Acura MDX Hybrid (2017 year). Instruction — part 25

Continued

393

uu

If a Tire Goes Flat

u

Temporarily Repairing a Flat Tire

*

Han

d

lin
g the U

n

expected

■

Getting Ready to Temporarily Repair the Flat Tire

1

Getting Ready to Temporarily Repair the Flat Tire

Repair notification label and speed restriction label
are applied to the side of temporary tire repair kit.

When making a temporary repair, carefully read the
instruction instruction provided with the kit.

Pressure Relief Button

AIR

Repair Notification Label

Speed Restriction Label

Pressure Gauge

Power Plug

Instruction Instruction

Sealant/Air Hose

Inflator Switch

REPAIR

Selector Knob

17 ACURA MDX E-AWD-31TRX6000.book 393 ページ ２０１７年１月２０日 金曜日 午後２時５３分

394

uu

If a Tire Goes Flat

u

Temporarily Repairing a Flat Tire

*

Han

d

lin
g the U

n

expected

1. Pull the handle on the cargo area floor lid

and open the lid.

2. Take out the cargo floor box.

3. Take the kit out of the case.
4. Place the kit face up, on flat ground near

the flat tire, and away from traffic. Do not
place the kit on its side.

Handle

Cargo Floor Box

Case

Tire Repair Kit

17 ACURA MDX E-AWD-31TRX6000.book 394 ページ ２０１７年１月２０日 金曜日 午後２時５３分

Continued

395

uu

If a Tire Goes Flat

u

Temporarily Repairing a Flat Tire

*

Han

d

lin
g the U

n

expected

1. Remove the valve cap from the tire valve

stem.

2. Remove the sealant/air hose from the

packaging.

3. Attach the sealant/air hose onto the tire

valve stem. Screw it until it is tight.

■

Injecting Sealant and Air

1

Injecting Sealant and Air

In cold temperatures, the sealant may not flow easily.
In this situation, warm it up for five minutes before
using.

The sealant can permanently stain clothing and other
materials. Be careful during handling and wipe away
any spills immediately.

3

WARNING

Tire sealant contains substances that are
harmful and can be fatal if swallowed.

If accidentally swallowed, do not induce
vomiting. Drink plenty of water and get
medical attention immediately.

For skin or eye contact, flush with cool
water and get medical attention if
necessary.

Valve Stem

Valve Cap

Sealant/Air Hose

Valve Stem

Sealant/Air Hose

17 ACURA MDX E-AWD-31TRX6000.book 395 ページ ２０１７年１月２０日 金曜日 午後２時５３分

uu

If a Tire Goes Flat

u

Temporarily Repairing a Flat Tire

*

396

Han

d

lin
g the U

n

expected

4. Plug in the compressor to the accessory

power socket.

u

Be careful not to pinch the cord in a
door or window.

u

Do not plug any other electronic
devices into other accessory power
sockets.

2 Accessory Power Sockets P. 208

5. Turn the power system on.

u

Keep the power system on while
injecting sealant and air.

2 Carbon Monoxide Gas P. 75

6. Turn the selector knob to REPAIR.

1

Injecting Sealant and Air

NOTICE

Do not operate the temporary tire repair kit compressor
for more than 15 minutes. The compressor can
overheat and become permanently damaged.

There are three accessory power sockets:

•

In the console compartment

•

In the front of the center pocket

•

In the left side panel in the cargo area

2 Accessory Power Sockets P. 208

Until the sealant injection is complete, the pressure
shown on the pressure gauge will appear higher than
actual. After the sealant injection is complete the
pressure will drop and then begin to rise again as the
tire is inflated with air. This is normal. To accurately
measure the air pressure using the gauge, turn the air
compressor off only after the sealant injection is
complete.

3

WARNING

Running the engine with the vehicle in an
enclosed or even partly enclosed area can
cause a rapid build-up of toxic carbon
monoxide.

Breathing this colorless, odorless gas can
cause unconsciousness and even death.
Only run the engine to power the air
compressor with the vehicle outdoors.

REPAIR

17 ACURA MDX E-AWD-31TRX6000.book 396 ページ ２０１７年１月２０日 金曜日 午後２時５３分

Continued

397

uu

If a Tire Goes Flat

u

Temporarily Repairing a Flat Tire

*

Han

d

lin
g the U

n

expected

7. Press the inflator switch to turn on the

compressor.

u

The compressor starts injecting sealant
and air into the tire.

u

When the sealant injection is complete,
continue to add air.

8. After the air pressure reaches 35 psi (240

kPa), turn off the kit.

u

To check the pressure, occasionally turn
off the compressor and read the gauge.

9. Unplug the power plug from the accessory

power socket.

10. Unscrew the sealant/air hose from the tire

valve stem. Reinstall the valve cap.

11. Press the pressure relief button until the

gauge returns to 0 psi (0 kPa).

Pressure Gauge

ON

OFF

1

Injecting Sealant and Air

If the required air pressure is not reached within 10
minutes, the tire may be too severely damaged for
the kit to provide the necessary seal, and your vehicle
will need to be towed.

See an Acura dealer for a replacement sealant bottle
and proper disposal of an empty bottle.

Sealant/Air Hose

Valve Stem

Pressure Relief Button

17 ACURA MDX E-AWD-31TRX6000.book 397 ページ ２０１７年１月２０日 金曜日 午後２時５３分

398

uu

If a Tire Goes Flat

u

Temporarily Repairing a Flat Tire

*

Han

d

lin
g the U

n

expected

12. Apply the repair notification label to the

flat surface of the wheel.

u

The wheel surface must be clean to
ensure the label adheres properly.

1. Apply the speed restriction label to the

location as shown.

2. Drive the vehicle for about 10 minutes.

u

Do not exceed 50 mph (80 km/h).

3. Stop the vehicle in a safe place.

Repair Notification Label

■

Distributing the Sealant in the Tire

Speed Restriction Label

17 ACURA MDX E-AWD-31TRX6000.book 398 ページ ２０１７年１月２０日 金曜日 午後２時５３分

399

uu

If a Tire Goes Flat

u

Temporarily Repairing a Flat Tire

*

Continued

Han

d

lin
g the U

n

expected

4. Recheck the air pressure using the sealant/

air hose on the compressor.

5. Turn the selector knob to AIR.

u

Do not turn the air compressor on to
check the pressure.

2 Inflating an Under-inflated Tire P. 401

6. If the air pressure is

• Less than 25 psi (175 kPa):

Do not add air or continue driving. The leak
is too severe. Call for help and have your
vehicle towed.

2 Emergency Towing P. 427

• 35 psi (240 kPa) or more:

Continue driving for another 10 minutes or
until you reach the nearest service station,
whichever is sooner. Do not exceed 50 mph
(80 km/h). If you have not reached a service
station, stop and check the tire pressure.

u

If the air pressure does not go down after
10 minutes of driving, you do not need
to check the tire pressure again.

Sealant/Air Hose

AIR

ON

17 ACURA MDX E-AWD-31TRX6000.book 399 ページ ２０１７年１月２０日 金曜日 午後２時５３分

uu

If a Tire Goes Flat

u

Temporarily Repairing a Flat Tire

*

400

Han

d

lin
g the U

n

expected

• Greater than 25 psi (175 kPa), but less

than 35 psi (240 kPa):

Turn the air compressor on to inflate the
tire until the tire pressure reaches 35 psi
(240 kPa).

2 Inflating an Under-inflated Tire P. 401

Then drive carefully for 10 more minutes or
until you reach the nearest service station,
whichever is sooner. Do not exceed 50 mph
(80 km/h). If you have not reached a service
station, stop and check the tire pressure.

u

You should repeat this procedure as long
as the air pressure is within this range.

7. Unscrew the sealant/air hose from the tire

valve stem.
Reinstall the valve cap.

8. Press the pressure relief button until the

gauge returns to 0 psi (0 kPa).

9. Repackage and properly stow the kit.

Pressure Relief Button

1

Distributing the Sealant in the Tire

3

WARNING

Running the engine with the vehicle in an
enclosed or even partly enclosed area can
cause a rapid build-up of toxic carbon
monoxide.

Breathing this colorless, odorless gas can
cause unconsciousness and even death.
Only run the engine to power the air
compressor with the vehicle outdoors.

17 ACURA MDX E-AWD-31TRX6000.book 400 ページ ２０１７年１月２０日 金曜日 午後２時５３分

Continued

401

uu

If a Tire Goes Flat

u

Temporarily Repairing a Flat Tire

*

Han

d

lin
g the U

n

expected

You can use the kit to inflate a non-punctured, under-inflated tire.

1. Open the cargo area floor lid.

2 Getting Ready to Temporarily Repair

the Flat Tire P. 393

2. Remove the kit from the case.
3. Place the kit, face up, on flat ground near

the flat tire, away from traffic. Do not
place the kit on its side.

4. Remove the sealant/air hose from the kit.

5. Remove the valve cap.

6. Attach the sealant/air hose onto the tire

valve stem. Screw it until it is tight.

■

Inflating an Under-inflated Tire

1

Inflating an Under-inflated Tire

NOTICE

Do not operate the temporary tire repair kit
compressor for more than 15 minutes. The
compressor can overheat and become permanently
damaged.

Air Only Hose

Valve Cap

Valve Stem

Air Only Hose

17 ACURA MDX E-AWD-31TRX6000.book 401 ページ ２０１７年１月２０日 金曜日 午後２時５３分

uu

If a Tire Goes Flat

u

Temporarily Repairing a Flat Tire

*

402

Han

d

lin
g the U

n

expected

7. Plug in the kit to the accessory power

socket.

u

Be careful not to pinch the cord in a
door or window.

u

Do not plug any other electronic
devices into other accessory power
sockets.

2 Accessory Power Sockets P. 208

8. Turn the power system on.

u

Keep the power system on while
injecting air.

2 Carbon Monoxide Gas P. 75

9. Turn the selector knob to AIR ONLY.

10. Press the inflator switch to turn on the kit.

u

The compressor starts to inject air into
the tire.

11. Inflate the tire to the specified air pressure.

1

Inflating an Under-inflated Tire

3

WARNING

Running the engine with the vehicle in an
enclosed or even partly enclosed area can
cause a rapid build-up of toxic carbon
monoxide.

Breathing this colorless, odorless gas can
cause unconsciousness and even death.
Only run the engine to power the air
compressor with the vehicle outdoors.

AIR

ON

17 ACURA MDX E-AWD-31TRX6000.book 402 ページ ２０１７年１月２０日 金曜日 午後２時５３分

403

uu

If a Tire Goes Flat

u

Temporarily Repairing a Flat Tire

*

Han

d

lin
g the U

n

expected

12. Turn off the kit.

u

Check the pressure gauge on the air
compressor.

u

If overinflated, press the pressure relief
button.

13. Unplug the kit from the accessory power

socket.

14. Unscrew the sealant/air hose from the tire

valve stem. Reinstall the valve cap.

15. Press the pressure relief button until the

gauge returns to 0 psi (0 kPa).

16. Repackage and properly stow the kit.

Pressure Relief Button

17 ACURA MDX E-AWD-31TRX6000.book 403 ページ ２０１７年１月２０日 金曜日 午後２時５３分

404

Han

d

lin
g the U

n

expected

Power System Won’t Start

Checking the Procedure

When the READY indicator does not come on and the Ready To Drive message
does not appear on the multi-information display, check the following items and
take appropriate action:

Checklist

Condition

What to Do

Check if the related
indicator or multi-
information display
messages come on.

The Temperature Is Too Cold For Vehicle To Operate
message appears.

2 Multi-Information Display (MID) Warning

and Information Messages P. 99

The To Start, Hold Remote Near Start Button message
appears.

u

Make sure the keyless access remote is in its operating range.

2 POWER Button Operating Range P. 164

2 If the Keyless Access Remote Battery is

Weak P. 405

The POWER SYSTEM indicator comes on.

Have your vehicle checked by a dealer.

The transmission system indicator blinks and Transmission
Problem Apply Parking Brake When Parked message
appears.

The power system can be activated as a
temporary measure.

2 If the Transmission System Indicator Blinks

along with the Warning Message P. 416

Check the brightness
of the interior lights.

The interior lights are dim or do not come on at all.

Have the 12-volt battery checked by a dealer.

The interior lights come on normally.

Check all fuses, or have your vehicle checked by
a dealer.

2 Inspecting and Changing Fuses P. 426

Check the gear
position.

The transmission is not in

(

P.

Change the gear position to

(

P.

Check the
immobilizer system
indicator.

When the immobilizer system indicator is blinking, the power
system cannot be turned on.

2 Immobilizer System Indicator P. 90

1

Checking the Procedure

If you must start the vehicle immediately, use an
assisting vehicle to jump start it.

2 Jump Starting P. 407

17 ACURA MDX E-AWD-31TRX6000.book 404 ページ ２０１７年１月２０日 金曜日 午後２時５３分

405

uu

Power System Won’t Start

u

If the Keyless Access Remote Battery is Weak

Han

d

lin
g the U

n

expected

If the Keyless Access Remote Battery is Weak

If the beeper sounds, the To Start, Hold Remote Near Start Button message
appears on the multi-information display, the indicator on the POWER button
flashes, and the READY indicator does not come on.
Turn on the power system as follows:

1. Touch the center of the POWER button

with the A logo on the keyless access
remote while the indicator on the POWER
button is flashing. The buttons on the
keyless access remote should be facing you.

u

The indicator flashes for about 30
seconds.

2. Depress the brake pedal and press the

POWER button within 10 seconds after the
beeper sounds while the indicator stays on.

u

If you don’t depress the pedal, the mode
will change to ACCESSORY.

17 ACURA MDX E-AWD-31TRX6000.book 405 ページ ２０１７年１月２０日 金曜日 午後２時５３分

406

uu

Power System Won’t Start

u

Emergency Power System Off

Han

d

lin
g the U

n

expected

Emergency Power System Off

The POWER button may be used to turn the power system off due to an emergency
situation even while driving. If you must turn the power system off, do either of the
following operations:
• Press and hold the POWER button for about two seconds.
• Firmly press the POWER button three times.

The steering wheel will not lock. However, because turning off the power system
disables the power assist the power system provides to the steering and braking
systems, it will require significantly more physical effort and time to steer and slow
the vehicle. Use both feet on the brake pedal to slow down the vehicle and stop
immediately in a safe place.

The gear position automatically changes to

(

P after the vehicle comes to a complete

stop. Then, the power mode changes to VEHICLE OFF.

1

Emergency Power System Off

Do not press the button while driving unless it is
absolutely necessary for the power system to be
switched off.

17 ACURA MDX E-AWD-31TRX6000.book 406 ページ ２０１７年１月２０日 金曜日 午後２時５３分

407

Continued

Han

d

lin
g the U

n

expected

Jump Starting

Turn off the power to electric devices, such as audio and lights. Turn off the power
system, then open the hood.

1. Pull up on the engine cover, remove it from

the pins.

u

Start on the passenger side and lift up on
the outermost edge of the cover.

u

Move towards the driver side while
applying uniform upward pressure.

2. Connect the first jumper cable to your

vehicle’s 12-volt battery + terminal.

3. Connect the other end of the first jumper

cable to the booster battery + terminal.

u

Use a 12-volt booster battery only.

u

When using an automotive battery
charger to boost your 12-volt battery,
select a lower charging voltage than 15
volts. Check the charger manual for the
proper setting.

4. Connect the second jumper cable to the

booster battery - terminal.

■

Jump Starting Procedure

1

Jump Starting

Securely attach the jumper cables clips so that they
do not come off when the engine vibrates. Also be
careful not to tangle the jumper cables or allow the
cable ends to touch each other while attaching or
detaching the jumper cables.

12-volt Battery performance degrades in cold
conditions and may prevent the engine from starting.

3

WARNING

A 12-volt battery can explode if you do not
follow the correct procedure, seriously
injuring anyone nearby.

Keep all sparks, open flames, and smoking
materials away from the 12-volt battery.

Engine
Cover

Pin

Booster Battery

17 ACURA MDX E-AWD-31TRX6000.book 407 ページ ２０１７年１月２０日 金曜日 午後２時５３分

408

uu

Jump Starting

u

Han

d

lin
g the U

n

expected

5. Connect the other end of the second

jumper cable to the engine hanger as
shown. Do not connect this jumper cable to
any other part.

6. If your vehicle is connected to another

vehicle, start the assisting vehicle’s engine
and increase its rpm slightly.

7. Attempt to start your vehicle’s engine. If it

turns over slowly, check that the jumper
cables have good metal-to-metal contact.

Once your vehicle’s engine has started, remove the jumper cables in the following
order:

1. Disconnect the jumper cable from your vehicle’s ground.
2. Disconnect the other end of the jumper cable from the booster battery -

terminal.

3. Disconnect the jumper cable from your vehicle’s 12-volt battery + terminal.
4. Disconnect the other end of the jumper cable from the booster battery +

terminal.

Have your vehicle inspected by a nearby service station or a dealer.

■

What to Do After the Engine Starts

17 ACURA MDX E-AWD-31TRX6000.book 408 ページ ２０１７年１月２０日 金曜日 午後２時５３分