Nissan Pathfinder (2005 year). Instruction — part 404
AUTOMATIC DRIVE POSITIONER
SE-27
C
D
E
F
G
H
J
K
L
M
A
B
SE
2005 Pathfinder
WIWA0564E
SE-28
AUTOMATIC DRIVE POSITIONER
2005 Pathfinder
Terminals and Reference Values for BCM
EIS00457
Terminals and Reference Values for Driver Seat Control Unit
EIS00458
TERMINAL
WIRE
COLOR
ITEM
CONDITION
VOLTAGE (V)
(Approx.)
11
G/B
Ignition switch (ACC or ON)
Ignition switch (ACC or ON position)
Battery voltage
38
W/R
Ignition switch (ON or START)
Ignition switch (ON or START posi-
tion)
Battery voltage
39
L
CAN-H
—
—
40
P
CAN-L
—
—
47
GR
Front door switch LH
ON (Open)
→
OFF (Closed)
0
→
Battery voltage
67
B
Ground
—
0
70
W
Battery power supply
—
Battery voltage
TERMINAL
WIRE
COLOR
ITEM
CONDITION
VOLTAGE (V)
(Approx.)
1
R
UART LINE (RX)
Pedal adjusting switch ON (FOR-
WARD or BACKWARD operation)
3
L
CAN-H
—
—
6
BR/W
Ignition switch (START)
Ignition switch (START position)
Battery voltage
9
L/R
Reclining motor sensor signal
ON (seat reclining motor opera-
tion)
Other than above
0 or 5
10
W
Rear lifting motor sensor signal
ON (rear lifting motor operation)
Other than above
0 or 5
11
R/B
Sliding switch BACKWARD sig-
nal
ON (seat sliding switch BACK-
WARD operation)
0
Other than above
Battery voltage
12
O/B
Reclining switch BACKWARD
signal
ON (seat reclining switch BACK-
WARD operation)
0
Other than above
Battery voltage
13
L/B
Front lifting switch DOWN signal
ON (front lifting switch DOWN
operation)
0
Other than above
Battery voltage
PIIA4813E
SIIA0692J
SIIA0693J
AUTOMATIC DRIVE POSITIONER
SE-29
C
D
E
F
G
H
J
K
L
M
A
B
SE
2005 Pathfinder
14
G/W
Rear lifting switch DOWN signal
ON (rear lifting switch DOWN
operation)
0
Other than above
Battery voltage
15
L
Pedal adjusting switch BACK-
WARD signal
ON (pedal adjusting switch BACK-
WARD operation)
0
Other than above
Battery voltage
16
W
Seat sensor power
Ignition switch ON
5
17
R/W
UART LINE (TX)
Pedal adjusting switch ON (FOR-
WARD or BACKWARD operation)
19
P
CAN-L
—
—
21
L
A/T device (detent switch) signal
A/T selector lever in P position
0
A/T selector lever other than P
position with ignition key in ignition
cylinder
Battery voltage
24
Y/G
Seat sliding motor sensor signal
ON (seat sliding motor operation)
Other than above
0 or 5
25
LG
Front lifting motor sensor signal
ON (front lifting motor operation)
Other than above.
0 or 5
26
P/B
Seat sliding switch FORWARD
signal
ON (seat sliding switch FOR-
WARD operation)
0
Other than above
Battery voltage
27
G/B
Seat reclining switch FOR-
WARD signal
ON (seat reclining switch FOR-
WARD operation)
0
Other than above
Battery voltage
28
Y/B
Front lifting switch UP signal
ON (front lifting switch UP opera-
tion)
0
Other than above
Battery voltage
29
R/W
Rear lifting switch UP signal
ON (rear lifting switch UP opera-
tion)
0
Other than above
Battery voltage
30
L/W
Pedal adjusting switch FOR-
WARD signal
ON (pedal adjusting switch FOR-
WARD operation)
0
Other than above
Battery voltage
TERMINAL
WIRE
COLOR
ITEM
CONDITION
VOLTAGE (V)
(Approx.)
PIIA4814E
PIIA3277E
SIIA0691J
SE-30
AUTOMATIC DRIVE POSITIONER
2005 Pathfinder
Terminals and Reference Values for Automatic Drive Positioner Control Unit
EIS00459
31
L/Y
Sensor ground
—
0
32
B
Ground
—
0
33
W/L
Battery power supply (PTC)
—
Battery voltage
35
V/W
Sliding motor FORWARD out-
put signal
Sliding switch FORWARD opera-
tion (Motor operated)
Battery voltage
Other than above
0
36
Y/G
Reclining motor FORWARD out-
put signal
Reclining switch FORWARD oper-
ation (Motor operated)
Battery voltage
Other than above
0
37
BR
Front lifting motor DOWN output
signal
Front lifting switch DOWN opera-
tion (Motor operated)
Battery voltage
Other than above
0
38
B/W
Rear lifting motor UP output sig-
nal
Rear end lifting switch UP opera-
tion (Motor operated)
Battery voltage
Other than above
0
39
Y
Rear lifting motor DOWN output
signal
Rear end lifting switch DOWN
operation (Motor operated)
Battery voltage
Other than above
0
40
Y/R
Battery power supply
—
Battery voltage
42
O/B
Sliding motor BACKWARD out-
put signal
Sliding switch BACKWARD oper-
ation (Motor operated)
Battery voltage
Other than above
0
44
Y/R
Reclining motor BACKWARD
output signal
Reclining switch BACKWARD
operation (Motor operated)
Battery voltage
Other than above
0
45
GR
Front lifting motor UP output sig-
nal
Front lifting switch UP operation
(Motor operated)
Battery voltage
Other than above
0
48
B
Ground
—
0
TERMINAL
WIRE
COLOR
ITEM
CONDITION
VOLTAGE (V)
(Approx.)
TERMINAL
WIRE
COLOR
ITEM
CONDITION
VOLTAGE (V)
(Approx.)
2
L
Changeover switch RH signal
Changeover switch in RH position
0
Other than above
5
3
SB
Mirror switch UP signal
Mirror switch in UP position
0
Other than above
5
4
V
Mirror switch LEFT signal
Mirror switch in LEFT position
0
Other than above
5
5
R
Mirror sensor (RH vertical) sig-
nal
Mirror motor RH is operated UP or
DOWN
Changes between 3.4 (close to
peak) 0.6 (close to valley)
6
L
Mirror sensor (LH vertical) sig-
nal
Mirror motor LH is operated UP or
DOWN
Changes between 3.4 (close to
peak) 0.6 (close to valley)
8
O
Pedal sensor input signal
Pedal position front end
0.5
Pedal position rear end
4.5
9
LG
Seat memory switch 1 signal
Memory switch 1 ON
0
Memory switch 1 OFF
5
AUTOMATIC DRIVE POSITIONER
SE-31
C
D
E
F
G
H
J
K
L
M
A
B
SE
2005 Pathfinder
10
SB
UART LINE (TX)
Pedal adjusting switch ON (FOR-
WARD or BACKWARD operation)
12
W
Seat memory switch indictor 1
signal
Memory switch 1 ON
0
Memory switch 1 OFF
Battery voltage
13
Y
Seat memory switch indictor 2
signal
Memory switch 2 ON
0
Memory switch 2 OFF
Battery voltage
14
GR
Mirror motor RH UP signal
Mirror motor RH is operated UP
1.5 - Battery voltage
Other than above
0
15
V
Mirror motor RH LEFT signal
Mirror motor RH is operated LEFT
1.5 - Battery voltage
Other than above
0
16
O
Mirror motor LH DOWN signal
Mirror motor LH is operated DOWN
1.5 - Battery voltage
Other than above
0
Mirror motor LH RIGHT signal
Mirror motor LH is operated RIGHT
1.5 - Battery voltage
Other than above
0
18
Y
Changeover switch LH signal
Changeover switch in LH position
0
Other than above
5
19
BR
Mirror switch DOWN signal
Mirror switch in DOWN position
0
Other than above
5
20
GR
Mirror switch RIGHT signal
Mirror switch in RIGHT position
0
Other than above
5
21
P
Mirror sensor (RH horizontal)
signal
Mirror motor RH is operated LEFT
or RIGHT
Changes between 3.4 (close to left
edge) 0.6 (close to right edge)
22
G
Mirror sensor (LH horizontal)
signal
Mirror motor LH is operated LEFT
or RIGHT
Changes between 3.4 (close to left
edge) 0.6 (close to right edge)
24
GR
Seat memory set switch signal
Set switch ON
0
Set switch OFF
5
25
P
Seat memory switch 2 signal
Memory switch 2 ON
0
Memory switch 2 OFF
5
26
G
UART LINE (RX)
Pedal adjusting switch ON (FOR-
WARD or BACKWARD operation)
30
G
Mirror motor RH DOWN signal
Mirror motor RH is operated DOWN
1.5 - Battery voltage
Other than above
0
Mirror motor RH RIGHT signal
Mirror motor RH is operated RIGHT
1.5 - Battery voltage
Other than above
0
31
R
Mirror motor LH UP signal
Mirror motor LH is operated UP
1.5 - Battery voltage
Other than above
0
TERMINAL
WIRE
COLOR
ITEM
CONDITION
VOLTAGE (V)
(Approx.)
PIIA4813E
PIIA4814E
SE-32
AUTOMATIC DRIVE POSITIONER
2005 Pathfinder
Work Flow
EIS0045A
1.
Check the symptom and customer's requests.
2.
Understand the system description. Refer to
.
3.
Perform the preliminary check. Refer to
.
4.
Check the self-diagnosis, results using CONSULT-II. Refer to
SE-36, "CONSULT-II Function (AUTO
.
5.
Repair or replace depending on the self-diagnostic results.
6.
Based on the trouble diagnosis chart, repair or replace the cause of the malfunction. Refer to
.
7.
Does the automatic drive positioner system operate normally?
If it is normal, GO TO 8.
If it is not normal, GO TO 3.
8.
Inspection End.
32
B
Mirror motor LH LEFT signal
Mirror motor LH is operated LEFT
1.5 - Battery voltage
Other than above
0
33
W
Sensor power supply
—
5
34
R
Battery power supply
—
Battery voltage
37
G
Pedal adjust motor FORWARD
signal
Pedal adjust motor FORWARD
operation (Motor operated)
Battery voltage
Other than above
0
39
SB
Battery power supply
—
Battery voltage
40
B
Ground
—
0
41
Y
Sensor ground
—
0
45
BR
Pedal adjust motor BACK-
WARD signal
Pedal adjust motor BACKWARD
operation (Motor operated)
Battery voltage
Other than above
0
48
B
Ground
—
0
TERMINAL
WIRE
COLOR
ITEM
CONDITION
VOLTAGE (V)
(Approx.)
AUTOMATIC DRIVE POSITIONER
SE-33
C
D
E
F
G
H
J
K
L
M
A
B
SE
2005 Pathfinder
Preliminary Check
EIS0045B
SETTING CHANGE FUNCTION
The settings of the automatic driving positioner system can be changed, using CONSULT-II and the display in
the center of the instrument panel.
×
: Applicable –: Not applicable
It is possible to set sliding front seat for entry/exit of vehicle by pressing set switch.
*: Setting of sliding front seat for entry/exit of vehicle is ON at factory-shipment. But if custom settings are reset, setting turns OFF.
NOTE:
After the setting is registered, the new setting is effective, even if the battery is disconnected.
POWER SUPPLY AND GROUND CIRCUIT INSPECTION
1.
CHECK BCM FUSES AND FUSIBLE LINK
Check if any of the following fuses or fusible link for the BCM are blown.
NOTE:
Refer to
SE-11, "Component Parts And Harness Connector Location"
.
OK or NG
OK
>> GO TO 2.
NG
>> If fuse is blown, be sure to eliminate cause of malfunction before installing new fuse. Refer to
11, "Component Parts And Harness Connector Location"
.
Setting item
Content
CONSULT–II
(WORK SUPPORT)
Display unit
Default
setting
Factory
setting
SEAT SLIDE
VOLUME SET
The distance at exiting opera-
tion can be selected from the
following 3 modes.
40 mm
—
×
×
80 mm
—
—
150 mm
—
—
Sliding Front Seat
When Entry/ Exiting
Vehicle
The seat sliding turnout and
return at entry/exit can be
selected: ON (operated)–OFF
(not operated)
ON
ON: Indicator lamp ON
—
×
OFF
OFF: Indicator lamp OFF
×
—
Reset custom settings*
All settings to default.
—
Default: Setting button
ON
—
—
Content
Setting change operation
Indicator LEDs
The seat sliding turnout and
return at entry/exit can be oper-
ated.
Press the set switch for more than 10 seconds
Blinking twice
The seat sliding turnout and
return at entry/exit can be not
operated.
Blinking once
Unit
Power source
Fuse No.
BCM
Battery power supply
g (50A)
ON or START power supply
1 (10A)
ACC or ON power supply
4 (10A)
SE-34
AUTOMATIC DRIVE POSITIONER
2005 Pathfinder
2.
CHECK BCM POWER SUPPLY CIRCUIT
1.
Disconnect BCM.
2.
Check voltage between BCM connector and ground.
OK or NG
OK
>> GO TO 3.
NG
>> Repair or replace the harness.
3.
CHECK BCM GROUND CIRCUIT
1.
Turn ignition switch OFF.
2.
Check continuity between BCM connector M20 terminal 67 and ground.
OK or NG
OK
>> BCM circuit is OK. Check the driver seat control unit.
GO TO 4.
NG
>> Repair or replace the harness.
4.
CHECK CONTROL UNIT FUSES AND FUSIBLE LINK
Check if any of the following fuses or fusible link for the driver seat control unit and automatic drive positioner
control unit are blown.
NOTE:
Refer to
SE-11, "Component Parts And Harness Connector Location"
.
OK or NG
OK
>> GO TO 5.
NG
>> If fuse is blown, be sure to eliminate cause of malfunction before installing new fuse. Refer to
11, "Component Parts And Harness Connector Location"
.
Connector
Terminals
Power
source
Condition
Voltage (V)
(Approx.)
(+)
(–)
M20
70
Ground
Battery
power
supply
Ignition
switch
OFF
Battery voltage
M18
38
Ground
Ignition
power
supply
Ignition
switch
ON or
START
Battery voltage
11
Ground
ACC
power
supply
Ignition
switch
ACC or
ON
Battery voltage
LIIA0995E
67 - Ground
: Continuity should exist.
LIIA0915E
Unit
Power source
Fuse No.
Driver seat control unit and automatic
drive positioner control unit
START power supply
9 (10A)
Battery power supply
22 (10A)
Battery power supply
g (50A)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст