Nissan X-Trail 32. Instruction — part 700
STRUCTURE AND OPERATION
DLN-211
< SYSTEM DESCRIPTION >
[REAR PROPELLER SHAFT: C-CVJ-C]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
SYSTEM DESCRIPTION
STRUCTURE AND OPERATION
Sectional View
INFOID:0000000010822156
PART OF JOINT
Universal Type (Shell Type)
CVJ Type
JSDIA4709ZZ
JSDIA5322ZZ
DLN-212
< SYMPTOM DIAGNOSIS >
[REAR PROPELLER SHAFT: C-CVJ-C]
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
SYMPTOM DIAGNOSIS
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
NVH Troubleshooting Chart
INFOID:0000000010822157
Use the chart below to find the cause of the symptom. If necessary, repair or replace these parts.
×
: Applicable
Reference
NVH of REAR FINAL
DR
IVE in this section.
NVH in F
AX, RAX
, FS
U,
an
d RS
U
se
ct
ion
.
NVH in WT
se
ct
io
n.
NVH in WT
se
ct
io
n.
NVH in F
AX and RAX section.
NVH in BR section.
NVH in ST
section.
Possible cause and SUSPECTED PARTS
Un
ev
en
rot
a
ti
ng
to
rq
ue
Ce
nt
e
r be
ari
n
g
im
pro
p
e
r
in
st
al
la
ti
on
Exc
e
s
s
ive
c
e
n
ter
be
arin
g
ax
ia
l e
n
d
pl
ay
Ce
nt
e
r be
ari
n
g
mou
n
ti
n
g
(in
s
u
lat
or) c
rack
s
, da
ma
ge
or de
te
ri
ora
tio
n
Ex
ce
ssi
v
e
jo
in
t an
gl
e
Ro
ta
ti
on
i
m
ba
la
nc
e
Ex
ce
ssi
v
e
run
o
u
t
DIFFERENTIAL
AXLE
AND SUSPE
N
S
ION
TIRE
ROA
D
WHEEL
DR
IVE SHAF
T
BRAKE
STEERING
Symptom
Noise
×
×
×
×
×
×
×
×
×
×
×
×
×
×
Shake
×
×
×
×
×
×
×
×
Vibration
×
×
×
×
×
×
×
×
×
×
×
REAR PROPELLER SHAFT
DLN-213
< PERIODIC MAINTENANCE >
[REAR PROPELLER SHAFT: C-CVJ-C]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
PERIODIC MAINTENANCE
REAR PROPELLER SHAFT
Inspection
INFOID:0000000010822158
LOOSENESS OF CONNECTED PART
Check each fixing bolt and nut for looseness using torque wrench. For each tightening torque, refer to
BACKLASH OF JOINT PART
Move the joint of propeller shaft up and down and from side to side
(axial direction of shaft and right angle to shaft) to check that the joint
has no backlash. If the joint has a malfunction, remove propeller
shaft and perform inspection.
BACKLASH OF CENTER BEARING
Move the shaft near center bearing up and down and from side to
side (axial direction of shaft and right angle to shaft) to check that the
bearing has no backlash. If the bearing has a malfunction, remove
propeller shaft and perform inspection.
APPEARANCE AND NOISE
• Check the propeller shaft tube surface for dents or cracks. If malfunction is detected, replace propeller shaft
assembly.
• If center bearing is noisy or damaged, replace propeller shaft assembly.
VIBRATION
If vibration is present at high speed, adjust the propeller shaft phase first.
1.
Check the propeller shaft for bend and damage. If damaged, replace propeller shaft assembly.
2.
Perform a cruise test drive to check the propeller shaft for runout. If vibration occurs, separate propeller
shaft at final drive companion flange; then change the phase between electric controlled coupling stud bolt
and propeller shaft by the one bolt hole at a time and install propeller shaft.
3.
If vibration is still detected, measure propeller shaft runout after removing it. Refer to
MAA0555D
MAA0005D
DLN-214
< REMOVAL AND INSTALLATION >
[REAR PROPELLER SHAFT: C-CVJ-C]
REAR PROPELLER SHAFT
REMOVAL AND INSTALLATION
REAR PROPELLER SHAFT
Exploded View
INFOID:0000000010822159
Removal and Installation
INFOID:0000000010822160
REMOVAL
1.
Shift transaxle to the neutral position, and then release parking brake.
2.
Remove mounting rubber
of main muffler. Refer to
(QR25DE),
EX-18, "Removal and Installation"
(R9M).
CAUTION:
Remove only near the center bearing mounting bracket of
propeller shaft.
Center bearing mounting bracket
(upper)
Clip
Propeller shaft assembly
Center bearing mounting bracket
(lower)
: Vehicle front
: N·m (kg-m, ft-lb)
: Always replace after every disassembly.
JSDIA5323GB
JSDIA5464ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст