must be followed to use
the jack safely:
•
Do not use while the engine is running.
•
Use only where the ground is firm and level.
•
Use only at the jacking points.
•
Do not get in the vehicle while using the jack.
•
Do not put anything on top of or underneath the
jack.
3
WARNING
The vehicle can easily roll off the jack,
seriously injuring anyone underneath.
Follow the directions for changing a tire
exactly, and no person should place any
portion of their body under a vehicle that is
supported by a jack.
Jack
Handle
Bar
Wheel Nut
Wrench as Jack Handle
18 ACURA ILX-31TX66500.book 502 ページ 2017年8月25日 金曜日 午前11時31分
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Continued
503
uu
If a Tire Goes Flat
u
Changing a Flat Tire
Han
d
lin
g the U
n
expected
1. Remove the wheel nuts and flat tire.
2. Wipe the mounting surfaces of the wheel
with a clean cloth.
3. Mount the compact spare tire.
4. Screw the wheel nuts until they touch the
lips around the mounting holes, then stop
rotating.
5. Lower the vehicle and remove the jack.
Tighten the wheel nuts in the order
indicated in the image. Go around,
tightening the nuts, two to three times in
this order.
Wheel nut torque:
80 lbf∙ft (108 N∙m, 11 kgf∙m)
■
Replacing the Flat Tire
1
Do not over tighten the wheel nuts by applying extra
torque using your foot or a pipe.
18 ACURA ILX-31TX66500.book 503 ページ 2017年8月25日 金曜日 午前11時31分
-------------------------------------------------------------------------------------------------------------------------------------------------------------
uu
If a Tire Goes Flat
u
Changing a Flat Tire
504
Han
d
lin
g the U
n
expected
1. Remove the center cap.
2. Place the flat tire face down in the spare tire
well.
3. Remove the spacer cone from the wing
bolt, flip it over, and insert it back on the
bolt. Secure the flat tire with the wing bolt.
4. Securely put the jack and wheel nut wrench
back in the tool case. Store the case in the
trunk.
■
Storing the Flat Tire
1
3
WARNING
Loose items can fly around the interior in a
crash and can seriously injure the
occupants.
Store the wheel, jack, and tools securely
before driving.
Center Cap
Spacer
Cone
Wing
Bolt
For compact spare tire
For full-
size tire
18 ACURA ILX-31TX66500.book 504 ページ 2017年8月25日 金曜日 午前11時31分
-------------------------------------------------------------------------------------------------------------------------------------------------------------
505
uu
If a Tire Goes Flat
u
Changing a Flat Tire
Han
d
lin
g the U
n
expected
If you replace a flat tire with the spare tire, the low tire pressure/TPMS indicator
comes on while you are driving. After driving for a few miles (kilometers), the
indicator will start blinking for a short time and then stay on. Tire Pressure
Monitor Problem appears on the multi-information display, but this is normal.
If you replace the tire with a specified regular tire, the warning message on the
multi-information display and the low tire pressure/TPMS indicator will go off after
a few miles (kilometers).
■
TPMS and the Spare Tire
1
The system cannot monitor the pressure of the spare
tire. Instructionly check the spare tire pressure to be sure
that it is correct.
Use the TPMS specific wheels. Each is equipped with
a tire pressure sensor mounted inside the tire behind
the valve stem.
18 ACURA ILX-31TX66500.book 505 ページ 2017年8月25日 金曜日 午前11時31分
-------------------------------------------------------------------------------------------------------------------------------------------------------------
506
Han
d
lin
g the U
n
expected
Engine Does Not Start
Checking the Engine
If the engine does not start, check the starter.
Starter condition
Checklist
Starter doesn’t turn or turns
over slowly.
The battery may be dead. Check
each of the items on the right and
respond accordingly.
Check for a message on the multi-information display.
●
If the To Start, Hold Remote Near Start Button message appears
2 If the Keyless Access Remote Battery is Weak P. 507
u
Make sure the keyless remote is in its operating range.
2 ENGINE START/STOP Button Operating Range P. 136
Check the brightness of the interior lights.
Turn on the interior lights and check the brightness.
●
If the interior lights are dim or do not come on at all
●
If the interior lights come on normally
The starter turns over normally
but the engine doesn’t start.
There may be a problem with the
fuse. Check each of the items on
the right and respond accordingly.
Review the engine start procedure.
Follow its instructions, and try to start the engine again.
2 Starting the Engine P. 356
Check the immobilizer system indicator.
When the immobilizer system indicator is blinking, the engine cannot be started.
2 Immobilizer System P. 129
Check the fuel level.
There should be enough fuel in the tank.
Check the fuse.
Check all fuses, or have the vehicle checked by a dealer.
2 Inspecting and Changing Fuses P. 521
If the problem continues:
1
If you must start the vehicle immediately, use an
assisting vehicle or booster battery to jump start it.
18 ACURA ILX-31TX66500.book 506 ページ 2017年8月25日 金曜日 午前11時31分
-------------------------------------------------------------------------------------------------------------------------------------------------------------
507
uu
Engine Does Not Start
u
If the Keyless Access Remote Battery is Weak
Han
d
lin
g the U
n
expected
If the Keyless Access Remote Battery is Weak
If the beeper sounds, the To Start, Hold Remote Near Start Button message
appears on the multi-information display, and the indicator on the ENGINE START/
STOP button flashes, and the engine won’t start. Start the engine as follows:
1. Touch the center of the ENGINE START/
STOP button with the A logo on the keyless
access remote while the indicator on the
ENGINE START/STOP button is flashing.
The buttons on the keyless access remote
should be facing you.
u
The indicator flashes for about 30
seconds.
2. Depress the brake pedal and press the
ENGINE START/STOP button within 10
seconds after the beeper sounds and the
indicator stays on.
u
If you don’t depress the pedal, the mode
will change to ACCESSORY.
18 ACURA ILX-31TX66500.book 507 ページ 2017年8月25日 金曜日 午前11時31分
-------------------------------------------------------------------------------------------------------------------------------------------------------------
508
uu
Engine Does Not Start
u
Emergency Engine Stop
Han
d
lin
g the U
n
expected
Emergency Engine Stop
The ENGINE START/STOP button may be used to stop the engine due to an
emergency situation even while driving. If you must stop the engine, do either of the
following operations:
• Press and hold the ENGINE START/STOP button for about two seconds.
• Firmly press the ENGINE START/STOP button twice.
The steering wheel will not lock. However, because turning off the engine disables
the power assist the engine provides to the steering and braking systems, it will
require significantly more physical effort and time to steer and slow the vehicle. Use
both feet on the brake pedal to slow down the vehicle and stop immediately in a
safe place.
The power mode is in ACCESSORY when the engine is stopped.
To change the mode to VEHICLE OFF, move the shift position to
(
P after the vehicle
comes to a complete stop.
1
Do not press the button while driving unless it is
absolutely necessary for the engine to be turned off.
18 ACURA ILX-31TX66500.book 508 ページ 2017年8月25日 金曜日 午前11時31分
-------------------------------------------------------------------------------------------------------------------------------------------------------------
509
Continued
Han
d
lin
g the U
n
expected
Jump Starting
Turn off the power to electric devices, such as audio and lights. Turn off the engine,
then open the hood.
1. Connect the first jumper cable to your
vehicle's battery + terminal.
2. Connect the other end of the first jumper
cable to the assisting vehicle's + terminal.
u
Use a 12-volt booster battery only.
u
When using an automotive battery
charger to boost your 12-volt battery,
select a lower charging voltage than 15
volts. Check the charger instruction for the
proper setting.
3. Connect the second jumper cable to the
assisting vehicle's - terminal.
■
Jump Starting Procedure
1
Securely attach the jumper cable clips so that they do
not come off when the engine vibrates. Also be
careful not to tangle the jumper cables or allow the
cable ends to touch each other while attaching or
detaching the jumper cables.
3
WARNING
A battery can explode if you do not follow
the correct procedure, seriously injuring
anyone nearby.
Keep all sparks, open flames, and smoking
materials away from the battery.
Booster Battery
18 ACURA ILX-31TX66500.book 509 ページ 2017年8月25日 金曜日 午前11時31分
-------------------------------------------------------------------------------------------------------------------------------------------------------------
uu
Jump Starting
u
510
Han
d
lin
g the U
n
expected
4. Connect the other end of the second
jumper cable to the engine mounting bolt
as shown. Do not connect this jumper cable
to any other part.
5. If your vehicle is connected to another
vehicle, start the assisting vehicle's engine
and increase its rpm slightly.
6. Attempt to start your vehicle's engine. If it
turns over slowly, check that the jumper
cables have good metal-to-metal contact.
1
Battery performance degrades in cold conditions and
may prevent the engine from starting.
18 ACURA ILX-31TX66500.book 510 ページ 2017年8月25日 金曜日 午前11時31分
-------------------------------------------------------------------------------------------------------------------------------------------------------------
511
uu
Jump Starting
u
Han
d
lin
g the U
n
expected
Once your vehicle's engine has started, remove the jumper cables in the following
order.
1. Disconnect the jumper cable from your vehicle's ground.
2. Disconnect the other end of the jumper cable from the assisting vehicle's battery
- terminal.
3. Disconnect the jumper cable from your vehicle's battery + terminal.
4. Disconnect the other end of the jumper cable from the assisting vehicle's battery
+ terminal.
Have your vehicle inspected by a nearby service station or a dealer.
■
What to Do After the Engine Starts
18 ACURA ILX-31TX66500.book 511 ページ 2017年8月25日 金曜日 午前11時31分
-------------------------------------------------------------------------------------------------------------------------------------------------------------
512
Han
d
lin
g the U
n
expected
Shift Lever Does Not Move
Follow the procedure below if you cannot move the shift lever out of the
(
P
position.
1. Set the parking brake.
2. Remove the built-in key from the keyless
access remote.
3. Wrap a cloth around the tip of a small flat-
tip screwdriver. Put it into the shift lock
release slot as shown in the image, and
remove the cover.
4. Insert the key into the shift lock release slot.
5. While pushing the key down, press the shift
lever release button, and place the shift
lever into
(
N.
u
The lock is now released. Have the shift
lever checked by a dealer as soon as
possible.
■
Releasing the Lock
Cover
Slot
Release Button
Shift Lock Release Slot
18 ACURA ILX-31TX66500.book 512 ページ 2017年8月25日 金曜日 午前11時31分
-------------------------------------------------------------------------------------------------------------------------------------------------------------
513
Continued
Han
d
lin
g the U
n
expected
Overheating
How to Handle Overheating
Overheating symptoms are as follows:
• The temperature gauge needle is at the
mark or the engine suddenly loses
power.
• Steam or spray comes out of the engine compartment.
■
First thing to do
1. Immediately park the vehicle in a safe place.
2. Turn off all accessories and turn on the hazard warning lights.
u
No steam or spray present: Keep the engine running and open the hood.
u
Steam or spray is present: Turn off the engine and wait until it subsides.
Then open the hood.
1
NOTICE
Continuing to drive with the temperature gauge
needle at the
mark may damage the engine.
3
WARNING
Steam and spray from an overheated
engine can seriously scald you.
Do not open the hood if steam is coming
out.
H
H
18 ACURA ILX-31TX66500.book 513 ページ 2017年8月25日 金曜日 午前11時31分
-------------------------------------------------------------------------------------------------------------------------------------------------------------
uu
Overheating
u
How to Handle Overheating
514
Han
d
lin
g the U
n
expected
■
Next thing to do
1. Check that the cooling fan is operating and
stop the engine once the temperature
gauge needle comes down.
u
If the cooling fan is not operating,
immediately stop the engine.
2. Once the engine has cooled down, inspect
the coolant level and check the cooling
system components for leaks.
u
If the coolant level in the reserve tank is
low, add coolant until it reaches the
MAX mark.
u
If there is no coolant in the reserve tank,
check that the radiator is cool. Cover the
radiator cap with a heavy cloth and open
the cap. If necessary, add coolant up to
the base of the filler neck, and put the
cap back on.
■
Last thing to do
Once the engine has cooled sufficiently, restart it and check the temperature gauge.
If the temperature gauge needle has gone down, resume driving. If it has not gone
down, contact a dealer for repairs.
1
If the coolant is leaking, contact a dealer for repairs.
Use water as an emergency/temporary measure only.
Have a dealer flush the system with proper antifreeze
as soon as possible.
3
WARNING
Removing the radiator cap while the
engine is hot can cause the coolant to spray
out, seriously scalding you.
Always let the engine and radiator cool
down before removing the radiator cap.
Reserve
Tank
MAX
MIN
18 ACURA ILX-31TX66500.book 514 ページ 2017年8月25日 金曜日 午前11時31分
-------------------------------------------------------------------------------------------------------------------------------------------------------------
515
Han
d
lin
g the U
n
expected
Indicator, Coming On/Blinking
If the Low Oil Pressure Indicator Comes On
■
Reasons for the indicator to come on
Comes on when the engine oil pressure is low.
■
What to do as soon as the indicator comes on
1. Immediately park the vehicle in a safe place.
2. If necessary, turn the hazard warning lights on.
■
What to do after parking the vehicle
1. Stop the engine and let it sit for approximately one minute.
2. Open the hood and check the oil level.
3. Start the engine and check the low oil pressure indicator.
u
The indicator goes off: Start driving again.
u
The indicator does not go off within 10 seconds: Immediately stop
the engine and contact a dealer for repairs.
If the Charging System Indicator Comes On
■
Reasons for the indicator to come on
Comes on when the battery is not being charged.
■
What to do when the indicator comes on
Turn off the climate control system, rear defogger, and other electrical
systems, and immediately contact a dealer for repairs.
1
If the Low Oil Pressure Indicator Comes On
NOTICE
Running the engine with low oil pressure can cause
serious mechanical damage almost immediately.
1
If the Charging System Indicator Comes On
If you need to stop temporarily, do not turn off the
engine. Restarting the engine may rapidly discharge
the battery.
18 ACURA ILX-31TX66500.book 515 ページ 2017年8月25日 金曜日 午前11時31分
-------------------------------------------------------------------------------------------------------------------------------------------------------------
516
uu
Indicator, Coming On/Blinking
u
If the Malfunction Indicator Lamp Comes On or Blinks
Han
d
lin
g the U
n
expected
If the Malfunction Indicator Lamp Comes On or
Blinks
■
Reasons for indicator lamp to come on or blink
• Comes on when there is a problem with the engine emissions control
system, or the fuel fill cap is missing, or loose.
• Blinks when engine misfiring is detected.
■
What to do when the indicator lamp comes on
Avoid high speeds and immediately get your vehicle inspected at a
dealer.
■
What to do when the indicator lamp blinks
Park the vehicle in a safe place with no flammable items and wait at least
10 minutes or more with the engine stopped until it cools.
■
The message appears on when:
An evaporative system leak is detected. This may be caused by the fuel fill cap being
loose or not being installed.
■
What to do when the message appears:
1. Stop the engine.
2. Check if the fuel fill cap is fully installed.
u
If not, loosen the cap, and then retighten it until it clicks at least once.
3. Drive for several days of normal driving.
u
The message should go off.
■
When the malfunction indicator lamp comes on
The malfunction indicator lamp comes on if the system continues to detect a leak of
gasoline vapor. If this happens, follow the procedures described earlier to check the
fuel fill cap.
■
Check/Tighten Fuel Cap Message
1
If the Malfunction Indicator Lamp Comes On or Blinks
NOTICE
If you drive with the malfunction indicator lamp on,
the emissions control system and the engine could be
damaged.
If the malfunction indicator lamp blinks again when
restarting the engine, drive to the nearest dealer at
31 mph (50 km/h) or less. Have your vehicle
inspected.
18 ACURA ILX-31TX66500.book 516 ページ 2017年8月25日 金曜日 午前11時31分
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст