Nissan Pathfinder (2005 year). Instruction — part 277
POWER WINDOW SYSTEM
GW-23
C
D
E
F
G
H
J
K
L
M
A
B
GW
2005 Pathfinder
WIWA0738E
GW-24
POWER WINDOW SYSTEM
2005 Pathfinder
WIWA0739E
POWER WINDOW SYSTEM
GW-25
C
D
E
F
G
H
J
K
L
M
A
B
GW
2005 Pathfinder
WIWA0528E
GW-26
POWER WINDOW SYSTEM
2005 Pathfinder
Terminal and Reference Value for Main Power Window and Door Lock/Unlock
Switch
EIS0041L
Terminal
Wire Color
Item
Condition
Voltage (V)
(Approx.)
1
R
Rear power window LH
UP signal
When rear LH switch in
main power window and door
lock/unlock switch is operated
UP
Battery voltage
2
BR
Limit switch and encoder ground
—
0
3
LG
Rear power window LH
DOWN signal
When rear LH switch in
main power window and door
lock/unlock switch is operated
DOWN
Battery voltage
5
P
Rear power window RH
DOWN signal
When rear RH switch in
main power window and door
lock/unlock switch is operated
DOWN
Battery voltage
7
Y
Rear power window RH
UP signal
When rear RH switch in
main power window and door
lock/unlock switch is operated
UP
Battery voltage
8
L/W
Front power window motor RH UP
signal
When power window motor is
operated UP
Battery voltage
9
Y
Limit switch signal
Driver side door window is
between fully-open and just
before fully-closed position (ON)
0
Driver side door window is
between just before fully-closed
position and fully-closed position
(OFF)
5
10
W/R
RAP signal
When ignition switch ON
Battery voltage
Within 45 seconds after ignition
switch is turned to OFF
Battery voltage
More than 45 seconds after igni-
tion switch is turned to OFF
0
When front door LH or RH open
or power window timer operates
0
11
G/Y
Front power window motor RH
DOWN signal
When power window motor is
operated DOWN
Battery voltage
12
GR
Front power window motor LH
DOWN signal
When power window motor is
operated DOWN
Battery voltage
13
LB
Encoder pulse signal
When power window motor oper-
ates
15
W/R
Encoder power supply
When ignition switch ON or
power window timer operates
10
16
O
Front power window motor LH UP
signal
When power window motor is
operated UP
Battery voltage
17
B
Ground
—
0
19
L
Battery power supply
—
Battery voltage
OCC3383D
POWER WINDOW SYSTEM
GW-27
C
D
E
F
G
H
J
K
L
M
A
B
GW
2005 Pathfinder
Terminal and Reference Value for BCM
EIS0041N
Terminal
Wire Color
Item
Condition
Voltage (V)
(Approx.)
11
G/B
Ignition switch (ACC or ON)
Ignition switch
(ACC or ON position)
Battery voltage
12
LG
Front door switch RH signal
ON (Open)
Battery voltage
OFF (Close)
0
38
W/R
Ignition switch (ON or START)
Ignition switch
(ON or START position)
Battery voltage
47
GR
Front door switch LH signal
ON (Open)
Battery voltage
OFF (Close)
0
67
B
Ground
—
0
68
O
RAP signal
When ignition switch ON
Battery voltage
Within 45 seconds after ignition
switch is turned to OFF
Battery voltage
More than 45 seconds after igni-
tion switch is turned to OFF
0
When front door LH or RH is
open or power window timer
operates
0
69
L
Power window power supply
—
Battery voltage
70
W
Battery power supply
—
Battery voltage
GW-28
POWER WINDOW SYSTEM
2005 Pathfinder
Work Flow
EIS0041O
1.
Check the symptom and customer's requests.
2.
Understand the outline of system. Refer to
.
3.
According to the trouble diagnosis chart, repair or replace the cause of the malfunction.
Refer to
GW-31, "Trouble Diagnoses Symptom Chart"
.
4.
Does power window system operate normally? Yes, GO TO 5, If No, GO TO 3.
5.
Inspection end.
CONSULT-II Function (BCM)
EIS0041P
CONSULT-II can display each diagnostic item using the diagnostic test modes shown following.
CONSULT-II INSPECTION PROCEDURE
CAUTION:
If CONSULT-II is used with no connection of CONSULT-II CONVERTER, malfunctions might be
detected in self-diagnosis depending on control unit which carries out CAN communication.
1.
Connect CONSULT-II and CONSULT-II CONVERTER to the
data link connector.
2.
Turn ignition switch ON.
3.
Touch “START (NISSAN BASED VHCL)”.
BCM diagnostic
test item
Diagnostic mode
Content
Inspection by part
WORK SUPPORT
Changes setting of each function.
DATA MONITOR
Displays BCM input/output data in real time.
ACTIVE TEST
Operation of electrical loads can be checked by sending drive signal to them.
SELF-DIAG RESULTS
Displays BCM self-diagnosis results.
CAN DIAG SUPPORT
MNTR
The results of transmit/receive diagnosis of CAN communication can be read.
ECU PART NUMBER
BCM part number can be read.
CONFIGURATION
Performs BCM configuration read/write functions.
BBIA0538E
BCIA0029E
POWER WINDOW SYSTEM
GW-29
C
D
E
F
G
H
J
K
L
M
A
B
GW
2005 Pathfinder
4.
Touch “BCM”.
If “BCM” is not indicated, refer to
.
5.
Touch “RETAINED PWR”.
6.
Select diagnosis mode.
“ACTIVE TEST” and “WORK SUPPORT” are available.
ACTIVE TEST
WORK SUPPORT
DATA MONITOR
BCIA0030E
LIIA0163E
BCIA0031E
Test Item
Description
RETAINED PWR
This test is able to supply RAP signal (power) from BCM (body control module) to power window
system and power sunroof system (if equipped). Those systems can be operated when turning on
“RETAINED PWR” on CONSULT-II screen even if the ignition switch is turned OFF.
NOTE:
During this test, CONSULT-II can be operated with ignition switch in OFF position. “RETAINED
PWR” should be turned “ON” or “OFF” on CONSULT-II screen when ignition switch is ON. Then
turn ignition switch OFF to check retained power operation. CONSULT-II might be stuck if
“RETAINED PWR” is turned “ON” or “OFF” on CONSULT-II screen when ignition switch is OFF.
Work item
Description
RETAINED PWR
RAP signal’s power supply period can be changed by mode setting. Selects RAP signal’s power
supply period between three steps
●
MODE1 (45 sec.)/MODE2 (OFF)/MODE 3 (2 min.).
Work item
Description
IGN ON SW
Indicates (ON/OFF) condition of ignition switch
GW-30
POWER WINDOW SYSTEM
2005 Pathfinder
DOOR SW–DR
Indicates (ON/OFF) condition of front door switch driver side
DOOR SW–AS
Indicates (ON/OFF) condition of front door switch passenger side
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст