Nissan Pathfinder (2005 year). Instruction — part 152
ON BOARD DIAGNOSTIC (OBD) SYSTEM
EC-67
C
D
E
F
G
H
I
J
K
L
M
A
EC
2005 Pathfinder
RELATIONSHIP BETWEEN MIL, DTC, 1ST TRIP DTC AND DRIVING PATTERNS FOR “MISFIRE
” <EXHAUST QUALITY DETERIORATION>, “FUEL INJECTION SYSTEM”
*1: When the same malfunction is
detected in two consecutive trips,
MIL will light up.
*2: MIL will go off after vehicle is driven
3 times (pattern B) without any mal-
functions.
*3: When the same malfunction is
detected in two consecutive trips, the
DTC and the freeze frame data will
be stored in ECM.
*4: The DTC and the freeze frame data
will not be displayed any longer after
vehicle is driven 80 times (pattern C)
without the same malfunction. (The
DTC and the freeze frame data still
remain in ECM.)
*5: When a malfunction is detected for
the first time, the 1st trip DTC and
the 1st trip freeze frame data will be
stored in ECM.
*6: The 1st trip DTC and the 1st trip
freeze frame data will be cleared at
the moment OK is detected.
*7: When the same malfunction is
detected in the 2nd trip, the 1st trip
freeze frame data will be cleared.
*8: 1st trip DTC will be cleared when
vehicle is driven once (pattern C)
without the same malfunction after
DTC is stored in ECM.
SEF392S
EC-68
ON BOARD DIAGNOSTIC (OBD) SYSTEM
2005 Pathfinder
EXPLANATION FOR DRIVING PATTERNS FOR “MISFIRE <EXHAUST QUALITY DETERIORA-
TION>”, “FUEL INJECTION SYSTEM”
<Driving Pattern B>
Driving pattern B means the vehicle operation as follows:
All components and systems should be monitored at least once by the OBD system.
●
The B counter will be cleared when the malfunction is detected once regardless of the driving pattern.
●
The B counter will be counted up when driving pattern B is satisfied without any malfunction.
●
The MIL will go off when the B counter reaches 3. (*2 in “OBD SYSTEM OPERATION CHART”)
<Driving Pattern C>
Driving pattern C means the vehicle operation as follows:
The following conditions should be satisfied at the same time:
Engine speed: (Engine speed in the freeze frame data)
±
375 rpm
Calculated load value: (Calculated load value in the freeze frame data) x (1
±
0.1) [%]
Engine coolant temperature (T) condition:
●
When the freeze frame data shows lower than 70
°
C (158
°
F), T should be lower than 70
°
C (158
°
F).
●
When the freeze frame data shows higher than or equal to 70
°
C (158
°
F), T should be higher than or equal
to 70
°
C (158
°
F).
Example:
If the stored freeze frame data is as follows:
Engine speed: 850 rpm, Calculated load value: 30%, Engine coolant temperature: 80
°
C (176
°
F)
To be satisfied with driving pattern C, the vehicle should run under the following conditions:
Engine speed: 475 - 1,225 rpm, Calculated load value: 27 - 33%, Engine coolant temperature: more than 70
°
C
(158
°
F)
●
The C counter will be cleared when the malfunction is detected regardless of vehicle conditions above.
●
The C counter will be counted up when vehicle conditions above is satisfied without the same malfunction.
●
The DTC will not be displayed after C counter reaches 80.
●
The 1st trip DTC will be cleared when C counter is counted once without the same malfunction after DTC
is stored in ECM.
ON BOARD DIAGNOSTIC (OBD) SYSTEM
EC-69
C
D
E
F
G
H
I
J
K
L
M
A
EC
2005 Pathfinder
RELATIONSHIP BETWEEN MIL, DTC, 1ST TRIP DTC AND DRIVING PATTERNS EXCEPT FOR
“MISFIRE <EXHAUST QUALITY DETERIORATION>”, “FUEL INJECTION SYSTEM”
*1: When the same malfunction is
detected in two consecutive trips,
MIL will light up.
*2: MIL will go off after vehicle is driven
3 times (pattern B) without any mal-
functions.
*3: When the same malfunction is
detected in two consecutive trips, the
DTC and the freeze frame data will
be stored in ECM.
*4: The DTC and the freeze frame data
will not be displayed any longer after
vehicle is driven 40 times (pattern A)
without the same malfunction.
(The DTC and the freeze frame data
still remain in ECM.)
*5: When a malfunction is detected for
the first time, the 1st trip DTC and
the 1st trip freeze frame data will be
stored in ECM.
*6: 1st trip DTC will be cleared after
vehicle is driven once (pattern B)
without the same malfunction.
*7: When the same malfunction is
detected in the 2nd trip, the 1st trip
freeze frame data will be cleared.
SEF393SD
EC-70
ON BOARD DIAGNOSTIC (OBD) SYSTEM
2005 Pathfinder
EXPLANATION FOR DRIVING PATTERNS EXCEPT FOR “MISFIRE <EXHAUST QUALITY
DETERIORATION>”, “FUEL INJECTION SYSTEM”
<Driving Pattern A>
●
The A counter will be cleared when the malfunction is detected regardless of (1) - (4).
●
The A counter will be counted up when (1) - (4) are satisfied without the same malfunction.
●
The DTC will not be displayed after the A counter reaches 40.
<Driving Pattern B>
Driving pattern B means the vehicle operation as follows:
All components and systems should be monitored at least once by the OBD system.
●
The B counter will be cleared when the malfunction is detected once regardless of the driving pattern.
●
The B counter will be counted up when driving pattern B is satisfied without any malfunctions.
●
The MIL will go off when the B counter reaches 3 (*2 in OBD SYSTEM OPERATION CHART).
AEC574
BASIC SERVICE PROCEDURE
EC-71
C
D
E
F
G
H
I
J
K
L
M
A
EC
2005 Pathfinder
BASIC SERVICE PROCEDURE
PFP:00018
Basic Inspection
UBS00K3V
1.
INSPECTION START
1.
Check service records for any recent repairs that may indicate a related malfunction, or a current need for
scheduled maintenance.
2.
Open engine hood and check the following:
–
Harness connectors for improper connections
–
Wiring harness for improper connections, pinches and cut
–
Vacuum hoses for splits, kinks and improper connections
–
Hoses and ducts for leaks
–
Air cleaner clogging
–
Gasket
3.
Confirm that electrical or mechanical loads are not applied.
–
Headlamp switch is OFF.
–
Air conditioner switch is OFF.
–
Rear window defogger switch is OFF.
–
Steering wheel is in the straight-ahead position, etc.
4.
Start engine and warm it up until engine coolant temperature
indicator points the middle of gauge.
Ensure engine stays below 1,000 rpm.
5.
Run engine at about 2,000 rpm for about 2 minutes under no-
load.
6.
Make sure that no DTC is displayed with CONSULT-II or GST.
OK or NG
OK
>> GO TO 3.
NG
>> GO TO 2.
2.
REPAIR OR REPLACE
Repair or replace components as necessary according to corresponding Diagnostic Procedure.
>> GO TO 3.
SEF983U
SEF976U
SEF977U
EC-72
BASIC SERVICE PROCEDURE
2005 Pathfinder
3.
CHECK TARGET IDLE SPEED
With CONSULT-II
1.
Run engine at about 2,000 rpm for about 2 minutes under no-load.
2.
Rev engine (2,000 to 3,000 rpm) two or three times under no-
load, then run engine at idle speed for about 1 minute.
3.
Read idle speed in “DATA MONITOR” mode with CONSULT-II.
Refer to
.
Without CONSULT-II
1.
Run engine at about 2,000 rpm for about 2 minutes under no-load.
2.
Rev engine (2,000 to 3,000 rpm) two or three times under no-load, then run engine at idle speed for about
1 minute.
3.
Check idle speed. Refer to
.
OK or NG
OK
>> GO TO 9.
NG
>> GO TO 4.
4.
PERFORM ACCELERATOR PEDAL RELEASED POSITION LEARNING
1.
Stop engine.
2.
Perform
EC-88, "Accelerator Pedal Released Position Learning"
.
>> GO TO 5.
5.
PERFORM THROTTLE VALVE CLOSED POSITION LEARNING
Perform
EC-88, "Throttle Valve Closed Position Learning"
.
>> GO TO 6.
PBIA8513J
625
±
50 rpm (in P or N position)
SEF058Y
625
±
50 rpm (in P or N position)
BASIC SERVICE PROCEDURE
EC-73
C
D
E
F
G
H
I
J
K
L
M
A
EC
2005 Pathfinder
6.
PERFORM IDLE AIR VOLUME LEARNING
Refer to
EC-89, "Idle Air Volume Learning"
.
Is Idle Air Volume Learning carried out successfully?
Yes or No
Yes
>> GO TO 7.
No
>> 1. Follow the instruction of Idle Air Volume Learning.
2. GO TO 4.
7.
CHECK TARGET IDLE SPEED AGAIN
With CONSULT-II
1.
Start engine and warm it up to normal operating temperature.
2.
Read idle speed in “DATA MONITOR” mode with CONSULT-II.
Refer to
.
Without CONSULT-II
1.
Start engine and warm it up to normal operating temperature.
2.
Check idle speed.
Refer to
.
OK or NG
OK
>> GO TO 10.
NG
>> GO TO 8.
8.
DETECT MALFUNCTIONING PART
Check the following.
●
Check camshaft position sensor (PHASE) and circuit. Refer to
.
●
Check crankshaft position sensor (POS) and circuit. Refer to
.
OK or NG
OK
>> GO TO 9.
NG
>> 1. Repair or replace.
2. GO TO 4.
9.
CHECK ECM FUNCTION
1.
Substitute another known-good ECM to check ECM function. (ECM may be the cause of an incident, but
this is a rare case.)
2.
Perform initialization of NVIS (NATS) system and registration of all NVIS (NATS) ignition key IDs. Refer to
EC-47, "NVIS (NISSAN VEHICLE IMMOBILIZER SYSTEM-NATS)"
.
>> GO TO 4.
625
±
50 rpm (in P or N position)
625
±
50 rpm (in P or N position)
SEF174Y
EC-74
BASIC SERVICE PROCEDURE
2005 Pathfinder
10.
CHECK IGNITION TIMING
1.
Run engine at idle.
2.
Check ignition timing with a timing light. Refer to
.
OK or NG
OK
>> GO TO 19.
NG
>> GO TO 11.
11.
PERFORM ACCELERATOR PEDAL RELEASED POSITION LEARNING
1.
Stop engine.
2.
Perform
EC-88, "Accelerator Pedal Released Position Learning"
.
>> GO TO 12.
12.
PERFORM THROTTLE VALVE CLOSED POSITION LEARNING
Perform
EC-88, "Throttle Valve Closed Position Learning"
.
>> GO TO 13.
13.
PERFORM IDLE AIR VOLUME LEARNING
Refer to
EC-89, "Idle Air Volume Learning"
.
Is Idle Air Volume Learning carried out successfully?
Yes or No
Yes
>> GO TO 14.
No
>> 1. Follow the instruction of Idle Air Volume Learning.
2. GO TO 4.
14.
CHECK TARGET IDLE SPEED AGAIN
With CONSULT-II
1.
Start engine and warm it up to normal operating temperature.
2.
Read idle speed in “DATA MONITOR” mode with CONSULT-II.
Refer to
.
Without CONSULT-II
1.
Start engine and warm it up to normal operating temperature.
2.
Check idle speed. Refer to
.
OK or NG
OK
>> GO TO 15.
NG
>> GO TO 17.
15
±
5
°
BTDC (in P or N position)
BBIA0531E
625
±
50 rpm (in P or N position)
625
±
50 rpm (in P or N position)
SEF174Y
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст