Nissan X-Trail 32. Instruction — part 2066
TM-222
< UNIT DISASSEMBLY AND ASSEMBLY >
[6MT: RS6F52A]
FINAL DRIVE
Gear, Washer, Shaft, and Case
Check side gears, side gear thrust washers, pinion mate shaft, pin-
ion mate gears, pinion mate thrust washers and differential case. If
necessary, replace with a new one.
Output Gear and Reduction Gear
Check output gear and reduction gear. If necessary, replace with a new one.
Bearing
Check for bearings damage and rough rotation. If necessary, replace
with a new one.
CAUTION:
When replacing tapered roller bearing, replace outer and inner
races as a set.
MTK0135D
SPD715
SERVICE DATA AND SPECIFICATIONS (SDS)
TM-223
< SERVICE DATA AND SPECIFICATIONS (SDS)
[6MT: RS6F52A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
General Specifications
INFOID:0000000010921117
Applied model
Axle
2WD
4WD
Engine
R9M
Transaxle model
RS6F52A
Number of speed
6
Synchromesh type
Warner
Shift pattern
Gear ratio
1st
3.727
2nd
2.043
3rd
1.322
4th
0.947
5th
0.723
6th
0.596
Reverse
3.641
Final gear
4.428
Number of teeth
Input gear
1st
11
2nd
23
3rd
31
4th
38
5th
47
6th
52
Reverse
11
Main gear
1st
41
2nd
47
3rd
41
4th
36
5th
34
6th
31
Reverse
39
Reverse idler gear
Front/Rear (Input/Output)
37/38
Final gear
Final gear/Pinion
62/14
Side gear/Pinion mate gear
13/10
Oil level
43.0 – 48.0 mm
(1.693 – 1.890 in)
87.0 – 92.0 mm
(3.425 – 3.622 in)
Oil capacity (Reference)
MA-23, "Fluids and Lubricants"
.
PCIB1769E
TM-224
< SERVICE DATA AND SPECIFICATIONS (SDS)
[6MT: RS6F52A]
SERVICE DATA AND SPECIFICATIONS (SDS)
End Play
INFOID:0000000010919435
Unit: mm (in)
Baulk Ring Clearance
INFOID:0000000010919436
Unit: mm (in)
Remarks
Reverse synchronizer
Installed
Double-cone synchronizer
3rd
Triple-cone synchronizer
1st and 2nd
Applied model
Axle
2WD
4WD
Engine
R9M
Transaxle model
RS6F52A
Item
Standard
Input gear
3rd
0.18 – 0.31 (0.0071 – 0.0122)
4th
0.20 – 0.30 (0.0079 – 0.0118)
5th
0.06 – 0.16 (0.0024 – 0.0063)
6th
0.06 – 0.16 (0.0024 – 0.0063)
Main gear
1st
0.20 – 0.30 (0.0079 – 0.0118)
2nd
0.06 – 0.16 (0.0024 – 0.0063)
6th
0 – 0.1 (0 – 0.004)
Reverse idler gear
0.04 – 0.10 (0.0016 – 0.0039)
6th input gear bushing
0 – 0.1 (0 – 0.004)
Input shaft
0 – 0.06 (0 – 0.0024)
Mainshaft
0 – 0.06 (0 – 0.0024)
Mainshaft C-ring
0 – 0.06 (0 – 0.0024)
Striking rod
0.05 – 0.152 (0.0020 – 0.0060)
Output gear bearing (For 4WD only)
0 – 0.06 (0 – 0.0024)
Output gear assembly (For 4WD only)
0 – 0.06 (0 – 0.0024)
Measurement point
Standard
Limit
3rd
(Double-cone synchronizer)
Clearance (A) between synchronizer cone
and inner baulk ring end face
0.6 – 0.8 (0.024 – 0.031)
0.2 (0.008)
Clearance (B) between outer baulk ring
pawl and synchronizer cone
0.6 – 1.1 (0.024 –0.043)
0.2 (0.008)
1st and 2nd
(Triple-cone synchronizer)
Clearance (A) between synchronizer cone
and clutch gear end face
0.6 – 1.2 (0.024 – 0.047)
0.3 (0.012)
Clearance (B) between outer baulk ring
pawl and synchronizer cone
0.6 – 1.1 (0.024 – 0.043)
0.2 (0.008)
Clearance (C) between inner baulk ring and
clutch gear end face
0.7 – 1.1 (0.028 – 0.043)
0.3 (0.012)
4th
0.9 – 1.45 (0.035 – 0.057)
0.7 (0.028)
5th
0.95 – 1.4 (0.037 – 0.055)
0.7 (0.028)
PCIB0249E
PCIB0835J
SERVICE DATA AND SPECIFICATIONS (SDS)
TM-225
< SERVICE DATA AND SPECIFICATIONS (SDS)
[6MT: RS6F52A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
Dimension
INFOID:0000000010919437
INPUT SHAFT
Unit: mm (in)
MAINSHAFT
Unit: mm (in)
SHIFT FORK
Unit: mm (in)
6th
0.95 – 1.4 (0.037 – 0.055)
0.7 (0.028)
Reverse
0.95 – 1.4 (0.037 – 0.055)
0.7 (0.028)
Measurement point
Standard
Limit
Measurement point
Standard
Dimension (C2) between mounting face of
input shaft front bearing and thrust washer
end face
161.8 – 161.9 (6.370 – 6.374)
JPDIC0364ZZ
Measurement point
Standard
Dimension (C1) between mounting face of
mainshaft front bearing and 4th main gear
adjusting shim end face
182.85 – 182.95 (7.199 – 7.203)
JPDIC0363ZZ
Measurement point
One-side wear specification
Sliding width of new part
1st-2nd
0.2 (0.008)
7.80 – 7.93 (0.3071 – 0.3122)
3rd-4th
0.2 (0.008)
7.80 – 7.93 (0.3071 – 0.3122)
5th-6th
0.2 (0.008)
6.10 – 6.23 (0.2402 – 0.2453)
Reverse
0.2 (0.008)
12.80 – 12.93 (0.5039 – 0.5091)
SMT801D
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст