Nissan Pathfinder (2005 year). Instruction — part 33
ON-VEHICLE SERVICE
AT-235
D
E
F
G
H
I
J
K
L
M
A
B
AT
2005 Pathfinder
11. Remove bolts A, B and C from control valve with TCM.
12. Remove control valve with TCM from transmission case.
CAUTION:
When removing, be careful with the instruction valve notch and
instruction plate height. Remove it vertically.
13. Remove A/T fluid temperature sensor 2 with bracket from con-
trol valve with TCM.
14. Remove bracket from A/T fluid temperature sensor 2.
15. Remove O-ring from A/T assembly harness connector.
Bolt symbol
Length mm (in)
Number of bolts
A
42 (1.65)
5
B
55 (2.17)
6
C
40 (1.57)
1
SCIA5139E
SCIA5142E
SCIA5301E
SCIA5264E
SCIA5155E
AT-236
ON-VEHICLE SERVICE
2005 Pathfinder
16. Disconnect TCM connectors.
CAUTION:
Be careful not to damage connectors.
17. Remove A/T assembly harness connector from control valve
with TCM using suitable tool.
18. Disconnect TCM connector and park/neutral position switch
connector
CAUTION:
Be careful not to damage connectors.
SCIA5447E
SCIA5448E
SCIA5449E
ON-VEHICLE SERVICE
AT-237
D
E
F
G
H
I
J
K
L
M
A
B
AT
2005 Pathfinder
Installation
1.
Connect TCM connector and park/neutral position switch con-
nector.
2.
Install A/T assembly harness connector to control valve with
TCM.
3.
Connect TCM connector.
4.
Install new O-ring in A/T assembly harness connector.
CAUTION:
●
Do not reuse O-ring.
●
Apply ATF to O-ring.
SCIA5449E
SCIA5450E
SCIA5447E
SCIA5155E
AT-238
ON-VEHICLE SERVICE
2005 Pathfinder
5.
Install A/T fluid temperature sensor 2 to bracket.
6.
Install A/T fluid temperature sensor 2 (with bracket) in control
valve with TCM. Tighten A/T fluid temperature sensor 2 bolt to
the specified torque. Refer to
.
CAUTION:
Adjust bolt hole of bracket to bolt hole of control valve with
TCM.
7.
Install control valve with TCM in transmission case.
CAUTION:
●
Make sure that turbine revolution sensor is securely
installed into turbine revolution sensor hole.
●
Hang down revolution sensor harness toward outside so
as not to disturb installation of control valve with TCM.
●
Adjust A/T assembly harness connector of control valve
with TCM to terminal hole of transmission case.
●
Assemble it so that instruction valve cutout is engaged with
instruction plate projection.
SCIA5264E
SCIA5301E
SCIA5034E
SCIA5142E
ON-VEHICLE SERVICE
AT-239
D
E
F
G
H
I
J
K
L
M
A
B
AT
2005 Pathfinder
8.
Install bolts A, B and C in control valve with TCM.
9.
Tighten bolt 1, 2 and 3 temporarily to prevent dislocation. After
that tighten them in order (1
→
2
→
3). Then tighten other bolts.
10. Tighten control valve with TCM bolts to the specified torque.
Refer to
.
11. Connect A/T fluid temperature sensor 2 connector.
12. Securely fasten terminal cord assembly and A/T fluid tempera-
ture sensor 2 harness with terminal clips.
13. Connect revolution sensor connector.
14. Securely fasten revolution sensor harness with terminal clips.
15. Install oil pan to transmission case. Refer to
.
Bolt symbol
Length mm (in)
Number of bolts
A
42 (1.65)
5
B
55 (2.17)
6
C
40 (1.57)
1
SCIA5139E
SCIA5140E
SCIA5446E
SCIA3969E
AT-240
ON-VEHICLE SERVICE
2005 Pathfinder
16. Pull up A/T assembly harness connector.
CAUTION:
Be careful not to damage connector.
17. Install snap ring to A/T assembly harness connector.
18. Connect A/T assembly harness connector.
19. Connect the negative battery terminal.
20. Refill the A/T with fluid and check for fluid leakage. Refer to
24, "Changing the Automatic Transmission Fluid (ATF)"
.
A/T FLUID TEMPERATURE SENSOR 2 REMOVAL AND INSTALLATION
Removal
1.
Disconnect negative battery terminal.
2.
Drain A/T fluid. Refer to
MA-24, "Changing the Automatic Transmission Fluid (ATF)"
.
3.
Remove oil pan and oil pan gasket. Refer to
.
4.
Straighten terminal clip to free A/T fluid temperature sensor 2
harness.
5.
Disconnect A/T fluid temperature sensor 2 connector.
CAUTION:
Be careful not to damage connector.
6.
Remove A/T fluid temperature sensor 2 with bracket from con-
trol valve with TCM.
SCIA5038E
SCIA5039E
SCIA5146E
SCIA5253E
ON-VEHICLE SERVICE
AT-241
D
E
F
G
H
I
J
K
L
M
A
B
AT
2005 Pathfinder
7.
Remove bracket from A/T fluid temperature sensor 2.
Installation
1.
Install A/T fluid temperature sensor 2 to bracket.
2.
Install A/T fluid temperature sensor 2 (with bracket) in control
valve with TCM. Tighten A/T fluid temperature sensor 2 bolt to
the specified torque. Refer to
.
CAUTION:
Adjust bolt hole of bracket to bolt hole of control valve with
TCM.
3.
Connect A/T fluid temperature sensor 2 connector.
4.
Securely fasten A/T temperature sensor 2 harness with terminal
clip.
5.
Install oil pan to transmission case. Refer to
.
6.
Connect the negative battery terminal.
7.
Refill the A/T with fluid and check for fluid leakage. Refer to
MA-24, "Changing the Automatic Transmis-
.
SCIA5264E
SCIA5264E
SCIA5253E
SCIA5146E
AT-242
ON-VEHICLE SERVICE
2005 Pathfinder
Rear Oil Seal
UCS0038D
REMOVAL AND INSTALLATION
Removal
1.
Remove rear propeller shaft. Refer to
.
2.
Remove transfer from transmission (4WD models). Refer to
145, "Removal and Installation"
(ATX14B) or
(TX15B).
3.
Remove rear oil seal using suitable tool.
CAUTION:
Be careful not to scratch rear extension assembly (2WD
models) or adapter case assembly (4WD models).
Installation
1.
Install new rear oil seal into the extension case (2WD models) or
adapter case (4WD models) until it is flush with component face,
using suitable tool or Tool.
CAUTION:
●
Apply ATF to rear oil seal.
●
Do not reuse rear oil seal.
2.
Install transfer to transmission (4WD models). Refer to
(ATX14B) or
(TX15B).
3.
Install rear propeller shaft. Refer to
.
4.
Check the A/T fluid level and for fluid leakage. Refer to
"Checking the Automatic Transmission Fluid (ATF)"
.
SCIA5254E
Tool number
: ST33400001 (J-26082)
WCIA0475E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст