Nissan Pathfinder (2005 year). Instruction — part 361
TROUBLE DIAGNOSIS
MTC-79
C
D
E
F
G
H
I
K
L
M
A
B
MTC
2005 Pathfinder
Intake Sensor Circuit
EJS003VO
COMPONENT DESCRIPTION
Intake Sensor
The intake sensor is located on the heater & cooling unit. It converts
temperature of air after it passes through the evaporator into a resis-
tance value which is then input to the front air control.
DIAGNOSTIC PROCEDURE FOR INTAKE SENSOR
SYMPTOM: Intake sensor circuit is open or shorted.
1.
CHECK VOLTAGE BETWEEN INTAKE SENSOR AND GROUND
1.
Disconnect intake sensor connector.
2.
Turn ignition switch ON.
3.
Check voltage between intake sensor harness connector M146
terminal 2 and ground.
OK or NG
OK
>> GO TO 2.
NG
>> GO TO 4.
2.
CHECK CIRCUIT CONTINUITY BETWEEN INTAKE SENSOR AND FRONT AIR CONTROL
1.
Turn ignition switch OFF.
2.
Disconnect front air control connector.
3.
Check continuity between intake sensor harness connector
M146 terminal 1 and front air control harness connector M49 ter-
minal 13.
OK or NG
OK
>> GO TO 3.
NG
>> Repair harness or connector.
WJIA1155E
WJIA1156E
2 - Ground
: Approx. 5V
WJIA1278E
1 - 13
: Continuity should exist.
WJIA1157E
MTC-80
TROUBLE DIAGNOSIS
2005 Pathfinder
3.
CHECK INTAKE SENSOR
Refer to
.
OK or NG
OK
>> Replace front air control. Refer to
.
NG
>> Replace intake sensor. Refer to
.
4.
CHECK CIRCUIT CONTINUITY BETWEEN INTAKE SENSOR AND FRONT AIR CONTROL
1.
Turn ignition switch OFF.
2.
Disconnect front air control connector.
3.
Check continuity between intake sensor harness connector
M146 terminal 2 and front air control harness connector M49 ter-
minal 12.
4.
Check continuity between intake sensor harness connector
M146 terminal 2 and ground.
OK or NG
OK
>> Replace front air control. Refer to
.
NG
>> Repair harness or connector.
COMPONENT INSPECTION
Intake Sensor
After disconnecting intake sensor connector, measure resistance
between terminals 1 and 2 at sensor harness side, using the table
below.
If NG, replace intake sensor.
2 - 12
: Continuity should exist.
2 - Ground
: Continuity should not exist.
WJIA1158E
Temperature
°
C (
°
F)
Resistance k
Ω
−
15 (5)
209.0
−
10 (14)
160.0
−
5 (23)
123.0
0 (32)
95.8
5 (41)
74.9
10 (50)
58.9
15 (59)
46.7
20 (68)
37.3
25 (77)
30.0
30 (86)
24.2
35 (95)
19.7
40 (104)
16.1
45 (113)
13.2
WJIA1159E
CONTROL UNIT
MTC-81
C
D
E
F
G
H
I
K
L
M
A
B
MTC
2005 Pathfinder
CONTROL UNIT
PFP:27500
Removal and Installation
EJS003VP
AIR CONTROL
Removal
1.
Remove cluster lid C. Refer to
.
2.
Remove the four screws securing the air control to cluster lid C.
3.
Remove the air control.
Installation
Installation is in the reverse order of removal.
WJIA1290E
MTC-82
INTAKE SENSOR
2005 Pathfinder
INTAKE SENSOR
PFP:27723
Removal and Installation
EJS003VQ
REMOVAL
1.
Remove the front kick plate. Refer to
.
2.
Remove the lower dash side finisher. Refer to
EI-28, "LOWER DASH SIDE FINISHER"
.
3.
Remove the front pillar lower finisher. Refer to
EI-28, "FRONT PILLAR LOWER FINISHER"
.
4.
Remove the assist grip handle
5.
Remove the front pillar upper finisher. Refer to
EI-28, "FRONT PILLAR UPPER FINISHER"
.
6.
Remove the lower glove box. Refer to
IP-14, "LOWER INSTRUMENT PANEL RH AND GLOVE BOX"
.
7.
Remove the upper glove box (cluster lid E). Refer to
IP-10, "INSTRUMENT PANEL ASSEMBLY"
.
8.
Disconnect the intake sensor electrical connector.
NOTE:
The intake sensor is located on the top of the heater and cooling
unit assembly next to the A/C evaporator cover.
9.
Twist the intake sensor to remove the intake sensor from the
heater and cooling unit assembly.
INSTALLATION
Installation is in the reverse order of removal.
WJIA1415E
BLOWER MOTOR
MTC-83
C
D
E
F
G
H
I
K
L
M
A
B
MTC
2005 Pathfinder
BLOWER MOTOR
PFP:27226
Components
EJS003VR
Blower Motor
Removal and Installation
EJS003VS
REMOVAL
1.
Remove the lower glove box assembly. Refer to
IP-14, "LOWER INSTRUMENT PANEL RH AND GLOVE
.
2.
Disconnect the blower motor electrical connector.
3.
Remove the three screws and remove the blower motor.
INSTALLATION
Installation is in the reverse order of removal.
LJIA0136E
1.
Heater and cooling unit assembly
2.
Blower motor
3.
Blower motor resistor
MTC-84
IN-CABIN MICROFILTER
2005 Pathfinder
IN-CABIN MICROFILTER
PFP:27277
Removal and Installation
EJS003VT
FUNCTION
The air inside the passenger compartment is filtered by the in-cabin
microfilters when the heater or A/C controls are set on either the
recirculation or fresh mode. The two in-cabin microfilters are located
in the heater and cooling unit assembly. The rear heater and cooling
unit assembly only draws in air from the passenger compartment to
recirculate into the passenger compartment, so the rear heater and
cooling unit assembly is not equipped with in-cabin microfilters.
REPLACEMENT TIMING
Replacement of the two in-cabin microfilters is recommended on a regular interval depending on the driving
conditions. Refer to
. It may also be necessary to replace the two in-cabin
microfilters as part of a component replacement if the in-cabin microfilters are damaged.
REPLACEMENT PROCEDURE
1.
Open the lower glove box and press in on the sides so that it will
open completely allowing it to hang by the cord.
2.
Remove the screw and remove the in-cabin microfilter cover.
3.
Remove the in-cabin microfilters from the heater and cooling
unit housing.
4.
Insert the first new in-cabin microfilter into the heater and cool-
ing unit housing and slide it over to the right. Insert the second
new in-cabin microfilter into the heater and cooling unit housing.
NOTE:
The in-cabin microfilters are marked with air flow arrows. The
end of the microfilter with the arrow should face the rear of the
vehicle. The arrows should point downward.
LJIA0012E
WLIA0023E
LJIA0134E
LJIA0148E
IN-CABIN MICROFILTER
MTC-85
C
D
E
F
G
H
I
K
L
M
A
B
MTC
2005 Pathfinder
5.
Install the in-cabin microfilter cover.
6.
Close the lower glove box completely.
LJIA0134E
MTC-86
HEATER & COOLING UNIT ASSEMBLY
2005 Pathfinder
HEATER & COOLING UNIT ASSEMBLY
PFP:27110
Components
EJS003VU
Heater and Cooling Unit Assembly
Removal and Installation
EJS003VV
REMOVAL
1.
Discharge the refrigerant from the A/C system. Refer to
ATC-151, "Discharging Refrigerant"
.
2.
Drain the coolant from the engine cooling system. Refer to
MA-13, "DRAINING ENGINE COOLANT"
.
3.
Disconnect the battery negative and positive terminals.
WJIA1416E
1.
High-pressure A/C pipe
2.
Low-pressure A/C pipe
3.
Expansion valve
4.
Heater core and evaporator pipes
grommet
5.
A/C drain hose grommet
6.
A/C drain hose
7.
Heater core pipe mounts
8.
Heater core pipes
9.
Heater and cooling unit assembly
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст