Nissan X-Trail 32. Instruction — part 566
HOOD LOCK
DLK-605
< REMOVAL AND INSTALLATION >
[TYPE 2]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
HOOD LOCK
Exploded View
INFOID:0000000010728147
HOOD LOCK
HOOD LOCK : Removal and Installation
INFOID:0000000010728148
REMOVAL
1.
Disconnect hood lock switch harness connector
(if equipped).
Hood lock assembly
Hood lock bell crank assembly
Hood lock control cable assembly
Hood lock control handle assembly
Cable clip
: N·m (kg-m, in-lb)
: Body grease
JMKIB3484GB
: Vehicle front
JMKIB2974ZZ
DLK-606
< REMOVAL AND INSTALLATION >
[TYPE 2]
HOOD LOCK
2.
Disconnect hood lock bell crank cable from hood lock assembly. Refer to
CRANK : Removal and Installation"
.
3.
Remove hood lock assembly mounting bolts, and then remove hood lock assembly.
4.
Disconnect hood lock control cable assembly
from hood lock
assembly
according to the numerical order 1
→
2 indicated by
arrows as shown in the figure.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• Never bend cable too much, keeping the radius 100 mm (3.937 in) or more.
• Check that hood lock control cable is properly engaged with hood lock.
• After installation, perform hood fitting adjustment. Refer to
DLK-567, "HOOD ASSEMBLY : Adjust-
• After installation, perform hood lock control inspection. Refer to
.
HOOD LOCK : Inspection
INFOID:0000000010728149
NOTE:
If the hood lock cable is bent or deformed, replace it.
1.
Check that hood opener operating is condition 49 N (5.0 kg, 11.0 lb) or below.
2.
Check that secondary latch
is securely engaged with second-
ary striker
from the dead load of hood assembly.
3.
Check that primary latch
is securely engaged with primary
striker
when hood assembly is closed [free-fall from approxi-
mately 200 mm (7.874 in) height].
4.
While operating the hood opener carefully, check that the front end of the hood is lifted by approximately
20 mm (0.787 in) (A). Also, check that the hood opener returns to the original position.
JMKIB3486ZZ
JMKIB3518ZZ
JMKIB3499ZZ
HOOD LOCK
DLK-607
< REMOVAL AND INSTALLATION >
[TYPE 2]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
5.
Check that secondary latch is properly engaged with secondary striker [6.8 mm (0.268 in)] (B).
6.
Check the hood lock lubrication condition. If necessary, apply body grease to hood lock.
• Hood lock assembly
• Hood lock bell crank assembly
HOOD LOCK CONTROL HANDLE
HOOD LOCK CONTROL HANDLE : Removal and Installation
INFOID:0000000010728150
REMOVAL
1.
Remove hood lock control handle mounting bolts, and then remove hood lock control handle.
2.
Remove hood lock control cable
from hood opener lever
according to the numerical order 1
→
2 indicated by arrows as
shown in the figure.
Secondary striker
Secondary latch
Primary striker
Primary latch
JMKIB3549ZZ
: Body grease
JMKIB2979ZZ
: Body grease
JMKIB2980ZZ
JMKIB0324ZZ
DLK-608
< REMOVAL AND INSTALLATION >
[TYPE 2]
HOOD LOCK
3.
Remove fuel filler lid opener cable from fuel filler lid opener lever. Refer to
OPENER CABLE : Removal and Installation"
.
INSTALLATION
Note the following item, and install in the reverse order of removal.
CAUTION:
After installation, perform hood lock control inspection. Refer to
DLK-606, "HOOD LOCK : Inspection"
.
HOOD LOCK CONTROL CABLE
HOOD LOCK CONTROL CABLE : Removal and Installation
INFOID:0000000010728151
REMOVAL
1.
Remove air duct 1. Refer to
EM-31, "Removal and Installation"
(QR25DE) or
EM-308, "Removal and Installation"
(R9M).
2.
Disconnect hood lock control cable assembly from hood lock assembly. Refer to
.
3.
Remove fender protector LH. Refer to
EXT-35, "FENDER PROTECTOR : Removal and Installation"
.
4.
Remove hood lock control cable fixing clips.
5.
Disconnect hood lock control cable assembly from hood lock control handle. Refer to
LOCK CONTROL HANDLE : Removal and Installation"
.
6.
Remove dash side finisher LH. Refer to
INT-26, "DASH SIDE FINISHER : Removal and Installation"
.
7.
Remove grommet of the lower dash, and pull the hood lock control cable assembly toward inside vehicle.
CAUTION:
While pulling, never damage (peeling) the outside of hood lock control cable.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• Never bend cable too much, keeping the radius 100 mm (3.937 in) or more.
• Install grommet in the panel hole surely.
• Check that cable is not offset from the positioning grommet,
and apply the sealant to the grommet
properly.
• After installation, perform hood lock control inspection. Refer to
.
HOOD LOCK BELL CRANK
HOOD LOCK BELL CRANK : Removal and Installation
INFOID:0000000010728152
REMOVAL
JMKIA5814ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст