Nissan X-Trail 32. Instruction — part 1634
PB-62
< BASIC INSPECTION >
OPERATION OF REAR BRAKE CALIPER
• Never operate the parking brake switch.
• Never depress the brake pedal.
2.
Touch “START”.
>> GO TO 3.
3.
PERFORM THE SELF-DIAGNOSIS
With CONSULT
1.
Pull parking brake switch to activate electric parking brake.
2.
Push parking brake switch to release electric parking brake.
3.
Perform “EHS/PKB” self-diagnosis.
Is malfunction detected?
YES
>> Check the DTC. Refer to
. GO TO 4.
NO
>> GO TO 4.
4.
CHECK DATA MONITOR
With CONSULT
Select “EHS/PKB”, “DATA MONITOR”, “BR FORCE EST (LH)” and “BR FORCE EST (RH)” according to this
order. Check that signals are within the specified value. Refer to
.
Is the check result normal?
YES
>> GO TO 5.
NO
>> GO TO 1.
5.
ERASE SELF-DIAGNOSIS MEMORY
With CONSULT
1.
Turn the ignition switch OFF to ON.
CAUTION:
Be sure to wait for 10 seconds or more after turning the ignition switch OFF or ON.
2.
Erase self-diagnosis results memory of “EHS/PKB”.
Is the memory erased?
YES
>> INSPECTION END
NO
>> Check the items indicated by the self-diagnosis.
RELEASE OF REAR BRAKE CALIPER
PB-63
< BASIC INSPECTION >
C
D
E
G
H
I
J
K
L
M
A
B
PB
N
O
P
RELEASE OF REAR BRAKE CALIPER
Description
INFOID:0000000010722948
CAUTION:
When the following operations are performed, always use CONSULT, for performing “BRAKE
RELEASE” of “WORK SUPPORT”.
×
: Required
—: not required
*: M/T models
Work Procedure
INFOID:0000000010722949
CAUTION:
When the following operations are performed, always use CONSULT. (It cannot be performed by any
means other than CONSULT.)
• Removing/installing electric parking brake control module
• Replacing electric parking brake control module
• Removing/installing rear brake pad (When not pressing piston of rear brake caliper assembly)
• Removing/installing rear brake pad (When pressing piston of rear brake caliper assembly)
• Replacing rear brake pad
• Removing/installing rear brake caliper assembly
• Replacing rear brake caliper assembly
NOTE:
When the replaced rear brake pad, refer to
1.
PERFORM BRAKE OPERATION
With CONSULT
1.
Select “EHS/PKB”, “WORK SUPPORT”, and “BRAKE OPERATION” according to this order.
CAUTION:
• Never operate the parking brake switch.
• Never depress the brake pedal.
2.
Touch “START”.
>> GO TO 2.
2.
PERFORM BRAKE RELEASE
With CONSULT
1.
Select “EHS/PKB”, “WORK SUPPORT”, and “BRAKE RELEASE” according to this order.
CAUTION:
Procedure
BRAKE RELEASE
Removing/installing electric parking brake control module
×
Replacing electric parking brake control module
×
Removing/installing rear brake pad (When not pressing piston of rear
brake caliper assembly)
×
Removing/installing rear brake pad (When pressing piston of rear brake
caliper assembly)
×
Replacing rear brake pad
×
Removing/installing rear brake caliper assembly
×
Replacing rear brake caliper assembly
×
Removing/installing parking brake switch
—
Replacing parking brake switch
—
Removing/installing clutch stroke sensor
*
—
Replacing clutch stroke sensor
*
—
Removing/installing clutch pedal
*
—
Replacing clutch pedal
*
—
PB-64
< BASIC INSPECTION >
RELEASE OF REAR BRAKE CALIPER
• Never operate the parking brake switch.
• Never depress the brake pedal.
2.
Touch “START”.
>> GO TO 3.
3.
PERFORM THE SELF-DIAGNOSIS
With CONSULT
1.
Pull parking brake switch to activate electric parking brake.
2.
Push parking brake switch to release electric parking brake.
3.
Perform “EHS/PKB” self-diagnosis.
Is malfunction detected?
YES
>> Check the DTC. Refer to
. GO TO 4.
NO
>> GO TO 4.
4.
CHECK DATA MONITOR
With CONSULT
Select “EHS/PKB”, “DATA MONITOR”, “BR FORCE EST (LH)”, and “BR FORCE EST (RH)” according to this
order. Check that signals are within the specified value. Refer to
.
Is the check result normal?
YES
>> GO TO 5.
NO
>> GO TO 1.
5.
ERASE SELF-DIAGNOSIS MEMORY
With CONSULT
1.
Turn the ignition switch OFF to ON.
CAUTION:
Be sure to wait for 10 seconds or more after turning the ignition switch OFF or ON.
2.
Erase self-diagnosis results memory of “EHS/PKB”.
Is the memory erased?
YES
>> INSPECTION END
NO
>> Check the items indicated by the self-diagnosis.
CHANGE OF SYSTEM MODE
PB-65
< BASIC INSPECTION >
C
D
E
G
H
I
J
K
L
M
A
B
PB
N
O
P
CHANGE OF SYSTEM MODE
Description
INFOID:0000000010722950
CAUTION:
When the following operations are performed, always use CONSULT, for performing “SYSTEM MODE
CHANGE” of “WORK SUPPORT”.
×
: Required
—: not required
*: M/T models
Work Procedure
INFOID:0000000010722951
CAUTION:
When performing the following operations, always use CONSULT. (It cannot be performed by any
means other than CONSULT.)
• Replacing electric parking brake control module
1.
CONFIGURATION
Perform the configuration. Refer to
.
>> GO TO 2.
2.
CALIBRATION OF G SENSOR
Perform the calibration of G sensor. Refer to
.
M/T models>>GO TO 3.
CVT models>>GO TO 4.
3.
RESET OF CLUTCH PEDAL STROKE SENSOR (M/T MODELS)
Perform the reset of clutch stroke sensor. Refer to
>> GO TO 4.
4.
ADJUSTMENT OF REAR BRAKE CALIPER INITIAL POSITION
Perform the adjustment of rear brake caliper initial position: Refer to
>> GO TO 5.
5.
OPERATION OF REAR BRAKE CALIPER
Perform the operation of rear brake caliper: Refer to
>> GO TO 6.
Procedure
SYSTEM MODE CHANGE
Removing/installing electric parking brake control module
—
Replacing electric parking brake control module
×
Removing/installing rear brake pad (When not pressing piston of rear
brake caliper assembly)
—
Replacing rear brake caliper assembly
—
Removing/installing parking brake switch
—
Replacing parking brake switch
—
Removing/installing clutch stroke sensor
*
—
Replacing clutch stroke sensor
*
—
Removing/installing clutch pedal
*
—
Replacing clutch pedal
*
—
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст