Nissan Pathfinder (2005 year). Instruction — part 36
OVERHAUL
AT-259
D
E
F
G
H
I
J
K
L
M
A
B
AT
2005 Pathfinder
7.
Pawl shaft
8.
Self-sealing bolt
9.
Seal ring
10. Needle bearing
11.
Gasket
12. Revolution sensor
13. Parking gear
14. Output shaft
15. Bearing race
16. Needle bearing
17. Instruction plate
18. Parking rod
19. Instruction shaft oil seal
20. Instruction shaft
21. O-ring
22. Band servo anchor end pin
23. Detent spring
24. Spacer
25. Seal ring
26. Snap ring
27. Return spring
28. O-ring
29. Servo assembly
30. Snap ring
31. Sub-harness
32. Control valve with TCM
33. Bracket
34. A/T fluid temperature sensor 2
35. Oil pan
36. Magnet
37. Drain plug
38. Drain plug gasket
39. Oil pan mounting bolt
40. Oil pan gasket
41. Terminal cord assembly
42. O-ring
43. Retaining pin
44. Transmission case
AT-260
OVERHAUL
2005 Pathfinder
Oil Channel
UCS003Z2
2WD models
SCIA5185E
OVERHAUL
AT-261
D
E
F
G
H
I
J
K
L
M
A
B
AT
2005 Pathfinder
4WD models
SCIA5189E
AT-262
OVERHAUL
2005 Pathfinder
Locations of Adjusting Shims, Needle Bearings, Thrust Washers and Snap
Rings
UCS003Z3
2WD models
SCIA6421E
OVERHAUL
AT-263
D
E
F
G
H
I
J
K
L
M
A
B
AT
2005 Pathfinder
4WD models
SCIA6422E
AT-264
DISASSEMBLY
2005 Pathfinder
DISASSEMBLY
PFP:31020
Disassembly
UCS003Z4
CAUTION:
Do not disassemble parts behind Drum Support. Refer to
.
1.
Drain ATF through drain plug.
2.
Remove torque converter by holding it firmly and turing while
pulling straight out.
3.
Check torque converter one-way clutch using a check tool as
shown at figure.
a.
Insert a check tool into the groove of bearing support built into
one-way clutch outer race.
b.
When fixing bearing support with a check tool, rotate one-way
clutch spline using a screwdriver.
c.
Make sure that inner race rotates clockwise only. If not, replace
torque converter assembly.
4.
Remove converter housing from transmission case.
CAUTION:
Be careful not to scratch converter housing.
SCIA5010E
SCIA3171E
SCIA4634E
DISASSEMBLY
AT-265
D
E
F
G
H
I
J
K
L
M
A
B
AT
2005 Pathfinder
5.
Remove O-ring from input clutch assembly.
6.
Remove tightening bolts for oil pump assembly and transmis-
sion case.
7.
Attach the sliding hammers to oil pump assembly and extract it
evenly from transmission case.
CAUTION:
●
Fully tighten the sliding hammer screws.
●
Make sure that bearing race is installed to the oil pump
assembly edge surface.
8.
Remove O-ring from oil pump assembly.
SCIA5011E
SCIA2300E
SCIA5474E
SCIA5172E
AT-266
DISASSEMBLY
2005 Pathfinder
9.
Remove bearing race from oil pump assembly.
10. Remove needle bearing from front sun gear.
11. Remove front sun gear assembly from front carrier assembly.
NOTE:
Remove front sun gear by rotating left/right.
12. Remove seal rings from input clutch assembly.
13. Remove front carrier assembly from rear carrier assembly. (With
input clutch assembly and rear internal gear.)
CAUTION:
Be careful to remove it with needle bearing.
SCIA6529E
SCIA2808E
SCIA5014E
SCIA2470E
SCIA5015E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст